Sea Gull Lighting 61520-845 Installation Guide
Contents
1. _ to damage the fixture wire INSTALLATION HC 1152 IMPORTANT DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX FOR CHAIN HUNG ONLY STEP 1 Using 2 pair of pliers open one link of chain Y and connect it to the fixture loop X at the top of the fixture Slide collar ring O and canopy G to top of fixture STEP 2 Lace fixture wire up through entire chain Y and pass through canopy loop S We recommend lacing wire up through every other link of chain Y STEP 3 Using 2 pair of pliers open one link of chain on the other end of chain Y and connect it to the canopy loop S BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY A Take note of the color of the wire s on your fixture Identify which group your fixture wire s falls into and connect the wires according to the directions below GROUP A CONNECT TO BLACK HOUSE WIRE GROUP B CONNECT TO WHITE HOUSE WIRE BLACK WHITE a 4 s m PARALLEL WIRE ROUND amp SMOOTH PARALLEL WIRE SQUARE amp RIDGED EN O cs NOTE When parallel wire is used the tracer wire is square shaped or ridged and the less tracer wire is round in shape or smooth Seen best when viewed from wire end To separate wires grasp the ends of each wire and pull apart B Take your fixture wire s from group A and place evenly against the black wire from the outlet box DO NOT twist wires together before using wire connectors C Fit a wire connector not supplied over the w2. INSTALLATION AND SAFETY INSTRUCTIONS ROUNDING e Be sure the electricity to the system you are working on is turned AN D off either the fuse removed or the circuit breaker set at off e Use of other manufacturers components will void warranty listing MOU NTI NG and create a potential safety hazard e If you are unclear as to how to proceed contact a qualified electrician BAR e You don t need special tools to install this fixture e Be sure to follow the steps in the order given U P e Read instructions carefully e Save these instructions BEFORE YOU BEGIN GROUNDING Carefully remove the fixture from the carton and check that all parts SCREW D NIPPLE C are included as shown in Figures 1 amp 2 Be careful not to misplace any of the screws or parts which are needed to install this fixture FIGURE 2 NOT SUPPLIED FOR STEM MOUNT NOTE THIS FIXTURE CAN BE HUNG USING OUTLET BOX NUT B gt ad NIPPLE C CANOPY LOOP S DESIRED WIRE CONNECTORS MOUNTING BAR A GROUNDING NUT B te SCREW D QUTLET BOX NIPPLE C SCREWS CANOPY G gt SCREW COLLAR M SCREW COLLAR ASSEMBLY FOR CHAIN HUNG REFER TO FIGURE 2 COUPLING J RING 0 SS ORC UNG O FIGU i Secure mounting bar A to outlet box using outlet box ROD ASSEMBLY E STEP 1 screws not provided Thread nut B to nipple C so five threads are exposed Thread nipple C to mounting bar A and
3. ires and thread the connector clockwise until you feel a firm resistance D Gently try to remove wires from connector If you can remove wires carefully re do steps B and C as above and check again for a firm connection E Connect the fixture wire from group B to the white wire from the outlet box in the same manner STEP 2 GROUNDING INSTRUCTIONS The green grounding screw D is to be inserted into the hole with two raised dimples provided on the mounting bar Wrap the ground wire from the fixture if supplied and the ground wire from the outlet box bare metal or green insulated wire around the green grounding screw D on the mounting bar If uninsulated wire is on the mounting bar connect the ground wire from the fixture if supplied and the outlet box to it using a small wire connector not supplied NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors STEP 1 After wires are connected tuck them carefully inside outlet box and then raise the canopy G against ceiling and secure by threading screw collar ring O to screw collar M STEP 2 Raise diffuser R to socket assembly U Secure by threading retaining ring T onto socket STEP 3 Install lamp CLEANING To clean wipe fixture body with a soft cloth Clean glass with a mild soap Do not use abrasive materials such as scouring pads or powders steel wool or abra
4. secure by threading nut B to mounting bar A STEP 2 Install fixture loop X onto socket assembly U STEP 3 Feed the fixture wire from the socket assembly U through the fixture loop X canopy loop S mounted on canopy G and screw collar M lt CHAIN Y lt FIXTURE LOOP X SOCKET ASSEMBLY U FIGURE 3 SOCKET ASSEMBLY U DIFFUSER R FIGURE 1 NOT SUPPLIED E RETAINING RING T FOR STEM MOUNT REFER TO FIGURE 1 STEP 1 Secure mounting bar A to outlet box using outlet z box screws not provided Thread nut B onto nipple C so five threads are exposed Thread nipple C to mounting bar A and secure by threading nut B to mounting bar A Thread Sq gull lighting Installation And Safety screw collar M to nipple C STEP 2 Secure rods together l n str u ct l O n Feed the fixture wire from the socket assembly U H C 1 1 5 2 STEP 3 through the rod assembly E and thread rod ofeats assembly E into the socket assembly U Slide screw collar ring Line art shown may not exactly match the fixture enclosed O to socket assembly U Continue to feed wire through coupling However the installation instructions do apply to this fixture J mounted on canopy G and screw collar M Fill In Item Number On Carton And STEP 4 Secure rod assembly E to coupling J Be sure not File This Sheet For Fixture Reference ITEM
5. sive paper ORDERING PARTS Keep this sheet for future reference and in case you need to order replacement parts Parts for this fixture can be ordered from place of purchase Be sure to use exact wording from illustration when ordering parts
Download Pdf Manuals
Related Search