Worldwide Lighting W23318F19 Instructions / Assembly
Contents
1. W 23318F19 D19 H32 L3 2 We are dedicated to providing the finest quality crystal chandelier for our customers Our master craftsmen and designer pride themselves on their attention to detail Prompt efficient service is our priority Enclosed are detailed instructions on how to properly install your chandelier Please read all instructions carefully and thoroughly If you have any questions please fell free to call our toll free CHANDELIER HOTLINE AT 1 855 411 8999 GD Crystal Dressing Instructions CANOPY PARTS LIST When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals Existing Electrical Box Crossbar Screws x 2 not srpplied Ye Crossbar Screws O O O 1 4mmX 1 1 4mmX2 8strings O 2strings 2strings lstring lstring J Wire Connector 14mmX9 14mmX9 14mmX 1 14mmX 1 m 14mmX4 14mmxX5 oo Pl AmmX Shrinkable tube W 14mmX1 12strings a7 YY og 3strings 2strings 2strings RAIDE Cable tie Ground Wire Cy CANOPY INSTALLATION DIAGRAM Frame Parts List 01 Crossbar 02 Lamp Body _ 4 i 03 Crossbar Bracket WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING After passing the main eiectrical wire t2. hrough the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing Cleaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or circuit breaker before doi
3. ircuit breaker before doing any installation Elegant lighting shall not be responsible for unprofessional wiring Frame Assembly Instructions Installation Please read all instructions carefully Before you proceed to install make sure that the power supply is turned off and remains off until installation is complete please note that each part has been assigned a number please proceed in a numerical order 1 Fix the crossbar 01 on junction box 2 Make sure the positive and negative charges of wire and lamp body match correctly screw the connect point with the junction cap 3 Make sure the main wire is enough long and keep the rest wire in the 4 j box 4 Screw the lamp body 02 on Crossbar 01 With Crossbar Bracket 5 As the crystal pressing instruction hang the crystal parts The end
4. ng any installation Elegant lighting shall not be responsible for unprofessional wiring Crystal Dressing Diagram When dressing the chandelier with the crystals please remember to wear either rubber or cotton gloves So as to prevent any damage or smudging on the crystals CWN We W er Aa ib me o AANS A CAS AL Q S Frame Assembly Diagragram CANOPY INSTALLATION INSTRUCTIONS Please read all instructions carefuly Before you proceed to install make sure that the power supply is turned off and off until installation is complete Please note that each part has been asigned a letter Please proceed in an alphabetical order A Existing Electrical Box Crossbar Crossbar Screws Junction Caps Metal Base Neutral Conductor Ground Wire Hot Wire Crossbar Bracket fe mb PEC gee e ge NET A y u SX me a PA X 2 M Ne dde WN 2 Al AUX ou NES wW D A Aa o Ne AK Ve so SMS 7 ett le SS A NN ey Pay i 1 Fasten Crossbarbar B into the Existing Electrical Box A with screws C 2 Connect and hot wire H neutral wire F and ground wire G correctly and tighten them with cap D 3 Fix the Metal Base and tighten it with 1 WARNING CONTENTS ARE FRAGILE HANDLE WITH CARE The metal frame and crystal components of this chandelier are very delicate Please excersise extreme Caution during unpacking and installation WARNING Afte
5. r passing the main eiectrical wire through the 10mm pipe and connecting the pipe to the main body top connector place all remaining pieces as shown in nurmerical order and in the orientation depicted Refer to the parts list to avoid confusion between parts The part Numbers coincide CAUTION 1 Rated 110v 130v 60Hz bulb E12 40W maximum 2 Care Should be taken to avoid damage to the surface of lighting and wire wearing gloves is recommended when installing 3 Connect black or red wire of the lighting to live wire and white or blue wire to neutral wire and double colored or bare copper wire to ground wire 4 Never install lighting on damp ceiling the room should be dry and well ventilated 5 Keep lighting away from acid alkali and other corrosive chemical or gas clean the lighting with Clean soft cloth only 6 Installation must be carried out by qualified electrician only 7 Disconnect the power before installing Cleaning and replacing lighting 8 Never cover the lighting when power is connected 9 Firmness must be secured when installing ceiling tube chain pipe and other connecting parts 10 Care should be taken to avoid damage when installing glass parts 11 All electrical components must be installed by a licensed electrician and in accordance with the National Electrical Code and the appropriate local electrical codes Make sure that the elecrtrical supply to the chandellier is turned off at the main fuse or c
Download Pdf Manuals
Related Search