Bosmere A026 Installation Guide
Contents
1. ZN gt St Tropez Cano English SS204E ROWLINSON P py 8 NS GARDEN PRODUCTS Assembly Instructions Before assembl We recommend that time is taken to read the instructions before starting assembly then follow the easy step by step guide The instruction sheet is only a guide to the assembly Certain items may not be shown to scale Check all components prior to assembly This product should be assembled by no less than two people e Never attempt to erect the assembly in high winds Drill components where indicated Recommended tools for assembl Drill 10mm diameter drill bit Hammer 10mm spanner Spirit level Step ladder Alan key provided Caution When connecting components that use the spring button Please ensure the button is properly located in the hole No Components Qty Left track section with wall bracket l 2 Right track section with wall bracket l 3 Runner 10 4 Track section 2 5 Centre track section l 6 Centre track and upper leg l 7 Left upper leg l 8 Right upper leg l 9 Front connecting bar 2 10 Rear connecting bar 2 II Lower leg 3 12 Curl finial 3 13 Ball finial 3 14 Foot plate 3 15 Brace 1675mm 4 16 Brace 1605mm 4 17 Canopy tubes 1590mm 2 18 Canopy tubes with push button 10 19 Polyester cano2. d leave to dry naturally Do not use bleach acid or other solvents e Do not machine wash e Do not tumble dry Safety In order to gain the most from your new canopy attention should be paid to the following safety precautions I Periodically check bolts and fittings for tightness as they may work loose over time taking care not to over tighten fittings as this may damage the metalwork For this reason we do not recommend the use of power tools to assemble the canopy frame 2 Please note that the metal frame is not to be used as a climbing frame FIRE PRECAUTIONS e PLEASE NOTE THAT THE CANOPY IS NOT FIRE RETARDANT AND CAN BURN e DO NOT USE NAKED FLAMES IN THE VICINITY OF THE CANOPY e BARBECUES AND OR PATIO HEATERS SHOULD NOT BE USED EITHER UNDERNEATH OR IN THE VICINITY OF THE CANOPY If in doubt of any aspect regarding the assembly use or safety of your canopy please contact us Help Line Normal Office Hou rs 01829 261 121 We constantly improve the quality of our products occasionally the components may differ from the Pale et GARDEN PRODUCTS LIMITED components shown and are only correct at time of Wardle REN ich printing We reserve the right to change the kahe FNantwic specification of our products without prior notice CW5 6BN 2011 Rowlinson Garden Products Ltd
3. end Secure to the top of the frame using 4 x 10mm bolts as shown below Ensure the two centre eyelets are at the back and are hooked over the two bolts that are connecting the rear connecting bars Important information e Please ensure that the canopy is erected on a stable level and sturdy surface e Ideally the canopy should be fixed to a level concrete patio base using appropriate fixings If the canopy is to stand on grass it is important that the canopy is level in order to ensure a smooth retracting mechanism and the canopy should be secured into place using fixing pegs supplied e When erecting the canopy frame judgement should be used to determine the most appropriate fixing component to attach the metal plates to the exterior wall bearing in mind the strength and condition of the wall If deemed inappropriate substitute the included wall fixing e Please note that the St Tropez Canopy is not designed to be used as a rain shelter despite the polyester canopy being shower proof e We recommend that the polyester canopy be fully retracted when not in use e The polyester canopy should be fully removed in anticipation of strong winds and during the winter period e The polyester canopy must be completely dry before storage e Eyelets in the canvas are drain holes to prevent water collecting and stretching the canvas Maintenance e To clean the polyester canopy sponge clean using a mild soap and water solution an
4. er will result in the canopy being unsafe 4 Lower legs and finials Plastic spacer Height adjust holes Connect the lower leg to the upper leg ensure the push button mechanism on the lower leg is properly located in the hole of the upper leg Position the curl finial on top of the leg Put the plastic spacer over the screw thread of the ball On the bottom of each lower leg insert a foot finial Screw the ball finial through the hole in plate Align the holes of the lower leg and foot the curl finial into the hole in the top of the leg plate and secure together using x 60mm bolt and nut per foot Please note i The two holes in the post of the foot plate are to adjust the height of the canopy Ensure the same height hole is use on all three legs Corse 5 Connecting frame to the wall When erecting the canopy frame judgement should be used to determine the most appropriate fixing component to attach the metal plates to the exterior wall bearing in mind the strength and condition of the wall If deemed inappropriate substitute the included wall fixing Canopy wall plate Wall Nut Canopy wall plate Washer Canopy wall plate Spring washer Fixing bolt Canopy wall plate Put the canopy frame into position ensure the feet are flat on the floor and the tracks are level using a sprit
5. level Mark the wall with the position of the 4 holes of each wall plate For included fixings Remove the frame work and drill 10mm diameter holes at positions marked to a depth of 50mm Gently tap the fixing bolts into the hole Reposition the canopy frame on to the studs and secure using the washer spring washer and the nut 6 Frame bracing Insert a 1675mm brace through each of the holes in the centre track and connect it to a 1605mm brace as shown Fit the outer ends of the braces between the outer tracks and secure using x 35mm bolt at each end Push the bolts through the track frame and screw into the ends of the braces With all braces in position screw down through the holes in the top of the centre track into each brace using x 16mm screws for each brace 7 Attaching the wall end of the polyester canopy Insert the two 1590mm canopy tubes into the two loops at one end of the canopy Position the two canopy tubes with canopy against the rear connecting bars and secure using 4 x 35mm bolts Push each of the ten round canopy tubes through the holders of the runners through the loops in the canopy and connect to the centre runners ensuring that the push button mechanism properly locates to lock components together 9 Attaching polyester canopy cover Position the polyester canopy cover on top of the metal frame at the wall
6. py l 20 Polyester canopy cover l No Fixing Kit Qty 21 60mm bolts with nuts 3 22 35mm bolt 12 23 10mm bolt 32 24 16mm screws 25 Plastic spacer 3 26 Wall fixings 12 27 Foot pegs 6 28 Plastic caps 47 Outer Tracks Insert five runners into each of the two outer tracks sections with wall bracket Connect the track sections to the track sections with wall bracket by inserting the coupling into the upper tube of the track with wall brackets Secure in place using 6 x 10mm bolts for each join Attache the upper legs in the same way using 2 x Omm bolts ensure correct orientation shown in diagram 2 Centre track Assemble the centre track and upper leg section in the same way as the outer tracks Make sure the pulley rope is not trapped in any of the joins and is able to operate freely 3 Front and rear connecting bars Join the rear of the three track assemblies using the rear connecting bars push the bars in to the sockets of the track sections as shown Secure in place using x 10mm bolt at each end Join the front of the three track assemblies using the front connecting bars push the bars in to the sockets of the legs as shown secure by ensuring the push button mechanism in the legs properly locates into the hole of the connecting bar Please note Failure to ensure the button mechanism is locking the components togeth
Download Pdf Manuals
Related Search