PRO-SERIES DS1830 Instructions / Assembly
Contents
1. RS6001 Item Qty Content PR11 16 leg bearing PR 12 16 1 4 flat washer PR 13 8 1 4 20 locknut PR 27 8 1 4 20 x 3 cap screw RS6002 Item Qty Content PR 35 8 strap mounting screw PR 17 8 strap mounting washer PR4 2 adjustable double hook amp loop leg strap PR7 2 adjustable double hook amp loop arch strap PR8 2 adjustable single hook amp loop toe strap RS6003 Item Qty Content PR 37 16 sole mounting screw PR 46 4 replaceable sole for nylon floor plate RS6004 Item Qty Content H45 2 entire spring assembly RS6005 Item Qty Content PR1 2 leg band with pad PR2 4 leg band spacer PR3 4 1 4 20 x 2 flat head machine screw PR 12A 4 1 4 flat washer PR 13 4 1 4 20 locknut RS6006 Item Qty Content PR 29 2 round lock front tube clamp PR 30 2 round lock rear tube clamp PR 31 2 metal clamp bracket PR 14 2 1 4 20 insert locknut PR 12A 4 1 4 flat washer PR 17 4 strap mounting washer PR 28 4 1 4 20 x 1 3 4 cap screw with square nut PR 32 2 1 4 20 x 1 3 4 cap screw with locknut RS6007 Item Qty Content PR 48 4 downward large nylon sleeve PR 49 4 upward small nylon sleeve RS6008 Item Qty Content PR 42 4 wing bolt with lockwasher RS6009 Item Qty Content PR 10 2 adjustable heel Bracket PR6 4 no 10 24 x 1 2 machine screw with nut PR 6A 4 1 4 20 15 8 cap screw2. adjusting stilts up and down Replace wing bolts and tighten OPERATION GUIDELINES Walking precautions IMPORTANT Always take short deliberate distinct steps and walk with your stilts well apart Large or over extended steps can cause the action springs to bottom out and place excess stresses on the stilt components Excess stresses could drastically reduce the life of the stilts or result in component breakage Inspect before working Develop a habit of inspecting your stilts before each days use Make certain the entire stilts are free of any sign of damage or excessive wear and that all nuts and bolts are tight Special attention should be given to the entire strut tube assemblies and wing bolts in this respect Keep all labels legible Strap tightening sequence Important When mounting your stilts always attach leg straps first before feet When dismounting always unbuckle leg straps last after unbuckling foot straps Select a clear and level area away from doors floor vents stairwells windows etc With the help of a colleague strap on your stilts as noted above Stand with your legs comfortably apart collect your balance and relax If needed re adjust the strut tubes and clamps until your stilts and legs are straight and comfortable Forward rearward balance When standing erect your stilts should be in a neutral and vertical position If they have a tendency to lean forward or backward make the following adjus
3. Drywall Stills DS1830 Max Weight Capacity 225 Lb READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT This manual provides important information on proper operation amp maintenance Every effort has been made to ensure the accuracy of this manual These instructions are not meant to cover every possible condition and situation that may occur We reserve the right to change this product at any time without prior notice IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE DO NOT USE THIS PRODUCT DO NOT RETURN THIS PRODUCT TO THE RETAILER CONTACT CUSTOMER SERVICE If you experience a problem have questions or need parts for this product visit our website http www buffalotools com or call Customer Service at 1 888 287 6961 Monday Friday 8 AM 4 PM Central Time A copy of the sales receipt is required 201107 ATTENTION READ THIS PLEASE ENSURE ASSEMBLY INSPECTION AND MAINTENANCE IS CARRIED OUT PROPERLY THIS IS CRUCIAL TO YOUR PRODUCT SATISFACTION AND PERSONAL SAFETY IT IS YOUR RESPONSIBILITY TO READ THESE INSTRUCTIONS INCLUDING THE DO S AND DON TS GUIDELINES DETAILED WITHIN IT IS ALSO YOUR RESPONSIBILITY TO USE STILTS THAT ARE WELL MAINTAINED TO INSIST ON A CLEAN CLEAR WORK AREA AND TO ALWAYS EXERCISE CAUTION WHILE USING SUPA STILTS CHECK ALL BOLTS ARE TIGHT BEFORE USE AND PAY SPECIAL ATTENTION TO THE ENTIRE STRUT TUBE ASSEMBLIES AND WING BOLTS IF YOU HAVE CONCERNS ABOUT CONSTRUCTING
4. OR USING THE STILTS PLEASE CONTACT US WILL NOT BE HELD RESPONSIBLE FOR ANY ACCIDENT RESULTING FROM IRRESPONSIBLE USE IMPROPER USE OR FAILURE TO INSPECT AND MAINTAIN ACCORDINGLY DO NOT EXCEED LOAD LIMIT 225 LBS IMPORTANT GUIDELINES TO FOLLOW BEFORE ASSEMBLY OR USE DO Inspect stilts thoroughly before use making sure that construction is free from damage and hazards that there is no excessive wear at the connection points and that all bolts are tight Special attention should be given to the entire strut tube assemblies and wing bolts in this respect Walk only on suitable hard surface which is level Be cautious when working around low profile furniture fixtures pipes etc Fasten the upper leg strap first when putting on stilts Disconnect upper leg straps last when removing stilts Replace any damaged or excessively worn stilt components before use Remove stilts to adjust them unless assisted by another person Remove stilts when moving up and down stairs Cover any floor openings Get help when retrieving objects from the floor If no one is around remove them completely Keep all straps tightly fastened and secured Take short steps making sure that the stilts are raised well clear of the floor with each step Walk forward only making a U turn to change direction Adjust Stilts whenever necessary to ensure it is safe Always watch where you are walking DO NOT Wear stilts without hav
5. PR22 1 4 77 8 stud threaded at both ends 2 PR23 15 Inter Lock 1 0 D lower strut tube PW1523 2 PR23 18 Inter Lock 1 0 D lower strut tube PW1830 2 PR23 24 Inter Lock 1 0 D lower strut tube PW2440 2 PR24 1 4 20 1 5 8 cap screw 2 PR25 Foot plat bush 8 PR26 Floor nylon plate 2 H27 1 4 20 31 8 cap screw 8 PR28 1 4 20 1 5 8 cap screw w square nut 4 PR29 Side pole cap clamp 2 PR30 Side pole support clamp 2 PR31 3mm clamp bracket 2 PR32 20x1 3 4 cap screw 2 PR33 Upper side pole cap plug 2 PR35 Strap mounting screw 8 PR37 Sole mounting screw 16 PR42 Wing bolt 4 PR44 Lower coil spring 2 PR45 Entire spring construction 4 PR46 Replacement sole 4 PR47 15 Forward adjustable leg extrusion PW 1523 4 PR47 18 Forward adjustable leg extrusion PW 1830 4 PR47 24 Forward adjustable leg extrusion PW 2440 4 PR47A Center apring assembly bracket 4 PR48 Downward nylon sleeve 4 PR49 Top stopping small nylon sleeve 4 PR50A Upper foot pad attachment bracket 4 PR50B Inter Lok bracket 2 PR50C Upper amp lower spring assembly bracket 4 PR51 15 Inner extension tube PW 1523 4 PR51 18 Inner extension tube PW 1830 4 PR51 24 Inner extension tube PW 2440 4 PR51A Lower foot pad attachment bracket 4 Repair Kit
6. djust the action springs Make the following adjustments after removing your stilts To correct for leaning forward while walking tighten the upper spring adjuster To correct for leaning backward while walking tighten the lower spring adjuster Never tighten adjusters more than 1 5 of the way down or approximately 15 turns as it will limit the stilt action and impose excess stresses on the components PARTS DIAGRAM Parts List Part No Description Qty PR1 Leg band with pads 2 PR2 Leg band spacer 4 PR3 1 4 20 2 flat bead machine screw with locknut 4 PR4 Adjustable double hook amp loop fastening leg strap 2 PR5 15 1 8 upper strut tube PW1523 2 PR5 18 1 8 upper strut tube PW1830 2 PR5 24 1 8 upper strut tube PW2440 2 PR6 No 10 24 1 2 machine screw with nut 4 PR6A Locknut 4 PR7 Loop fastening arch strap 2 PR8 Loop fastening toe strap 2 PR9 Nylon foot plate 2 PR10 Adjustable heal bracket 2 PR11 Leg bearing 16 PR12 1 4 flat washer 21 PR12A 1 4 flat washer SAE 16 PR12B 1 4 square nut 12 PR13 1 4 20 locknut H5 12 PR14 1 4 20 hex nut H8 4 PR15 Spring adjuster 4 PR16 Upper coil spring black 2 PR17 23 4 3 4 strap mounting metal plate 8 PR18 Nylon spring bearing 8 PR19 No 3 8 self threading screw 8 PR19A 8 flat washer 12 PR19B 8 lock washer 8 PR2O Spring Divider 2 PR21 Support washer for leg band 4
7. ghten the tube clamps to prevent the upper strut tube from rotating when used Over tightening the tubes could permanently deform them and require their replacement Position the tube clamps in the clamp bracket slots according to your calf size so the stilts will stand straight when mounted and tighten well Attach the heel brackets to the footplates using the No 10 x 1 2 Phillips machine screws and nuts Adjust the heel bracket so your outside ankle bone is directly over the rear pivot bolt and tighten well Strap Kit 1 Position the toe short and arch long straps on the footplates with the fasteners on the same side as the strut tube 2 Feed the ends of both straps over and through the Safety Anchor Slot System and secure the straps with the strap plate amp screws provided 3 Set spring adjusters to minimum compression Set adjustable stilt legs to the lowest setting and tighten wing bolts 4 Re check all the components you have assembled Reposition the tube clamps and leg bands until you feel totally comfortable You should stand straight on your stilts so the stilts don t pull in or out Height Adjustment When adjusting the heights of the stilts remove wing bolts Once removed evenly raise the stilt legs to the desired height Once height is achieved re align the wing bolt holes in legs and extension tubes replace the bolts and tighten well Be sure not to over t
8. ighten as this can have adverse effect Wing bolts for height adjustment MAINTAINANCE Lubrication In order to keep your stilts operating freely it is necessary to keep the components reasonably clean and free of dents or burrs Pay special attention to the components which help operate the movement Lubricate these moving components lightly with a silicone spray or white graphite powder Do not use lubricating products which remain wet and attract grit or any type of chemical cleaner Make certain soles are kept free of lubricants which could cause loss of traction WARNING Do not make modifications on parts Always use genuine replacement parts Contact dealer for more information Replacement Nylon Sleeves Remove wing bolts and remove the upper foot plate together with the extension tubes and floor plate Pry the small sleeves from the extension tube upper ends and remove The large sleeves can now be removed To reassemble check extension tube holes for burrs file smooth Slide new large sleeves down over the extension tubes until the large sleeve tabs are aligned over the detents at the bottom of the extension tubes Insert new small sleeves over the top of the extension tubes until it snaps past the upper locking tabs of the extension tubes Carefully insert the extension tube units all the way into the stilt legs until the large sleeve tabs snap and lock into the stilt leg slots Check stilt operation by
9. ing the proper instruction Wear stilts that are uncomfortable or not adjusted properly Wear stilts without having first inspected them for obvious hazards Wear stilts that have clearly been misused damaged or modified Walk on slippery surfaces Work around uncovered floor openings stairwells etc Work in or around loose items e g wires cords material e t c Carry heavy loads while walking on stilts The Stilts have a load limit Run or walk fast on stilts Pick up objects which are lower than foot level Wear stilts that are taller than necessary Lean over desks files boxes or other objects while on stilts Be irresponsible on stilts Take steps so large that the action springs fall out This can cause serious Injury Modify this product in anyway Wear stilts while under the influence of drugs or alcohol Walk on secondary scaffolding benches planks etc ASSEMBLY INSTRUCTIONS Strut Tubes 1 Loosen tube clamps Insert lower strut tubes up through the bottom of the tube clamps Leave tube clamps whilst you prepare the other parts Attach lower strut tubes to the safety lock bracket with the attached 1 4 x 1 1 2 cap screw amp nylon lock nut Tighten when assembly is complete Slide the upper strut tubes down over the lower strut tubes and through the tube clamps Position so the leg bands are just above the large portion of the leg calves Note Do not bend the leg bands Evenly ti
10. tments with the help of a colleague or after removing your stilts If stilts lean forward loosen the tube clamps and rotate the leg bands and strut tubes toward the rear and tighten clamps This adjustment is to insure proper forward and backward balance If this adjustment requires that the leg bands be rotated to where it is uncomfortable the mounted shoes should be relocated or the heel brackets be adjusted in the same direction as the needed rotation Note Do not bend or size leg bands LEARNING TO WALK IMPORTANT Read the do s and don ts for the use of your stilts before you attempt to learn to walk on them Remember in order to develop safe work habits it is very important that you observe the do s and don ts as you learn to walk on and work with them Select a clear and level area preferably near a wall but away from doors floor vents stairwells windows etc With the help of a colleague mount your stilts and take slow deliberate short steps while keeping your stilts well apart Make certain that each step completely clears the floor as you must never drag or shuffle your feet While assisted walk slowly back and forth numerous times making a U turn to reverse your direction Repeat walking back and forth until you develop a feel for the stilts Practice walking until you feel secure and are able to walk unassisted ADJUSTMENT FOR WALK If you have a tendency to lean forward or backward while walking you should a
Download Pdf Manuals
Related Search