Wagner 0529011 Installation Guide
Contents
1. Air vent on suction tube blocked Material flow setting too low Suction tube loose No pressure build up in container Air valve tube not functioning Nozzle seal missing Air filter clogged Spray material too thick Nozzle loose Nozzle worn Nozzle seal missing or worn Material build up on air cap and nozzle Problem B Material leaking Problem C Spray pattern too thick runs and sags Material flow setting too high Air power setting too low Applying too much material Nozzle clogged Air filter clogged Too little pressure build up in container Spray material too thick Problem D Spray jet pulsates Air filter clogged Air valve tube disconnected Problem E Too much overspray Gun too far from spray object Air power setting too high Problem F Pattern is very light and splotchy Moving the spray gun too fast Material flow setting too low Air power setting too high Note Generally material should only need to be thinned when using the Detail Finish nozzle Only thin the material as a last resort to improve spray performance Optimal spray performance should be acheived simply by adjusting the various controls on the unit This unit contains no servicable electrical parts Do not attempt to service yourself Store indoors with the cord wrapped around the turbine handle having problems In the United States to speak to2. steps to replace it IMPORTANT Never operate your unit without the air filters Dirt could be sucked in and interfere with the function of the unit 1 Unplug the spray gun Push the snap levers a on the two turbine covers and remove them Remove the dirty filters and replace with new ones The smooth side of the air filter must be placed toward the turbine Secure the covers back onto the turbine Cleaning the Air Valve Tube Note If paint has entered the air tube proceed as follows 1 Pull the air tube a at the top from the nozzle Screw off the valve cover b Remove the valve seal c Clean all the parts carefully IMPORTANT The air tube and valve seal c are only solvent resistant to a limited extent Do not immerse in solvent only wipe 2 Place the valve seal c in the valve cover b with the pin facing into the tube Note Installing the valve seal into the valve cover will be much easier if the valve cover is inverted 3 Turn the nozzle upside down and screw on the valve cover with valve seal inside from underneath Note Turning the nozzle upside down will prevent the valve seal from falling out of the valve cover during reinstallation 4 Place the air tube on the valve cover and on the nipple at the nozzle a rt Pos Wagner Spray Tech All Rights Reserved 15 Troubleshootino Problem A Little or no material flow Nozzle clogged Suction tube clogged
3. To Reassemble 1 Install the nozzle seal 1 with the groove a slot facing toward the nozzle away from the front end assembly 2 Insert the nozzle 2 Make sure to align the groove b and notch c and align the nozzle opening with the needle 3 Put the air screen d in the air cap e Put both 3 on the nozzle 2 and secure with the connecting nut 4 Note This step is easier if the iSpray nozzle is facing up 4 Snap the adjustment ring 5 into the connecting nut 4 enabling the adjustment lever f on the peg g to be positioned in the air cap Note Make sure that the two recesses on the adjustment ring are engaged in the air cap tabs 5 Reattach the nozzle to the turbine Note Make sure the air valve tube is free of paint If not clean the air valve tube by following the instructions on the next page If clean make sure it is attached securely at both ends see inset Nozzle seal DO NOT LOSE It is important that the nozzle seal inside the nozzle be re installed properly Make sure the cup side of the seal the side with the groove is facing out towards the front of the nozzle Improper installation will cause leakage and damage to the turbine 14 Wagner Spray Tech All Rights Reserved Cleaning the Filters IMPORTANT Before every use you should inspect the air filters in the turbine to see if it is excessively dirty If it is dirty follow these
4. a customer service representative call our Technical Service at 1 800 328 8251 See www wagnerspraytech com in the 9 Have you tried the recommendations above and are still Contact Us section for Technical Service hours Material in container running out Clean Clean Clean see page 13 Increase material flow setting Remove and replace as tightly as possible Tighten container Make sure both ends of the tube are connected and the valve seal is in place Replace Change Thin Tighten Replace Replace extras provided Clean Decrease material flow setting Increase air power setting Adjust material flow or increase movement of spray gun Clean Change Tighten container Thin Refill Change Reconnect both ends of the air tube Reduce distance 6 8 is ideal Decrease air power setting Adjust material flow or de crease movement of spray gun Increase material flow setting Decrease air power setting Wagner Spray Tech All Rights Reserved
Download Pdf Manuals
Related Search