BEHR Premium 50201 Installation Guide
Contents
1. be complete dry before application Intermix multiple containers to ensure color uniformity DO NOT THIN PRODUCT Stir product occasionally throughout application Test product for penetration and color on a small hidden area before proceeding Use a nylon polyester brush for areas requiring more accuracy Use of rollers should be limited to rough surfaces only Use 3 8 nap or longer when appropriate A high quality pump WARRANTY rent Weatherproofing Soap amp Water Clean Up sprayer with a variable tip or an airless sprayer with a 015 019 tip may be used Work in small sections lightly saturating the surface and immediately back brush or use pad applicator to eliminate puddling r excess and evenly distribute the finish Maintain a wet edge when applying Apply product end to end or to board lengths to prevent lap marks Over application of finish will lead to surface failure including peeling and cracking Avoid applying finish too heavily Two thin coats required For optimum performance coat all six sides of wood DRY TIME 1 2 hours before recoat Allow 72 hours for full cure DISPOSAL For disposal of empty containers and unused product contact your household refuse collection service WARNING If you scrape sand or remove old paint you may release lead dust LEAD IS TOXIC EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS SUCH AS BRAIN DAMAGE ESPECIALLY IN CHILDREN2. BEHR PREMIUM Trans All In One Wood Finish For Decks Fences amp Siding Penetrating Advanced 100 Acrylic e Enhanced UV Protection e Mildew Resistant Finish Easy Water Clean Up WEATHER PROOFING 2 Thin Coats Required CAUTION Finished surfaces may become slippery when wet WHERE TO USE For Wood Substrates Only Recommended for properly prepared new to slightly weathered unsealed exterior wood surfaces 0 5 years exposure such as Decks Railings Shakes Shingles Siding Roofs Fences and Wood Patio Furniture PREPARATION t The following steps and products are required Use a product such as BEHR PREMIUM NO 64 Wood Stain amp Finish Stripper to remove loose wood fibers latex oil based and 100 acrylic coatings on new or weathered wood BEHR PREMIUM NO 63 All In One Wood MUST be used following NO 64 to clean brighten amp neutralize wood When NO 64 is not needed use a product such as NO 63 to clean and brighten the wood surface and to remove light to medium exterior stains caused by mold mildew algae amp fungus On new wood use a product such as NO 63 to remove mill glaze and open the pores of the wood Rinse thoroughly and allow to dry before coating Lightly sand to remove remaining wood fibers fuzz APPLICATION For best results a pad applicator is recommended over large deck areas Must applybetween 40 90 F 4 5 32 C Do not use if rain is expected within 24 hours The wood surface must
3. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE Wear a NIOSH approved respirator to control lead exposure Clean up carefully with a HEPA vacuum and a wet mop Before you start find out how to protect yout and your family by contacting the National Lead Information Hotline at 1 800 424 LEAD or log on to www epa gov ead WARNING Sanding or scraping pressure treated lumber may be hazardous wear appropriate protection Visit www Betr com for complete warranty information 2013 Behr Process Corporation EHRee A Masco Company Santa Ana CA S2T04 USA behrcom VOC CON lt 275 g l REV 3113 ns chemicals known to the state of California to c productive harm WARNING IRRITANT HARMFUL IF SWALLOWED CONTAINS ETHYLENE GLYCOL MAY CAUSE EYE NOSE AND THROAT IRRITATION AVOID CONTACT WITH SKIN ANDI EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST WEAR EYE PROTECTION WARNING Ti e cancer nd birth de AND PROTECTIVE CLOTHING USE ONLY WITH ADEQUATE VENTILATION To avoid breathing t ndows and doors or use other means to ensure fresh air ice eye watering headaches or dizziness pproved for organic vapor with P rofessional advice before s Avoid contact with eyes h use FIRST AID If you difficulty is
Download Pdf Manuals
Related Search