FAMOWOOD 5050110 Use and Care Manual
Contents
1. NOTE If temperature is above 70 F working time decreases Spread the mixture over the area with a plastic spreader plastic squeegee notched trowel or brush If coating a large surface such as tables bar tops etc a notched squeegee or trowel works well see Large Area Applications section Pour mixture on surface and spread evenly using a combing action in one direction over entire surface Do not persist in re spreading the mixture as it sets up otherwise it will not self level during the curing action Do not pour more than 1 8 thick in an application Mix only as much as you can pour and spread at one time FAMOWOOD GLAZE COAT High Build Coating Rev 05 Effective 2014July Approved 35TMorgan Page 2 USA wt I Technical FAMOWOOD GLAZE COAT Data Sheet HIGH BUILD EPOXY COATING Step 4 Surface Bubbles At initial pour air bubbles created during the mixing process will usually rise to the surface by themselves and disappear However because Glaze Coat is very thick it is usually necessary to help this process along immediately after pouring and spreading Surface bubbles MUST be removed when surface is still wet not once surface begins the curing process or else bubbles will turn into dimples once fully cured Blow gently on the surface to force bubbles up and away For larger areas use a small handheld propane torch Keep flame 6 to 8 inches above surface Move t2. Technical Data Sheet ECLECTIC IN THE HOME amp ON THE JOB PRODUCTS Eclectic Products Inc Manufacturing Facility 101 Dixie Mae Drive Pineville Louisiana eclecticproducts com 800 349 4667 ISO 9001 2008 Compliant Quality Management Systems Administration Office Eugene Oregon eclecticproducts com 800 693 4667 USA CANADA l FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING PRODUCT DESCRIPTION FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING is an ultra clear high gloss finish epoxy versatile enough to be used on just about any surface either smooth or rough stained or painted This easy to use 1 1 ratio is ideal for household and craft projects just one pour equals 70 coats of varnish WHERE TO USE APPLICATIONS This ultra clear high gloss finishing epoxy is ideal for home improvement and craft projects coat tables clocks game boards and furniture imbed coins rocks sea shells flowers or any non waxy material preserve pictures photographs posters signs and ceramics FEATURES AND BENEFITS HIGH BUILD EPOXY just one pour equals 70 coats of varnish EASY TO USE no measuring errors easy 1 1 mixing ratio VERSATILE may be used on any non waxy material SELF LEVELING minimal spreading and maintenance required SHELF LIFE not applicable duration of shelf life has no effect on product performance Mixing ratio Pot life working time Tack
3. clean unwaxed disposable paper or plastic cups or tubs Mix MUST be a one to one ratio Resin A Hardener B by volume meaning equal parts resin and hardener If possible use a calibrated container Measure First mix Pour the carefully measured Hardener Side B into the container with measured Resin Side A and thoroughly mix for Us ep six minutes Mix with a stir stick using vigorous eg steady revolutions With proper mixing some air bubbles occur naturally and can be removed after the pour see Step 4 It is very important to scrape all sides and the bottom of Da wn the container with your stirring stick as you mix First Mix Second mix Pour the Resin and Hardener from first Resin A mix into a clean mixing container and thoroughly mix for an additional six minutes Itis EXTREMELY IMPORTANT to follow Step 1 and Step 2 as described above DO NOT allow mixture to sit or it will harden overheat and become hot to the touch Second Mix 1 Cup Resin into Hardener 6 minutes mm nd P 2 Cup Resin amp Hardener Seinus Thisstepis very into new clean container IMPORTANT to ensure a complete mix When the resin and hardener are first poured together the initial mixture appears hazy Step 3 Pour Pour Glaze Coat IMMEDIATELY onto the center of the surface to be covered Do not allow it to sit You have about 15 20 minutes working time before product begins to harden
4. IMITED WARRANTY The product is warranted against any defect in materials or workmanship under normal use for a period of 180 days after the date of purchase The product is also warranted under any implied warranties provided under applicable state law including without limitation the implied warranty of merchantability and the implied warranty of fitness for a particular purpose for a period of 180 days after the date of purchase This warranty covers only the original buyer of the product For warranty service the buyer should contact the store where the product was purchased or write Eclectic Products Inc P O Box 4450 Pineville LA 71361 or call 800 767 4667 This warranty gives you specific legal rights and you also have other rights which vary from state to state FAMOWOOD GLAZE COAT High Build Coating Rev 05 Effective 2014July Approved 35TMorgan Page 4
5. ation procedures are necessary due to the size of the application Bar tops and table tops used for dining require special preparation GLAZE COAT is not recommended for floors Use in well ventilated area only Avoid breathing vapors Wear gloves and appropriate skin protection Best when used between 70 and 85 F 21 and 29 C DO NOT change ratio and add any solvents Wood surfaces since most woods are porous seal the surface with a thin coating of GLAZE COAT applied with a squeegee to help prevent air bubbles from forming while the main pour is in process e May damage finished surfaces Avoid such contact until completely dry Not recommended for use on polystyrene polyethylene polypropylene Styrofoam or paper products and any items that come into contact with food drinking water or animals FAMOWOOD GLAZE COAT High Build Coating Rev 05 Effective 2014July Approved 35TMorgan Page 3 USA CANADA I Technical FAMOWOOD GLAZE COAT Data Sheet HIGH BUILD EPOXY COATING HEALTH and SAFETY This product contains epoxy resin nonyl phenol and allyl diamine resin Before working with this product read and become familiar with information concerning hazards proper use and handling MSDS is available on line at eclecticproducts com msds glazecoat_english_hardener_resin pdf to request a hard copy of the MSDS please send an e mail to msds eclecticproducts com or call 800 333 9826 L
6. free time Cure time Weight gallon Service temperature Storage temperature Shelf life Application temperature PHYSICAL PROPERTIES Natural color Clear Tensile strength 450 psi Tear strength 200 psi Shear strength 200 psi Compressive strength 800 psi Compressive strain 75 Elongation 15 Shore hardness 85A Solids content 100 Non volatile content 97 1 to 1 volume 15 minutes 70 F 21 C 12 hours 70 F 21 C 72 hours depending on temperature Part 1 9 63 Part B 7 93 77 F 25 C ASTM D 1475 70 to 80 F 21 27 C 10 to 120 F 12 to 49 C D not store above 95 F 35 C if materials are hot bring them to room temperature 77 F 25 C before mixing 1 year FAMOWOOD GLAZE COAT High Build Coating Rev 05 Effective 2014July Approved 35TMorgan Page 1 USA wt I Technical FAMOWOOD GLAZE COAT Data Sheet HIGH BUILD EPOXY COATING DIRECTIONS and APPLICATION NOTES Preparation Before Mixing Surface must be dry sanded and free from dirt dust grease wax or oil Do not apply over damp or waxed surfaces Cover work area with waxed paper or equal Elevate object to be coated on supports i e paper cups Be sure object is level Have dust cover ready to use after pour Wear protective gloves and clothing Measure Mix Pour Step 1 MEASURE Pour equal parts each of resin and hardener into separate
7. orch over freshly poured Glaze Coat several times until surface is bubble free Be sure to use a waving action so the surface is only slightly warmed allowing remaining air bubbles to disappear Do not hold flame in one area Step 5 Curing To achieve best results apply at temperatures between 70 and 80 F Both Glaze Coat and the item to be coated should be approximately the same temperature NOTE These curing times are to be used as guidelines only Warmer temperatures will yield faster cure times ROOM TEMP DUST FREE PERIOD BETWEEN EACH ADDITIONAL COAT FULL CURE 1 2 coats 4 5 hours a enous 3 coats 24 hours No longer than 48 hours Step 6 Cleanup Use acetone or alcohol for tool and work area cleanup Glaze Coat can only be cleaned while it is still in a liquid state After it has cured paint remover heat gun or sanding is required CAUTION Always use plenty of soap and water to wash skin Additional Information For technical assistance call 800 767 4667 Glaze Coat is heat resistant to approximately 120 F 49 C after fully cured Place some type of protection such as coasters or hot pads when placing hot objects on GLAZE COAT surfaces FAMOWOOD GLAZE COAT is recommended for interior use only and should not be used on hot surfaces such as ash trays or cookware 72 hours When applying GLAZE COAT to large surface areas such as bar tops and table tops special attention to the mixing and applic
Download Pdf Manuals
Related Search