Mighty Mule FM231WB Installation Guide
Contents
1. AA batteries make sure there are no large metal objects or vehicles within 12 feet of the SENSOR replace the AA batteries and allow 60 seconds for it to recalibrate Replace TRANSMITTER batteries when indoor RECEIVER s low battery light comes on In locations where weather varies use Lithium Alkaline AA batteries for best performance NOTE The audible chime will activate once every 15 seconds unless reset button is pressed Is the sensor installed close to driveway as shown Sensor detecting vehicles on the street Is the sensor probe at least 25 feet from the edge of the road Try moving the sensor farther from the road Remember to keep it close to the edge of the driveway e Adjust the sensitivity control to reduce sensitivity Make small changes until street vehicles are not detected Counterclockwise adjustments make the sensor less sensitive Indoor base unit detecting a neighbor s driveway alert e Select a different TRANSMITTER RECEIVER code using the 4 position DIP switch on the transmitter and the indoor unit Both sets of switches must be set exactly the same 6 Wireless Driveway Alarm Instruction Manual 03 04 12 NOTES Wireless Driveway Alarm Instruction Manual 03 04 12 7 FCC WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment In2. accordance with FCC Part 15 Section 15 21 the manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could VOID the user authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in particular installations If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or replace the receiver antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that which the receiver is connected Consult the dealer or an experienced radio TV technician for help GTO Limited One Year Warranty Gates That Open LLC gate openers and accessories are covered under warranty by the manufacturer against defects in materials
3. and manufacturer workmanship for a period of one 1 year from date of purchase provided the recommended installation procedures have been followed In the case of product failure due to defective material or manufacturer workmanship within the one 1 year warranty period the product will be repaired or replaced at the manufacturer s option at no charge to the customer if returned freight prepaid to GTO 3121 Hartsfield Road Tallahassee Florida USA 32303 IMPORTANT Call 800 543 1236 for a Return Goods Authorization RGA number before returning accessory to factory Products received at the factory without an RGA number will not be accepted Replacement or repaired parts are covered by this warranty for the remainder of the one 1 year warranty period or six 6 months whichever is greater GTO will pay the shipping charges equal to United Parcel Service GROUND rate for return to the owner of items repaired under warranty The manufacturer will not be responsible for any charges or damages incurred in the removal of the defective parts for repair or for the reinstallation of those parts after repair This warranty shall be considered void if damage to the product s was due to improper installation or use connection to an improper power source or if damage was caused by electrical power surge lightning wind fire flood insects or other natural agent After the one 1 year warranty period GTO will make any necessary repairs for a
4. full length of signal cable from driveways to prevent false signals the SENSOR to the TRANSMITTER coil the extra cable and bury it beside the transmitter stake ROADWAY For Optimum Performance Locate the SENSOR as far as possible away from power transformers power lines underground gas line and telephone lines Locate the SENSOR away from general moving traffic to prevent unwanted activation Remember that the SENSOR detects MAGNETIC DISTURBANCES caused by a vehicle s mass and velocity Range distance is approximate and will vary due to outside interference type of soil vehicle mass speed etc It is recommended that you run the Signal Cable inside PVC conduit to prevent accidental damage Do not run the Signal Cable in conduit with other wires such as AC power or other control wires The SIGNAL CABLE CANNOT BE SPLICED 2 Wireless Driveway Alarm Instruction Manual 03 04 12 Sensor Placement EA Determining Sensor Location 400 ft Max Wireless IMPORTANT Clear an area 25 ft in all directions of metal tools toys and automobiles to prevent magnetic disturbance during testing and installation e Determine the optimum location for the SENSOR using the information found in Installation DRIVEWAY Overview e Dig a hole approximately 1 ft deep and 1 ft long Signal Cable within 2 ft and parallel to the edge of the driveway ae 12 ft radius max 1 Place the SENSOR flat in
5. nominal fee Call GTO at 800 543 1236 for more information This warranty gives you specific legal rights and you may also have other rights which may vary from state to state This warranty is in lieu of all other warranties expressed or implied NOTE Verification of the warranty period requires copies of receipts or other proof of purchase Please retain these records MUCHII ocd GTO ACCESS MERR SYSTEMS W Gates That Open LLC 3121 Hartsfield Road Tallahassee Florida 32303 www mightymule com www gtoaccess com For online Technical Support visit the Online Troubleshooter Wizard 24 hrs day 7 days week at http support gtoinc com support troubleshooter aspx and open a Tech Ticket Technical Support Hours MON FRI 8 00AM 7 00PM ET 1 800 543 1236
6. Know what s below Calll before you dig Micury ype GIO ACCESS MULE SYSTEMS ACCESS CONTROLS Driveway Alarm INSTALLATION MANUAL Kit Includes A Transmitter D Transformer B Sensor E Mounting post 3 pcs C Receiver How It Works The electromagnetic sensor detects vehicles in motion and sends a signal to the indoor receiver The indoor receiver will chime when it receives the signal www mightymule com www gtoaccess com Gates that Open LLC 3121 Hartsfield Road Tallahassee Florida 32303 1 800 543 GATE 4283 Technical Support 1 800 543 1236 2012 Gates That Open LLC Printed in China for Gates That Open LLC Rev 03 04 12 Installation Overview Place the SENSOR immediately next to the driveway to maximize the sensing range but at least 25 feet from roadways neighbor s driveways or large moving metal objects The cable connecting the SENSOR and TRANSMITTER allows for the placement of the TRANSMITTER away from the driveway in the concealment of landscape or closer to the RECEIVER The approximate transmitting range from the TRANSMITTER to the RECEIVER is 400 ft Range can vary depending on environmental conditions such as RF interference and topography Some adjustment may be required NOTE DO NOT place the TRANSMITTER in the direct path of a sprinkler The TRANSMITTER is water resistant but not waterproof neighbor s If you don t use the
7. ected up to 12 ft from the SENSOR while a small metal object moving slowly might not be detected at the same distance The SENSING RANGE can be adjusted from approximately 5 neighbor s driveways to prevent false signals ROADWAY Sensitivity Adjustment Potentiometer Transmitting LED INSIDE TRANSMITTER SENSITIVITY Oma MIN MAX TRANSMITTING Code Setting DIP Switches BOTTOM OF RECEIVER If you change your DIP switch settings make note here for future reference FACTORY CODE YOUR CODE 0 Troubleshooting System not detecting vehicles e Remove the outer cover from transmitter and check to see if LED blinks when a vehicle passes the sensor The LED indicates that a vehicle was detected and it is transmitting Is the distance to the base unit within the max range of 400 ft Remember that foliage trees and buildings in the line of sight from transmitter to indoor unit will reduce the transmitting range Metal buildings such as mobile homes can block the signal Try placing the indoor unit close to a window facing the outdoor sensor e Kitchen appliances or other electronics may interfere with reception It may be necessary to adjust the position or relocate the RECEIVER for optimum results Are the DIP switches on the indoor and outdoor units both set the same e Make sure receiver volume control is turned up e Remove the
8. nging batteries Bury Sensor 1 ft deep flat and parallel to driveway INSIDE TRANSMITTER 5 Sensitivity 6 AT Adjustment Z Potentiometer TRANSMITTING TRANSMITTER CODE SENSITIVITY Wireless Driveway Alarm Instruction Manual 03 04 12 5 Once the system is tested and working remove the batteries and permanently install the SENSOR SIGNAL CABLE and TRANSMITTER Bury the SENSOR approximately 1 ft deep flat and parallel next to the driveway Dig a narrow trench or slit from the SENSOR to the TRANSMITTER location using a flat spade or other tool The wire from the SENSOR to the TRANSMITTER should be at least six inches deep to avoid possible damage Secure the TRANSMITTER on the supplied 3 piece PVC pipe by burying the bottom third of the pipe in the soil and tamping the ground around the pipe DO NOT cover the TRANSMITTER with a metal cover as this will cause signal interference Secure the TRANSMITTER mounting post in the ground so that the TRANSMITTER is upright and approximately 1 ft above ground Replace the batteries Sensitivity Adjustment a3 to 12 foot radius from the SENSOR The potentiometer varies the sensitivity range of the SENSOR to avoid unwanted moving metal objects from activating the alarm such as moving gates metal play equipment garage doors other vehicular traffic etc With the range adjusted to the maximum of 12 ft a large metal object moving slowly will be det
9. the hole and parallel to SENSOR RANGE X 05 it from gt l neighbor s driveway SENSOR 2 ft from driveway max and 1 ft deep the driveway Keep the SENSOR and the cable uncovered at this time 25 ft from roadway ROADWAY Transmitter Placement Determining Transmitter Location Choose a location for the TRANSMITTER module that is far Connect Sens r Gable enough from the driveway edge that vehicles are unlikely to to Transmitter Module hit it e Run the SENSOR cable through the PVC mounting post and plug it into the connector at the bottom of the Transmitter module K Leave 2 to 3 of slack Leave 2 to 3 of slack in the cable to prevent damage to the in the Sensor Cable connector when the transmitter is removed e Test the chosen location before permanently trenching and setting the TRANSMITTER see Placing Receiver and Testing System section Wireless Driveway Alarm Instruction Manual 03 04 12 3 Installing Transmitter Batteries IMPORTANT AA batteries must be installed at the site where the TRANSMITTER will be located to ensure proper calibration of the transmitter e Make sure the SENSOR wire is plugged into the TRANSMITTER Temporarily place TRANSMITTER on the mounting post in ground e With TRANSMITTER in desired location install two 2 AA batteries Insert AA Batteries Placing Receiver and Testing System Recei
10. ver Placement Place the indoor RECEIVER in a convenient location Plug the AC transformer into a 110 VAC outlet and the charger cable into the receiver POWER LED VISITOR LED LOW BATTERY LED The power LED on the front panel will light up and there will be a confirmation beep tone When acar passes the SENSOR a signal is transmitted to the RECEIVER from the TRANSMITTER After the RECEIVER receives the signal it will chime and the visitor alert LED will turn on and remain lit The LED can be reset by pressing the RESET button but it is not required RESET BUTTON VOLUME CONTROL TRANSFORMER INPUT The LOW BATTERY LED alerts you when the two 2 AA batteries in the outdoor TRANSMITTER need to be replaced Testing the System Test the range and system by having someone drive an automobile past the SENSOR to be sure the RECEIVER is activated when the vehicle has passed the SENSOR Kitchen appliances or other electronics may interfere with reception It may be necessary to adjust the position or relocate the RECEIVER for optimum results See Troubleshooting Section on page 6 4 Wireless Driveway Alarm Instruction Manual 03 04 12 Permanently Install Sensor and Transmitter Transmitter approximately 1 ft above ground Bury any extra wire Edge of Driveway Leave 2 3 inches of wire _ gt slack inside post so the transmitter can be remove without pulling plug loose when cha
Download Pdf Manuals
Related Search