Husky HDK00600SG Use and Care Manual
Contents
1. Clean the air cap Dirt on the left or right side of the fluid tip Clean the fluid tip Heavy spray pattern to the top Dried material at the top or bottom of the Use only non metalic paint or bottom of the paint surface fluid tip Clean the fluid tip The air cap is loose or the seat is dirty Clean and tighten the air cap The air cap is plugged Spray gun emits split spray The fan pattern is open too far Partially close the pattern adjustment pattern The fluid control is turned too far Increase fluid using the fluid control knob Reduce the atomization air pressure The spray gun emits split spray The fan adjustment is partially closed Open the fan pattern adjustment pattern The atomization air adjustment is too high The paint material is too thick Thin paint material to proper viscosity Atomization presure is too low Increase the atomization pressure o Dry or loose fluid needle packing nut o Lubricate and tighten the fluid needle and packing nut o The air vent is clogged o Clear the vent hole The spray gun emits excessive m The atomization pressure is set too high o Reduce the atomization pressure eee o The spray gun is held too far away from the o Adjust to the proper distance work surface o Improper stroking arcing gun motion too o Move the spray gun at a moderate fast pace parallel to the surface The spray gun will not spray o There is no air pressure at the gun o Check the air l2. Maintenance Ensure the air line is shut off and drained of air before removing this tool for service This will prevent the tool from operating if the throttle is accidentally engaged DAILY CLEAN UP ri NOTE Clean the spray gun immediately after use o Remove and empty the canister Rinse with a solvent recommended for the paint or other material used Refill the canister with clean solvent and attach to the gun Spray the solvent through the gun while shaking the gun vigorously Wipe the gun exterior with a solvent soaked rag Repeat until the gun is clean m Remove the air cap and soak in solvent until clean Use a small brush for stubborn stains if necessary Toothpicks or small brushes may be used to clean air passages NEVER USE METAL OBJECTS TO CLEAN PRECISELY DRILLED PASSAGES DAMAGED PASSAGES WILL CAUSE IMPROPER SPRAYING o Clean the gaskets with a solvent soaked rag To prevent equipment damage DO NOT IMMERSE THE GASKET OR SPRAY GUN BODY IN SOLVENTS o After using water to clean out water based paints or materials spray mineral spirits through the gun to prevent corrosion o Use anon silicone oil on all moving parts when reassembling Use Vaseline or light grease on all threaded connections prior to storage Troubleshooting Possible Cause Solution S Heavy spray pattern to the left o Holes in the left or right side of the air cap Use only non metalic paint or right of the paint surface are plugged
3. ines o The fluid control is not open enough o Open fluid control o The material is too heavy m Thin the material or change over to a pressure feed system 9 HUSKYTOOLS COM Please contact 1 888 43 HUSKY for further assistance Service Parts 745 miti Oe I 6 y C 10 18 437 47 Ta ii e 15 34 qi Cp 35 33 10 Service Parts continued Reference Part Number Description Number 1 a arcara ia e0218 aircap tem 2 men arcon a eBoeose114 noze tam a eBoe03B118 Noze 1 8mm 5 enosoe4 Pattern Control Neede e enososs Patter ControiNut 7 fm om a enosoe5 Patter Controlo o oweos eune o owna Air Vaive Copper aroma airvalve Packing Ring 2 a a as 16 Air Valve Needle 9W7133 Air Valve Bushing 9W7115 Air Valve Spring 9W98043 9H98041 Fluid Needle Seat 18 LB 19a 9H9809C_ Fluid Adj Needle 1 8mm 20 9H98081 Fluid Adj Gasket 2 i 2 9H98042 Fluid Needle Packing 9H9809B Fluid Adj Needle 1 4 mm 9H9808 Fluid Valve Bushing 9H9810 Fluid Adj Spring 11 Number wmm arme jowri22 wasr owo O Ring Hos fwase 9W9801 1 3 23 21 30 31 32 33 34 35 36 37 7a 38 39 43 HUSKYTOOLS COM Please contact 1 888 43 HUSKY for further assistance
Download Pdf Manuals
Related Search