Florida Pneumatic FP-780 Use and Care Manual
Contents
1. A PLEASE READ AND FOLLOW ALL WARNINGS A Fiz ATIC FP 780 ENGRAVING PEN Read Operating Instructions Always become familiar with all the instructions and warnings before operating any power tool Always Wear Approved Eye Protection Impact resistant eye protection should meet or exceed the standards as set forth in the United States ANSI Z87 1 Occupational and Educational Eye and Face Protection Look for the marking Z87 1 on your eye protection to insure that it is an approved style For further information ANSI Z87 1 Occupational and Educational Eye and Face Protection is available from the American National Standards Institute Inc 11 West 42nd Street New York NY 10036 Hearing Protection is Recommended Hearing protection should be used when the noise level exposure equals or exceeds an 8 hour time weighted average sound level of 85 dBA Process noise reflective surfaces other tools being operated nearby all add to the noise level present in your work area If you are unable to determine your noise level exposure we recommend the use of hearing protection Avoid Prolonged Exposure to Vibration Tools can vibrate during use Prolonged exposure to vibration or very repetitive hand and arm movements can cause injury Stop using any tool if discomfort tingling feeling or pain occurs You should consult your physician before resuming use of the tool 90 PSIG Maximum This tool is designed to oper2. instructions for future reference devices as furnished by the manufac turer Where an air tool is modified or altered the modifier shall provide the safeguards to enable it to be safely used in the operations intended and to comply with any applicable provisions as contained in ANSI B186 1 Tool Installation Pressure regulators shall be used to limit air pressure to the rated pressure where the supply pressure exceeds the tool s rated pressure Air hoses and lines shall be relieved of compressed air before being disconnected or disjointed unless there is automatic valve closing protec tion at the joint being separated Syn thetic lubricants which can cause deterioration of elastomer seals shall not be used in air systems of air tools Tool Maintenance It shall be the tool owner s and or employer s responsibility to assure that tools are maintained in a safe operating condition Tool maintenance and repair shall be performed by authorized trained competent personnel Tools shall be disconnected from their compressed air supply before repairs are attempted Repairs shall be consistent with the manufacturer s recommended proce dures Tool hoses and fittings shall be replaced if unsuitable for safe operation It shall be the tool owner s and or employer s responsibility to keep required rating markings and warnings on the tool in legible condition PL 0139 FL RIDA jii FL RIDA ji TIC ENGRAVING PEN MA
3. TIC ENGRAVING PEN Specifications Replacement Parts for FP 780 Ref Description Part Ref Description Part 1 Hose Fitting 9780001 8 Rubber Seat 9780008 2 Hose Clamp 9780002 9 Steel Ball 9780009 3 Hose 5 ft 9780003 10 Front Housing 9780010 4 On Off Knob 9780004 11 Engraving Pin 9780011 5 O Ring 9780005 W Spring 6 Set Screw 9780006 12 Stop Washer 9780012 7 Back Housing 9780007 13 Rubber Sleeve 9780013 14 Nose Cone 9780014 Florida Pneumatic s Limited Warranty Florida Pneumatic warrants their tools to be free from defects in material and workman ship for one year from the date of purchase This warranty does not apply to tools which have been abused misused modified or repaired by someone other than Florida Pneumatic or their authorized service centers If a Florida Pneumatic tool proves defective in material or workmanship within one year after purchase return it to any authorized service center or Florida Pneumatic freight prepaid Please enclose your 12 14 name address and adequate proof of purchase and a short description of the defect Florida Pneumatic will at their option repair or replace defective tools free of charge Repairs or replacements are warranted as described above for the remainder of the Original warranty period Florida Pneumatic s sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool There are no other warranties expressed or implied and Florid
4. a Pneumatic shall not be liable for incidental consequential or special damages or any other damages costs or expense of repair or replacement as described above
5. ate at 30 psig an air pressure of 90 pounds per square inch gauge pressure 90 PSIG maximum at the tool Use of higher air pressure can and may cause injury Also the use of higher air pressure places the internal components under loads and stresses they were not designed for causing premature failure The air supply should be clean and dry preferably lubricated For best results drain the moisture from your compressor WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to cause cancer birth defects or reproductive harm Some examples of these chemicals are e Lead from lead based paints e Crystalline silica from bricks cement and other masonry products e Arsenic and chromium from chemi cally treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles KN More than 1 100 slope KN a See a oT TY Filter Main line 3 times LI Branch line 2 times Stop Tool inlet hose size Tool inlet hose size Regulator Lubricator Valve H h i M Auto Drain door Air Compressor m Valve i LT Florida Pneumatic Air Tools A Division of Florida Pneumatic Manufacturing Cor
6. poration 851 Jupiter Park Lane Jupiter Florida 33458 Rev 11 98 561 744 9500 Fax 561 575 9134 Toll Free 1 800 327 9403 Description The Florida Pneumatic Engraving Pen is designed for engraving on hardened steel aluminum and glass wae Safety Instructions The following instructions are furnished as general guidelines for use of your pneumatic tool They cannot compre hensively cover all possible or conceiv able uses of the subject tool For additional information on the safe use of air tools we advise you to obtain a copy of ANSI B186 1 Safety Code for Portable Air Tools available from the following source American National Standards Institute Inc 11 West 42nd Street New York NY 10036 The use of the word shall in the following instructions indicates that adherence to the particular require ment is necessary to conform to ANSI B186 1 Tool Application and Usage Portable tools shall be used only for the purposes intended in their design and within the capacity for which they were intended and rated It shall be the tool owner s and or employer s responsibility to instruct each operator in the safe use of the tool Tools shall not be used without guards and safety Read these instructions carefully before attempting to install operate or service this Florida Pneumatic product Failure to comply with the instructions could result in personal injury and or property damage Retain these
Download Pdf Manuals
Related Search