Florida Pneumatic FP-711A Use and Care Manual
Contents
1. 18 9ST70018 PIN 2 39 935039A SCREW 1 19 920019 ROTOR BLADE 4 40 935040A DIE 1 20 935020 ROTOR 6T 1 41 935041 NUT 1 21 9ST70021 CYLINDER 1 Limited Warranty Florida Pneumatic warrants its tools to be free from defects in material and workmanship for two years from the date of purchase This warranty does not apply to tools which have been abused misused modified or repaired by someone other than Florida Pneumatic or its authorized service centers If a Florida Pneumatic proves defective in material of workmanship within one year after purchase return it to any authorized service center or to Florida Pneumatic freight prepaid Please enclose your name address and adequate proof of purchase date with a brief description of the defect Florida Pneumatic will at its option repair or replace defective tools free of charge Repairs or replacements are warranted as described above for the remainder of the warranty period Florida Pneumatic s sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool There are no other warranties expressed or implied and Florida Pneumatic shall not be liable for incidental consequential or special damages or any other damages costs or expense of repair or replacement as described above2. relieved of compressed air before being disconnected or disjointed unless there is automatic valve closing protec tion at the joint being separated Syn thetic lubricants which can cause deterioration of elastomer seals shall not be used in air systems of air tools Tool Maintenance It shall be the tool owner s and or employer s responsibility to assure that tools are maintained in a safe operating condition Tool maintenance and repair shall be performed by authorized trained competent personnel Tools shall be disconnected from their compressed air supply before repairs are attempted Repairs shall be consistent with the manufacturer s recommended proce dures Tool hoses and fittings shall be replaced if unsuitable for safe operation It shall be the tool owner s and or employer s responsibility to keep required rating markings and warnings on the tool in legible condition Read these instructions carefully before attempting to install operate or service this Florida Pneumatic product Failure to comply with the instructions could result in personal injury and or property damage Retain these instructions for future reference FP 711A AIR TOOLS FP 711A Air Nibbler Air Nibbler OSS TOG MUM a a a A A A E E A E AE E EE TEA 2 600 Maxi Replacement Parts for FP 711A IRIE CAD ACM rep 16 gauge steel ne Width Of CUt esssccccscsssssseessssssssssssssesssssssssseessssessussesssssseseessensesususssssssseeeeeee 3
3. 16 4 5mm eee oY eee ee ony B l l l 1 9ST70001 SCREW 1 22 970022A CONE MUFFLER 1 Minimum Gutmng TadiUS csser a 1 3 s Dia 2 9ST70002 O RING P12 1 23 9ST70023 FRONT PLATE 1 hh Col E g EEE een ee A E a eee en ER A Re eee ere ee 2 a bs 3 9ST70003 O RING P8 2 24 970024A BEARING 608ZZ 1 Lono iliac ise vee datas A pis raceredataadeaiesrusatpiestoesiablaiciaseiedsinateaiainaans 7 2 95170004 AIR REGULATOR 1 25 935025 WASHER _ _ 1 l 5 950332 SPRING 1 26 935026 THREAD RING GEAR 42T 1 Average air CONSUMPTION cccccccccssssssceeesssseeeesssssseeeeeesssseseeeessssseeeeeesesseeseess 4 CFM 6 970429 VALVE STEM BUSHING 1 27 924527 IDLER GEAR 18T 3 Recommended NOSE SIZE ceeeccccccccccccsseeeeeeeeeeeecececeeeeuseuueeuueeeuuuaeeeeseeeeeeeneeeeeees 3 8 I D 7__9ST70007 VALVE STEM 1 28 9ST70028 IDLER GEAR PIN 3 a E PNA A AAA E A E E E 1 4 NPT 8 20891 O RING 3 5 1 4 1 29 920325 2 GEAR PLATE 1 l 9 9ST70009 AIR INLET 1 30 935030 CLAMP NUT 1 Maximum operating POSSUIe cccccccessccccceessssseeeeeeeseseseeeeeessseeeeeeessesssaeeeees 90 PSI 10 9ST70010A EXHAUST SLEEVE 1 31 924531 BEARING 6200ZZ 5 Parts Breakdown for FP 711A 11 9ST70011 O RING 26 7 1 78 1 32 920117 CRANK SHAFT 1 12 970432 SPRING PIN 1 33 920118 CAM 1 13 970013BK LEVER 1 34 920119 HEAD CAP 1 14 _9ST70014 RUBBER 1 35 920120 BUSHING 1 15 9ST70015 HOUSING 1 36 920121 HEAD 1 16 920312 BEARING 696ZZ 1 37 920122 SLIDE SPINDLE 1 17 9ST70017 REAR PLATE 1 38 935038A PUNCH 1
4. AX PLEASE READ AND FOLLOW ALL WARNINGS 30 psig Read Operating Instructions Always become familiar with all the instructions and warnings before operating any power tool Always Wear Approved Eye Protection Impact resistant eye protection should meet or exceed the standards as set forth in the United States ANSI Z87 1 Occupational and Educational Eye and Face Protection Look for the marking Z87 1 on your eye protection to insure that it is an approved style For further information ANSI Z87 1 Occupational and Educational Eye and Face Protection is available from the American National Standards Institute Inc 11 West 42nd Street New York NY 10036 Hearing Protection is Recommended Hearing protection should be used when the noise level exposure equals or exceeds an 8 hour time weighted average sound level of 85 dBA Process noise reflective surfaces other tools being operated nearby all add to the noise level present in your work area If you are unable to determine your noise level exposure we recommend the use of hearing protection Avoid Prolonged Exposure to Vibration Tools can vibrate during use Prolonged exposure to vibration or very repetitive hand and arm movements can cause injury Stop using any tool if discomfort tingling feeling or pain occurs You should consult your physician before resuming use of the tool 90 PSIG Maximum This tool is designed to operate at an air p
5. ressure of 90 pounds per square inch gauge pressure 90 PSIG maximum at the tool Use of higher air pressure can and may cause injury Also the use of higher air pressure places the internal components under loads and stresses they were not designed for causing premature failure The air supply should be clean and dry preferably lubricated For best results drain the moisture from your compressor daily WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to cause cancer birth defects or reproductive harm Some examples of these chemicals are e Lead from lead based paints e Crystalline silica from bricks cement and other masonry products e Arsenic and chromium from chemi cally treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles Main 3 times ain line Tool inlet hose size Florida Pneumatic Manufacturing Corporation 851 Jupiter Park Lane Jupiter Florida 33458 Toll Free 1 800 327 9403 AIR TOOLS Description FP 711A Air Nibbler Florida Pneumatic air nibbler weights two pounds but can cuts through mild steel without deforming or burring metal Cut
6. s around templates with ease Safety Instructions The following instructions are furnished as general guidelines for use of your pneumatic tool They cannot compre hensively cover all possible or conceiv able uses of the subject tool For additional information on the safe use of air tools we advise you to obtain a copy of ANSI B186 1 Safety Code for Portable Air Tools available from the following source American National Standards Institute Inc 11 West 42nd Street New York NY 10036 The use of the word shall in the following instructions indicates that adherence to the particular require ment is necessary to conform to ANSI B186 1 Tool Application and Usage Portable tools shall be used only for the purposes intended in their design and within the capacity for which they were intended and rated It shall be the tool owner s and or employer s responsibility to instruct each operator in the safe use of the tool Tools shall not be used without guards and safety devices as furnished by the manufac turer Where an air tool is modified or altered the modifier shall provide the safeguards to enable it to be safely used in the operations intended and to comply with any applicable provisions as contained in ANSI B186 1 Tool Installation Pressure regulators shall be used to limit air pressure to the rated pressure where the supply pressure exceeds the tool s rated pressure Air hoses and lines shall be
Download Pdf Manuals
Related Search