Kawasaki 841270 Use and Care Manual
Contents
1. Outer Flange COMPONENT MODEL NUMBER WRENCH 690157 11 Wrench DO gt W 10 10 Grinding Wheel ASSEMBLY CAUTION Make sure you have full control of the tool when grinding into a corner as a sharp sudden movement may occur when the wheel contacts a secondary surface ATTACHING AUXILIARY HANDLE This tool comes with an auxiliary handle which can be attached to either side of the Angle Grinder depending on the preference of the operator This handle is necessary to maintain complete control of the tool and should be used at all times Make sure this handle is always fastened securely LEFT HANDLE ATTACHING WHEELS WITH DEPRESSED CENTERS 4 WARNING Always check the tool warning label for the recommend ed speed rating on accessories Never run a wheel or brush over the rated speed Accessories exceeding the recommended speed may fly apart and cause serious personal injury NOTE Hubhed wheels do not require mounting flanges 1 Check to make sure that the guard is fitted properly Put the inner flange on lt the spindle 2 Put the grinding wheel on the spindle and GRINDING the inner flange WHEEL When working with thin grinding wheels gt fit the threaded outer flange with the FLANGE raised area facing toward the wheel OUTER FLANGE 4 When working with thick grinding wheels fit the threaded outer flange with the raise2. 16 16 16 16 8 10 16 16 16 14 10 12 16 16 14 14 12 16 14 12 12 16 20 12 12 12 14 SPECIFICATIONS SPECIFICATIONS Voltage 120V 60 Hz Rated Current 6 0 A No Load Speed 10 500 min Maximum Disc Diameter 115mm 4 1 2 in OTHER CONSUMER DO IT YOURSELF DIY TOOLS Alltrade offers a full range of Kawasaki tools that make DIY jobs easy If you would like further information on the following products please contact Alltrade Customer Service Department at 1 800 590 3723 Cordless Drills Screwdrivers Impact Wrenches Sanders Jigsaws Circular Saws Angle Grinders Reciprocating Saws Routers Rotary Tools Corded and Cordless Multi Purpose Tools Wide Range of Accessories and more 15 3 YEAR WARRANTY Express and Exclusive Limited Home Use Warranty to Original Retail Buyer Alltrade Tools LLC hereinafter Alltrade expressly warrants to the original retail purchaser of the accompanying KAWASAKI portable power tool and no one else all parts of the product except those parts referred to below which are specifically excluded from such warranty see Exclusions to be free from defects in materials and workmanship for a period of three years from original date of purchase SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS This Kawasaki portable power tool is offered as a home use tool and carries a HOME USE WARRANTY This tool is made for home use in the execution of projects and repairs in and around the home U
3. AND OR SYMBOLS 6 8 SAFETY RULES FOR ANGLE GRINDERS 6 8 SYMBOLS Pu 9 SECTION THREE FUNCTIONAL DESCRIPTION 10 ASSEMBLY 11 12 ATTACHING AUXILIARY HANDLE 11 ATTACHING WHEELS WITH DEPRESSED CENTERS 11 12 ATTACHING WIRE BRUSHES 12 12 REMOVING GUARD FOR SANDING OR FLAT WIRE BRUSHES 12 ATTACHING SANDING 015 12 OPERATING THE ANGLE GRINDER ng 13 OPERATING THE ON OFF SWITCH 13 SECTION FOUR MAINTENANCE AND CLEANING 14 RUGESBSDBIES 14 SPEGIFIGATIORNS dd eur o bh Br 15 OTHER CONSUMER DO IT YOURSELF DIY TOOLS 15 SECTION FIVE YEAR LIMITED WARRANTY n 16 19 CONGRATULATIONS Thanks for choosing this product At Alltrade our aim is to provide you with quality products at an affordable price and we want you to be totally satisfied with your product and our Customer Service If any help and advice is needed please contact us at 1 800 590 3723 Properly cared for this tool will give you many years of satisfaction INTENDED USE This tool is intended for consumer use only This tool is not designed for profes si
4. During the warranty period Alltrade will be responsi ble for the return shipping charges Alltrade s repair and or replacement of any non conforming item and or part thereof shall constitute fulfillment of all obligations to the purchaser Alltrade shall not be responsible or liable for any expense including freight charges or repairs made outside Alltrade s facility unless expressly agreed to by Alltrade in writing Under no circumstances shall Alltrade bear any responsibility for loss of the unit loss of time or rental inconvenience commercial loss or consequential damages Exclusions This warranty does not cover parts damaged due to normal wear abnormal conditions misapplication misuse abuse accidents operation at other than recommended pressures or temperatures improper storage or freight damage Parts damaged or worn by operation in dusty environments are not warranted Failure to follow recommended operating and maintenance procedures also voids warranty This limited warranty does not apply to accessory items such as drill bits screwdriving bits circular saw blades jigsaw blades grinding wheels sanding sheets and other related items DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING ACCIDENT ABUSE NEGLIGENCE FAILURE TO FOLLOW INSTRUCTIONS UNAUTHORIZED REPAIRS OR ALTERATIONS DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES COMMERCIAL AND RENTAL APPLICATION
5. D HEREUNDER EVEN IF ALLTRADE AND OR ITS REPRESENTATIVE S HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES IN NO EVENT WHETHER AS A RESULT OF A BREACH OF CONTRACT WARRANTY TORT INCLUDING NEGLIGENCE OR OTHERWISE SHALL 18 ALLTRADE S AND OR ITS REPRESENTATIVE S LIABILITY EXCEED THE PRICE OF THE PRODUCT ANY AND ALL LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIODS SPECIFIED ABOVE Limitations on Warranty Disclaimers Some states do not allow limitations on how long an implied warranty lasts and some states do not allow the exclusion or limitation of the incidental or consequential damages so part or all of the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state If your product is not covered by this warranty please call our Customer Service Department toll free at 1 800 590 3723 for general repair information and charges 19 20
6. FOR CUSTOMER SERVICE POUR LE SERVICE APRES VENTE OU DU CONSOMMATEUR PARA EL SERVICIO PARA EL CONSUMIDOR 1 800 590 3723 Printed in China Imprim dans la Chine Impreso en China OFFICIAL LICENSED PRODUCT 87 1904 60957 KAWASAKI IS A TRADEMARK LICENSED BY KAWASAKI MOTORS CORP U S A WHICH DOES NOT MANUFACTURE OR DISTRIBUTE THIS PRODUCT CONSUMER INQUIRES SHOULD BE DIRECTED TO KAWASAKI EST UNE MARQUE DE COMMERCE DE KAWASAKI MOTORS CORP U S A QUI NE FABRIQUE PAS ET NE DISTRIBUE MATEURS DOIVENT ETRE ADRESSEES A KAWASAKI ES UNA MARCA REGISTRADA CON LICENCIA DE KAWASAKI MOTORS CORP E U A QUE NO FABRICA NI DISTRIBUYE ESTE PRODUCTO LAS CONSULTAS DE LOS CONSUMIDORES DEBEN DIRIGIRSE A COPYRIGHT 2009 ALLTRADE TOOLS LLC 1431 VIA PLATA LONG BEACH CA 90810 1462 USA 691600 4 1 2 in Angle Grinder Meuleuse angulaire de 4 1 2 po Esmeriladora angular de 4 1 2 in Rev 3 2 09 COMPOSANT COMPONENTE PAS CE PRODUIT THIS PRODUCT LES QUESTIONS DES CONSOM COMPONENT 691600 4 1 2 IN ANGLE GRINDER INSTRUCTION MANUAL MANUEL D UTILISATION DE LA MEULEUSE D ANGLE DE 4 1 2 PO MANUAL DE INSTRUCCIONES PARA LA ESMERILADORA ANGULAR DE 4 1 2 PULG THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THIS PRODUCT BEFORE USE READ CAREFULLY AND UNDERSTAND ALL CAUTIONS WARNINGS INSTRUCTIONS AND PRODUCT LABELS FAILURE TO DO SO COULD RESULT IN SER
7. IOUS PERSONAL INJURY AND OR PROPERTY DAMAGE CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA S CURIT LE FONCTIONNEMENT ET LE REMISAGE DE CE PRODUIT LIRE TUDIER ET VEILLER BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS ET AUTOCOLLANTS APPOS S SUR LE PRODUIT AVANT DE L UTILISER NE PAS RESPECTER CES INSTRUCTIONS POURRAIT ENTRAINER DES BLESSURES ET OU DES DOMMAGES MAT RIELS ESTE MANUAL CONTIENE INFORMACI N IMPORTANTE SOBRE LA SEGURIDAD OPERACI N MANTENIMIENTO Y ALMACE NAMIENTO DE ESTE PRODUCTO ANTES DE USARLO LEA Y COMPRENDA TODAS LAS PRECAUCIONES ADVERTENCIAS NSTRUCCIONES Y ETIQUETAS DEL PRODUCTO DE LO CONTRARIO PODRIA SUFRIR LESIONES GRAVES 0 CAUSAR DANOS MATERIALES F YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1 800 590 3723 BEFORE YOU CALL HAVE THE FOLLOWING INFORMATION AVAILABLE MODEL No DATE PURCHASED AND STORE LOCATION AN ALLTRADE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE IF YOU WOULD LIKE TO MAKE A SUGGESTION OR COMMENT GIVE US A CALL OR EMAIL US AT INFO ALLTRADETOOLS COM YOUR FEEDBACK IS VITAL TO US POUR TOUTE QUESTION OU EN CAS DE PROBLEME AVEC LE PRODUIT ALLTRADE NE PAS LE RETOURNER AU MAGASIN OU IL A T ACHET APPELER LE SERVICE APRES VENTEAU 1 800 590 3723 AVANT D APPELER VEILLER A SE PROCURER LES NFORMATIONS SUIVANTES No DE MODELE DA
8. S OR OTHER CAUSES UNRELATED TO PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS WARRANTY Alltrade will not be liable for the following labor charges loss or damage resulting from improper operation maintenance or repairs made by other persons pre delivery services such as assembly oil or lubricants and adjustment maintenance services that are normally required to maintain the product The use of other than genuine Alltrade Repair Parts will void warranty Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS EXCEPT FOR THE LIMITED WARRANTY 17 PROVIDED ABOVE ALL OTHER EXPRESS WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE BUYER ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES INCLUDING THE IMPLIED WARRAN
9. TE DE LACHAT ET ADRESSE DU MAGASIN UN REPR SENTANT D ALLTRADE PEUT R SOUDRE VOTRE PROBLEME PAR T L PHONE POUR TOUT COMMENTAIRE OU SUGGESTION N H SITEZ PAS NOUS APPELER OU NOUS CONTACTER PAR COURRIEL A L ADRESSE INFO ALLTRADETOOLS COM VOS COMMENTAIRES NOUS SONT EXTR MEMENT PR CIEUX SI TIENE DUDAS 0 SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1 800 590 3723 ANTES DE LLAMAR TENGA A MANO LA SIGUIENTE INFORMACI N No DE MODELO FECHA DE COMPRA Y DIRECCI N DE LA TIENDA UN REPRESENTANTE DE ALLTRADE PUEDE RESOLVER SU PROBLEMA POR TEL FONO SI DESEA HACER ALGUNA SUGERENCIA 0 COMENTARIO LL MENOS 0 ENV ENOS UN MENSAJE DE CORREO ELECTR NICO A INFOGALLTRADETOOLS COM SUS COMENTARIOS SON FUNDAMENTALES PARA NOSOTROS TABLE OF CONTENTS CONGRATULATIONS 2 INTENDED USE oc sonia ites ett ox any dered ase ie ore 2 SECTION ONE GENERAL SAFETY RULES FOR ALL ELECTRIC POWER TOOLS 2 6 RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS 2 3 IMPORTANT SAFEGUARDS 3 WORK CPRIER eases Drac aec 4 ELECTRICAL SAFETY oues adea icai ir e ilem cus 4 PERSDIAL SAPE FI aue iba diae sette to bres 5 TOOL USE AND CARE 5 6 SERVIO rM E state E E 6 SECTION TWO SPECIFIC SAFETY RULES
10. TIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE NO WARRANTY ORAL OR WRITTEN OTHER THAN THE ABOVE WARRANTY IS MADE WITH REGARD TO THIS PRODUCT ALL EXPRESS AND OR IMPLIED WARRANTIES GUARANTIES AND OR REPRESENTATIONS BY ALLTRADE AND OR ITS REPRESENTATIVE S REGARDING THE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF THE PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER REGARDLESS OF WHETHER ANY SUCH WARRANTY GUARANTY AND OR REPRESENTATION WRITTEN OR ORAL ARISES BY OPERATION OF LAW AND OR EQUITY AND OR BY ANY ACT OR OMISSION OF ALLTRADE AND OR ITS REPRESENTATIVE S OR THE PURCHASER INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE AND OR ITS REPRESENTATIVES PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS CLAIMS AND OR CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON PURCHASER S SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE Limitation Of Liability IN NO EVENT SHALL ALLTRADE AND OR ITS REPRESENTATIVE S BE LIABLE FOR INDIRECT INCIDENTAL SPECIAL AND OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF OR RELATED TO DIRECTLY OR INDIRECTLY ANY BREACH OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND OR ITS REPRESENTATIVE S AND PURCHASER ANY WARRANTY HEREUNDER AND OR THE EXISTENCE DESIGN MANUFACTURE PURCHASE USE AND OR OPERATION OF ANY ITEM S SOL
11. d area facing away from the wheel 5 Push in the spindle lock button Turn the outer flange until it locks into place 6 Once the spindle is locked insert the enclosed wrench into the holes of the outer flange to tighten the outer flange properly ATTACHING WIRE BRUSHES Wire cup brushes not included can be screwed directly on the spindle No flanges are necessary o EDGE GRINDING 757 WARNING po not use edge grinding wheels for cut off work deep grinding or subject them to any side pressure as this may lead to breakage and possible personal injury These wheels should be used for shallow cutting and notching less than 1 2 inch in depth Keep the open side of the guard away from the operator at all times Edge grinding should only be done with wheels specifically designed for this purpose REMOVING GUARD FOR SANDING OR USING FLAT WIRE BRUSHES Set the Angle Grinder on a flat surface with the spindle facing up Remove the inner and outer flanges unscrew spring washer and remove the guard co Store these parts carefully Replace the guard after the job is finished ATTACHING SANDING DISC To remove the guard see instructions given in the Removing Guard for Sanding or Using Flat Wire Brushes Section above Po Rotate sanding disc on to the spindle co Push in the spindle lock button Turn the spindle until it locks into place Once the spindl
12. des additional information that is useful for proper use and maintenance of this tool If a NOTE is indicated make sure it is fully understood IMPORTANT SAFEGUARDS DANGER People with electronic devices such as pacemakers should consult their physician s before using this product Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm Some examples of these chemicals are Lead from lead based paints e Crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as dust masks that are specially designed to filter out microscopic particles WARNING This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm WARNING Keep your work area clean and well lit Cluttered work benches and dark work areas may cause accidents or injury Do not operate power tools in explosive areas such as in the prese
13. e Angle Grinder always maintain a firm grip on the tool Keep your hands well away from the grinding wheel or brush Never reach under neath the Angle Grinder while sanding disk is in motion When the Angle Grinder is in operation keep hands away from the cutting or grinding area CAUTION Do not run the Angle Grinder while carrying it at your side A moving grind ing wheel or brush could cause lacerations or personal injury The disc will not stop immediately when the Angle Grinder is turned off Exercise caution Do not set the Angle Grinder down after use until the grinding or cutting wheels have come to a complete stop Keep the handle of the Angle Grinder dry clean and free from oil and grease Unplug Angle Grinder from power supply and place the switch in the locked or OFF position before making any assembly adjustments changing accessories or performing any inspection maintenance or cleaning proce dures Such preventive safety measures reduce the risk of starting the tool acci dentally which could cause serious personal injury Only use grinding and cutting wheels that are approved for a maximum speed of 13 000 RPM or greater After replacing a wheel or brush always let the tool run for one minute in a well protected area If the new accessory has an undetected flaw it should break apart in less than a minute Do not use the Angle Grinder if it has been damaged left outdoors in the rain snow wet or damp
14. e is locked tighten the sanding disc by hand 12 OPERATING THE ANGLE GRINDER 4 WARNING Always unplug the tool before attempting to change the guard or accessories MAINTENANCE AND CLEANING WARNING Always UNPLUG the tool from the power source before cleaning or maintenance NOTE For best tool control material removal and minimal loading keep the angle between the disc and the work surface at approximate ly 30 when grinding and 10 15 when sanding OPERATING THE ON OFF SWITCH WARNING Never switch the Angle Grinder ON or OFF while under load conditions CAUTION Always allow the Angle Grinder to come up to full speed before touching any surface Always take the tool away from the workpiece before turning the tool OFF Let the tool come to a complete stop before setting it down This tool operates best under light pressure Exerting heavy pressure will not speed up the work and may cause damage to the motor 1 When starting hold the Angle Grinder firmly with both hands One hand on the rear handle or the motor housing and the other hand on the side handle 2 To turn the Angle Grinder ON without locking it apply forward pressure to the rear of the ON OFF switch When pressure is released the switch snaps to the OFF position 3 The switch can be locked in the ON position a convenience for long grinding operations To lock the switch ON firmly pr
15. environments or immersed in liquid Maintain labels and nameplates on the Angle Grinder These carry important information If unreadable or missing contact Alltrade for a replacement Accessories must be rated for at least the speed recommended on the tool warning label Wheels and other accessories running over rated speed can fly apart and cause injury SYMBOLS IMPORTANT Some of the following symbols may be used on your tool Please study them and learn their meaning Proper interpretation of these symbols will allow you to operate the tool better and safer SYMBOL V A Hz min 1 2 3 NAME Volts Amperes Hertz Watt Kilograms Alternating Current Direct Current Alternating or Direct Current Earthing Terminal Class 11 Construction Minutes Seconds Diameter No load speed Revolutions per Minute Ring Selector Settings EXPLANATION Voltage Potential Current Frequency Cycles per Second Power Weight Type of Current Type of Current Type of Current Grounding Terminal Denotes Double Insulation Time Time Size of Drill Bits Grinding Wheels etc No load Rotational Speed Revolutions Surface Speed Strokes etc per Minute Speed Torque or Position Settings FUNCTIONAL DESCRIPTION CONTROLS AND COMPONENTS ACCESSORIES Spindle Lock Button Spindle Wheel Guard Motor Housing ON OFF Paddle Switch Electrical Cord Auxiliary Handle Inner Flange
16. ess forward the rear of the switch and then press down the front to lock the tab inside the notch on the body of the grinder 4 To unlock the switch simply press the rear of the switch The switch is spring loaded and will snap back automatically 13 Use compressed air to blow out any accumulated dust or grit Tiny particles from metal grinding often accumulate inside your tool and could create an electrical shock hazard Never use solvents or harsh chemicals Use only mild soap and a damp cloth to clean the tool Never let any liquid get inside the casing Never immerse any part of the tool in a liquid Always keep the ventilation openings clear Regularly clean the ventilation slots in your tool using a soft brush or dry cloth Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Always attach grounded 3 prong extension cords to grounded 3 hole outlets If you must use an extension cord be sure that the gauge is large enough to carry the amount of current necessary for your power tool If not your tool may experi ence a loss of power excessive voltage drop or overheating The smaller the gauge number the heavier the cord see table below RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING CONDUCTOR SIZE IN A W G AMPERE 10FT 25FT 50FT 100FT 3 6 16 16 16 16 6 8
17. marked W A or W These cords are rated for outdoor use and reduce the risk of electric shock PERSONAL SAFETY 4 WARNING Stay alert watch what you are doing and use common sense when operat ing a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Avoid accidental starting Be sure switch is off before plugging in Carrying tools with your finger on the switch or plugging in tools that have the switch on invites accidents Remove adjusting keys or wrenches before turning the power tool ON A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times Proper foot ing and balance enables better control of the power tool in unexpected situa tions Use safety equipment Always wear eye protection Dust mask non skid safe ty shoes hard hat or hearing protection must be used for appropriate conditions TOOL USE AND CARE CAUTION Use clamps or other practical ways to secure and support the workpiece to a stable platform Holding the work by hand or against your body is uns
18. nce of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control ELECTRICAL SAFETY WARNING Double insulated tools are equipped with a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install a polarized outlet Do not change the plug in any way Double insulation 5 eliminates the need for the three wire grounded power cord and grounded power supply system Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord to carry the tool or pull the plug from an outlet Keep the cord away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords increase the risk of electric shock Keep cord away from heat oil sharp edges or moving parts Replace dam aged cords immediately Damaged cords increase the risk of electric shock When operating the power tool outside use an outdoor extension cord
19. onal use The power cord should only be used in approved electrical outlets as described in this manual GENERAL SAFETY RULES FOR ALL ELECTRIC POWER TOOLS 4 WARNING READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE RECOGNIZE SAFETY SYMBOLS WORDS AND LABELS The safety instructions provided in this manual are not intended to cover all possible conditions and practices that may occur when operating maintaining and cleaning power tools Always use common sense and pay particular attention to all the DANGER WARNING CAUTION and NOTE statements of this manual A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious injury DANGER A WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury A CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury CAUTION used without the safety alert symbol indicates a potentially hazardous situation which if not avoided may result in property damage NOTE NOTE provi
20. riginal product packaging in the event you need to ship the unit We suggest the package be insured against loss or in transit damage When sending your product include your name address phone number dated proof of purchase or copy and a statement about the nature of problem Warranty coverage is conditioned upon purchaser furnishing Alltrade with adequate written proof that they are the original purchaser and of the original purchase date Parts returned freight prepaid and insured to Alltrade s facility see above address will be inspected and at Alltrade s option repaired and or replaced free of charge if found to be defective and subject to warranty Alltrade retains the sole discretion to determine whether any item or part is nonconforming and if so whether the item and or part will be repaired and or replaced If the unit is repaired new or 16 reconditioned replacement parts may be used If Alltrade chooses to replace the product it may replace it with a new or reconditioned one of the same or comparable design The repaired or replaced unit will be warranted under the terms of the remainder of the warranty period Typically a defective product that is returned within the first 30 days after the purchase date will be replaced for items returned after the first 30 days and within the warranty period covered defective parts not subject to normal wear and tear or other exclusions will be repaired or replaced at Alltrade s option
21. se of the tool for COMMERCIAL PURPOSES OR ON A JOBSITE is not covered under this warranty The date of purchase shall be the date of shipment to the original purchaser or the date the original purchaser took possession custody or control of the product whichever occurred first This warranty shall be null and void if the product or any component thereof is modified altered or used for any commercial purpose or on a jobsite This warranty does not apply to any other product and or component thereof manufactured or distributed by Alltrade and does not apply to products and or components thereof designed manufactured and or assembled by others for which Alltrade makes no warranties whatsoever THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF Warranty Performance By purchasing the product purchaser expressly acknowledges and agrees that their sole and exclusive remedy under this warranty shall be strictly limited to the repair or replacement of any covered nonconforming items or parts thereof provided that any such nonconforming item and or part is promptly returned to Alltrade s facility postage pre paid and insured address ALLTRADE Warranty Claims amp Repair 1431 Via Plata Long Beach CA 90810 Attn Customer Service 1 800 590 3723 within the applicable warranty period with a written request by purchaser that Alltrade repair and or replace the nonconforming item and or part We recommend that you keep the o
22. table and may lead to loss of control Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use the tool if the power switch does not turn it ON or OFF A tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the power cord plug from the power source before making any adjustments changing accessories or storing the tool Such preventive safe ty measures reduce the risk of starting the tool accidentally Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users A CAUTION Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may create a risk of injury when used on another tool Tool service must be performed only by qualified repair personnel Service 0 maintenance by unqualified personnel may result in a risk of injury When servicing a tool
23. use only identical replacement parts Follow instructions in the Maintenance section of this manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury SPECIFIC SAFETY RULES AND OR SYMBOLS CAUTION Hold tool by insulated gripping surfaces when perform ing an operation where the cutting tool may contact hidden wiring or its own cord Contact with a live wire will also make exposed metal parts of the tool live and shock the operator SAFETY RULES FOR ANGLE GRINDERS A WARNING Never use this tool without the proper guard The grinding wheel could shatter during use Make sure the guard covers the side of the wheel facing you Never bounce the tool while grinding This may crack the wheel Grinding metal will cause sparks Keep them directed away from people and flammable materials Always keep the guard positioned so that as much of the exposed disc as possible is pointing away from you Keep children and pregnant women away from the work area until the grind ing is completed and the area has been cleaned up CAUTION Always wear full eye face and body protection Wire bristles may break off and fly toward the user Always wear ear protection when grinding in enclosed spaces Noise level may be amplified in such locations and may cause perma nent hearing loss Always wear an OSHA approved dusk mask or respirator when inside the
24. work area Replace the filter daily NOTE Not all dust masks offer protection from lead paint dust Be sure to use the proper mask for the job Before connecting the tool to the power supply follow the safety instructions for installing the grinding and cutting wheels Do not lock the wheels too tight or cracks may occur Use only grinding and cutting wheels with the correct bore size for the spindle of the grinder Use standard parts Do not use coolant or water and do not use as a fixed grinder Do not start the tool when grinding or cutting wheels are touching the work area Keep the power cord well away from the cutting area during use Always position the cord so that it will not be caught in the workpiece when the grinder is in use Always have the guards in place and properly positioned when using grind ing wheels or wire cup brushes Secure the material being grinded Never hold it in your hand or across your legs Do not use your legs or feet to stabilize the workpiece Unstable support can cause loss of control and could result in lacerations or injury Always make sure no one including the user is in line with the tool when starting the motor Always use both hands when operating the Angle Grinder Always hold this tool by the insulated gripping surfaces If this tool should accidentally cut across its own cord or hidden wiring all exposed metal parts will become live and could seriously shock the user When using th
Download Pdf Manuals
Related Search