Florida Pneumatic FP-1061A Use and Care Manual
Contents
1. at an air pressure of 90 pounds per square inch gauge pressure 90 PSIG maximum at the tool Use of higher air pressure can and may cause injury Also the use of higher air pressure places the internal components under loads and stresses they were not designed for causing premature failure The air supply should be clean and dry For best results drain the moisture from your compressor daily Description The Florida Pneumatic model FP 1061A 5 Straight Handle Needle Scaler is designed for use on metals for rust and corrosion removal as well as peening welded joints devices as furnished by the manufac turer Where an air tool is modified or altered the modifier shall provide the safeguards to enable it to be safely used in the operations intended and to comply with any applicable provisions as contained in ANSI B186 1 WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to cause cancer birth defects or reproductive harm Some examples of these chemicals are Tool Installation Pressure regulators shall be used to limit air pressure to the rated pressure where the supply pressure exceeds the tool s rated pressure Air hoses and lines shall be relieved of compressed air before Safety Instructions The following general instructions are furnished as general guidelines for use of your pneumatic tool They cannot comprehensively cove2. AX PLEASE READ AND FOLLOW ALL WARNINGS Read Operating Instructions Always become familiar with all the instructions and warnings before operating any power tool Always Wear Approved Eye Protection Impact resistant eye protection should meet or exceed the standards as set forth in the United States ANSI Z87 1 Occupational and Educational Eye and Face Protection Look for the marking Z87 1 on your eye protection to insure that it is an approved style For further information ANSI Z87 1 Occupational and Educational Eye and Face Protection is available from the American National Standards Institute Inc 11 West 42nd Street New York NY 10036 Hearing Protection is Recommended Hearing protection should be used when the noise level exposure equals or exceeds an 8 hour time weighted average sound level of 85 dBA Process noise reflective surfaces other tools being operated nearby all add to the noise level present in your work area If you are unable to determine your noise level exposure we recommend the use of hearing protection Avoid Prolonged Exposure to Vibration Tools can vibrate during use Movements can cause injury Stop using any tool if discomfort tingling feeling or pain occurs You should consult your physician before resuming use of the tool FP 1061A rFi gt RiDF PNEU M A T 1 CSTRAIGHT HANDLE NEEDLE SCALER 90 psig 90 PSIG Maximum This tool is designed to operate
3. ctive in material or workmanship within one year after purchase return it to any authorized service center or Florida Pneumatic freight prepaid Please enclose your name address and adequate proof of purchase and a short description of the Tool Operation and Maintenance eDaily before putting tool into operation disconnect air hose and pour 1 4 oz of air tool oil into the air inlet eBlow out air line to clear it of accumu lated dirt and moisture Connect tool and operate momentarily to allow oil to be carried through tool eHose runs longer than 8 feet should be connected to a 1 2 ID hose to provide sufficient volume for proper performance e We recommend oil made exclusively for air tools or equivalents which include moisture absorbants rust inhibitors metal wetting agents and an EP extreme pressure additive defect Florida Pneumatic will at their option repair or replace defective tools free of charge Repairs or replacements are warranted as described above for the remainder of the original warranty period Florida Pneumatic sole liability and your exclusive remedy under this warranty is limited to repair or replacement of the defective tool There are no other warranties expressed or implied and Florida Pneumatic shall not be liable for incidental consequential or special damages or any other damages costs or expense of repair or replacement as described above
4. or disjointed unless there is automatic valve closing protec tion at the joint being separated Syn thetic lubricants which can cause deterioration of elastomer seals shall not be used in air systems of air tools Tool Maintenance It shall be the tool owner s and or employer s responsibility to assure that tools are maintained in a safe operating condition Tool maintenance and repair shall be performed by authorized trained competent personnel Tools shall be disconnected from their compressed air supply before repairs are attempted Repairs shall be consistent with the manufacturer s recommended proce dures Tool hoses and fittings shall be replaced if unsuitable for safe operation It shall be the tool owner s and or employer s responsibility to keep required rating markings and warnings on the tool in legible condition Read these instructions carefully before attempting to install operate or service this Florida Pneumatic product Failure to comply with the instructions could result in personal injury and or property damage Retain these instructions for future reference FL RIDA ann C STRAIGHT HANDLE NEEDLE SCALER FL RIDA sine STRAIGHT HANDLE NEEDLE SCALER Specifications SSE as cenaninis eassaas eeonset E E aanansiacsameianudenatastvnng 5 700 BPM WAV ONCE ace tecseeeetierniacatacntenatereiccateretacqtareceratenntesatesagasatacatarationntanedueteanaceondenoteestenmaentesenscode
5. r all possible or conceivable uses of the subject tool Lead from lead based paints Crystalline silica from bricks cement and other masonry products Arsenic and chromium from chemi cally treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles A Division of Florida Pneumatic Manufacturing Corporation 851 Jupiter Park Lane Jupiter Florida 33458 561 744 9500 Fax 561 575 9134 Toll Free 1 800 327 9403 For additional information on the safe use of air tools we advise you to obtain a copy of ANSI B186 1 Safety Code for Portable Air Tools available from the following source American National Standards Institute Inc 11 West 42nd Street New York NY 10036 The use of the word shall in the following instructions indicates that adherence to the particular require ment is necessary to conform to ANSI B186 1 Tool Application and Usage Portable tools shall be used only for the purposes intended in their design and within the capacity for which they were intended and rated It shall be the tool owner s and or employer s responsibility to instruct each operator in the safe use of the tool Tools shall not be used without guards and safety being disconnected
6. s 3 1 4 Ibs Over ak Teno x cesses series saeese Serica aa a aes ose ees 12 1 2 Average air COMSUIMPTION qu ee ceeeeeee eee eee eee eeeeeeeeeeeeeeeeneeeeneeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeaaas 4 CFM Air WAST sasapieratte tos vous tond a a ENE R E O EEEE 1 4 NPT Recommended hose SIZE ccccccccccccceeeceeeeeceeeeeeeeeeeeeeeeceeeeeeeeeeeeeseuaaeaanananeaananaaaaaaaaananaaeas 3 8 I D Maximum air pressure 5 io lacccsitcencoten eteanatine den vedswndteanslsn de aAa aa aaaea a Aaa Eaa AAAA EON 60 PSI Parts Breakdown for FP 1061A Replacement Parts 1 Scaler housing 109100 11 Valve block stop 121030 2 Cap screw 109070 12 Lock nut 108150 3 Spring 109120 13 Spring 118020 4 Needle holder 109110 14 O ring 115120 5 Buffer 109040 15 Trigger valve stem 120230 6 Set of 18 needles 109130 16 O ring 2 115160 7 Anvil 109010 17 Trigger valve body 120120 8 Barrel complete 425675 18 Retaining pin 111220 inc 112040 1 amp 425570 1 19 Trigger valve lever 120330 9 Piston 112040 1 20 Retaining pin 111230 10 Valve block assy 425570 1 21 Handle 262375 22 Regulator 5711 Florida Pneumatic s Limited Warranty Florida Pneumatic warrants their tools to be free from defects in material and work manship for one year from the date of purchase This warranty does not apply to tools which have been abused misused modified or repaired by someone other than Florida Pneumatic or their authorized service centers If a Florida Pneumatic tool proves defe
Download Pdf Manuals
Related Search