SPEEDWAY 50959 Use and Care Manual
Contents
1. standards NAT warrants to the original retail consumer a 1 year limited warranty from the date the product was purchased at retail and each product is free from defects in materials Warranty does not apply to defects due directly or indirectly to misuse abuse negligence or accidents repairs or alterations or a lack of maintenance NAT shall in no event be liable for death injuries to persons or property or for incidental special or consequential damages arising from the use of our products To receive service under warranty the original manufacturer part must be retumed for examination by an authorized service center Shipping and handling charges may apply Ifa defect is found NAT wil either repair or replace the product at its discretion DO NOT RETURN TO STORE For Customer Service Email feedback natitools com or Call 1 800 348 5004 Teodbacktinatitols com 4 800 348 5004 g o Q a u 3 2a o o o E a z 3 E o For customer service ca 1 800 248 5004 or emat Paris List Call 1 800 348 5004 for assistance or replacement parts Please provide tho following information Address any correspondence o Model number Part description and number as shown in parts list DAR Aera on Ive Serial number if any Huntington 48750 No Description lary No Description si 1 Tank 1 30 Cylinder Cover 1 2 Up2. 04 5 Allow the compressor to build up air compressor DO NOT use the compressor unti itshuts off approx 4 minutes 6 After the compressor builds up enough pressure and shuts off adjust he regulator knob so that the air output is enough to properly power the tool Ensure the output will not exceed the tool s maximum air pressure Turning the knob clockwi will increase the pressure and turning it counterclockwise will decrease the pressure Aways gradually adjust the pressure while checking the output gauge 7 Close the in line shutoff valve between the compressor and the air hose 8 Make sure the air tool s switch is in the OFF position 9 Connect the air tool to the air hose 10 Open the in line shutoff valve 11 Use the tool as needed 12 After the job is completed tum the power switch OFF and Unplug the air compressor 13 Close the in line shutoff valve Bleed the air from the tool and disconnect it 14 Tum the drain valve at the bottom of the tank two turns to release any build up moisture and the intemal tank pressure Close the vahe after the moisture ahs drained out Do ot remove the drain valve 15 Clean and store the air compressor indoors Emergency Depressurization Iit is necessary to quickly depressurize the compressor turn the power switch OFF and NOTE Check for air leaks while the air compressor is pumping and after air pressure
3. 15 Do not direct the air stream atpeople or animals compressor plugged in while unattended 17 Drain the tank daily and after use Arusted tank causes failure and explosion 18 Do not remove the valve cover or adjust internal components 19 Do notuse the air hose to move the compressor 20 The compressor head gets hot during use Do not touch it during or immediately after use 21 Release the tank pressure before moving 22 Onlyuse accessories that are rated ata minimum working ASSEMBLY 1 Ensure the power switch is OFF and the unitis unplugged 2 Attach recoil hose to the regulator manifold using an open end wrench Fully open all regulators and valves 3 Plug in the power cord 4 Tum the power switch ON and press the reset button next to the switch 5 Allow the unit to run for 15 minutes Ar will fow freely through the air hose 6 Tum the power switch OFF 7 Unplug the power cord and remove the male coupler OPERATION Note Allow adequate time when filing tres Large tires mayrequire more time This productis designed for inflation stapling brad nailing and air brushing 1 Tur the red regulator knob completely counterclockwise 2 Close the drain valve 3 Plug the power cord into a grounded 120V electrical outlet 4 Tum the power switch ON been repaired pressure of 150 PSI Press the reset bution nex to the switch TeodbackGnatitools com 4 800 348 50
4. 9 10 11 3 Do not modify the outlet plug in anyway 4 Do notuse adapter plugs with grounded compressors 5 Do not expose the compressor to rain or wet conditions twill increase the risk of electrical shock 6 Do notabuse the cord Keep it away from heat oll sharp edges or moving parts Ithe cord is damaged in any way do notuse 7 Stay alert while operating the compressor Do not use while tred or under the Influence of drugs alcohol or medication 8 Wear proper protective gear Such as gloves boots and ANSI approved eye protection 9 Ensure the compressor is shutoff before connecting itto the power source making any adjustments changing accessories storing or moving the compressor 10 Do notuse the compressor ifthe switch does not turn on and off 11 Check the compressor for damages misalignments breakages or conditions that may affect the compressor during operation If problems are present do not use the compressor until they have 12 Do notuse the compressor for jobs itwas not intended or overload the compressor 13 Do not spray flammable liquid in a confined area or towards a hot surface The spraying area must be well ventillated Do not smoke while spraying or spray near flames or flammable materials Keep the compressor at least 20 feet away trom explosive vapors 14 Do not adjust the regulator higher than the marked maximum pressure
5. Please carefully read and save these instructions before attempting to assemble maintain install or operate this product Observe all safety information to protect yourself and others Failure to observe the instructions may result in property damage and or personal injury Please keep instructions for future reference Important Operating Instruction 3 GALLON PANCAKE COMPRESSOR CALIFORNIA PROPOSITION 65 WARNING You can create dust when you cut sand drill or grind materials such as wood paint metal concrete cement or other masonry This dust often contains chemicals known to cause cancer birth defects or other reproductive harm Wear protective gear WARNING This product or its power cord may contain chemicals including lead known to the State of California to cause cancer and birth defects or other reproductive harm Wash hands after handling Important When using equipment a few safety precautions must be observed to avoid Injuries and damage Please read the complete operating manual with due care Keep this manual in a safe place so that the information is available at all times Ifyou give the equipment to anyother person give them these operating instructions as well We accept no liability for damage or accidents which arise due to non observance of these instructions and the safety Information herein Breathable Air Warning This compressor pump is not equipped and should no
6. cut out by applying soapy water to the connections Do not use the compressor unless all the connections are air tight Extra air leaking out will cause the compressor to operate too often and will increase wear on the compressor NOTE As long as the power Switch is ON the compressor s operation is automatic and controlled by an internal pressure switch The compressor will tum on automatically when the air pressure drops to 85 PSI and will tum off automatically when the air pressure reaches 100 PSI DO NOT MODIFY THE AR PRESSURE SETTINGS OF THE INTERNAL PRESSURE SWITCH Changing the automatic pressure levels may cause excess pressure to accumulate and will cause a hazardous situation and void the warranty Automatic Shut Off System Ifthe compressor automatically shuts oft 1 Shutoff all tools 2 Allow the compressor to cool down approx 10 minutes 3 Press the reset button to start the operation 4 Resume operation Possible repeated automatic shut off causes are using an extension cord that is too long or narrow or an air leak or open hose is causing the compressor to cycle too often and build up heat Correct any issues before continuing to use the compressor MAINTENANCE Before each us Inspect the compressor for loose hardware binding of or misalignment of moving parts cracked for broken parts damaged electrical wiring and anyother condition that may affect ts operation If
7. per Cover 1 31 O Ring 3 3 Bottom Cover 1 32 Circuit Board 4 Copper Tube 1 33 Muffer 1 5 Switch 1 34 Fan 1 6 Safety Valve 1 35 M5x10 Screw 1 7 Handie 1 36 M4x8 Screw 2 8 Foot 3 37 M3x6 Screw 4 9 Pressure Output Gauge 1 38 M6x10 Screw 1 10 Damping Pad 4 39 washer 1 11 Drain Valve Assembly 1 40 M2x40 Screw 4 12 Connecting Tube 1 41 Power Cord cf 13 Nut 1 42 Cord Holder c 24 Pressure Switch 1 43 Tank Pressure Gauge 1 15 Connector 2 44 Screw L4 16 Nut 1 45 Lock Washer 17 Regulator 1 46 M6x15 Screw 6 18 Motor Assembly 1 47 Screw 1 19 608 22 Bearing 3 48 M5x25 Screw 2 20 Crank 1 49 Washer 2 21 Piston 1 S0 Reset Button 1 22 Air Input Valve 1 51 Overload Protector Nut 1 23 Copper Plane Keeper 2 52 Electric Wire 1 24 O Ring 1 53 Terminal Sheath 2 25 Piston Ring 1 54 Terminal 2 26 Cylinder 1 55 Spring 1 27 Outlet Valve Cover 1 56 Ball 1 28 Outlet Valve 1 57 O Ring 1 29 O Ring 1 58 Screw 4 Teedbacknatitools com 4 800 348 5004
8. t be used as is to supply breathing quality air For any application of air for human consumption the air compressor pump will need to be fitted with suitable in line safety and alarm equipment This additional equipment is necessary to property filter and purity the air to meet minimal specifications for Grade D breathing as described in Compressed Gas Association Commodity Specification G 7 1 1966 OSHA 29 CFR 1910 134 andlor Canadian Standards Associations CSA CAUTION FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL COMPLETELY AND CAREFULLY BEFORE OPERATING Failure to follow all instructions as listed below may result in electrical shock fire andor serious personal injury SPECIFICATIONS Air Outlet 1 4 inch NPT Air Pressure Auto shutoff 100 PSI Restart 85 PSI Air Tank Capacity 3 gallons Air Flow Capacity 0 6 SCFM 90 PSI 1 SCFM 40 PSI Single Stage Pump Feature Overheat auto shutdown and restart SAFETY INSTRUCTIONS 1 Keep your work area clean and well lit 2 Do not operate the compressor in explosive atmospheres such as in the presence of flammable liquids gases or dust The sparks produced by the compressor mayignite flammable dust or fumes For warranty purchases plea keep your dated proof of purchase le or attach to the manual for safekeeping For customer service cat 1 800 248 5004 crema feedback natitools com d 8805095
9. the power cord is damaged it must be replaced bya qualified technician After use Wipe the external surfaces with a dean cloth TesdbsckGnatitools com 3 4 800 348 5004 MAINTENANCE SCHEDULE Note The frequency of use and environment in which itis used will affect how often you need to check the components and perform maintenance Daly 1 Make sure the nuts and bolts are tight 2 Drain moisture from the air tank 3 Check for abnormal noise or vibration 4 Check for air leaks by applying soapy water to joints while the air compressor is pressurized Look for air bubbles 5 Wipe off any oil or dirt from the compressor by using a damp cloth with a mild detergent or solvent Monthly Inspect safety valve Draining the Moisture from the Tank The drain tank is located under the tank It must be accessed dailyto release all trapped air and moisture from the tank This will eliminate condensation which can cause internal tank corrosion To empty the air and condensation 1 Switch the compressor OFF 2 Place a collection pan under the drain tank 3 Unthread the drain valve two or three tums ONLY 4 When all the pressure and moisture is released close the valve Tesdbsck natitools com 4 800 348 5004 Limited Manufacturer Warranty North American Too NAT Industries makes every effort to ensure that this product meets high quality and durability
Download Pdf Manuals
Related Search