SPEEDWAY 50959 Instructions / Assembly
Contents
1. Please careflly read and save these instructions before attempting to assemble maintain install or operat this product Observe all safety information to protect yourself and others Fallur to observe the instructions may result in property damage and or personal injury Please keep instructions for future reference Q Important Operating Instruction Terasnvanee T 3 GALLON PANCAKE COMPRESSOR Model 50959 CALIFORNIA PROPOSITION 65 accidents which arise due to CAREFULLY BEFORE WARNING You can create dust non observance of these OPERATING Failure to when you cut sand drill or grind _ instructions and the safety follow all instructions as information herein listed below may result in electrical shock fire andlor serious personal injury materials such as wood paint metal concrete cement or other masonry This dust often Breathable Air Warning contains chomicals known to cancer birth defects or This compressoripump is not SPECIFICATIONS other reproductive harm Wear equipped and should notbe Air Outlet 1 4 inch 4 NPT protective gear paad ee esa Air Pressure Auto shutoff reathing quality air For any 100 PSI Restart 85 PSI WARNING This product orits application of air forhuman An Tank Capaci a yeiens pamar cord may contain consumption tho air Air Flow Capacity 08 chemicals including lead compressoripump will nee SCFM 90 PSI 1 SCFM known to the State of California to be fi2. 2 Allow the compressor to cool down approx 10 minutes 3 Press the reset button to start the operation 4 Resume operation teedoackepnatools com 18003485004 Possible repeated automatic shut off causes are using an extension cord that is too long or narrow or an air leak or open hose is causing the compressor to cycle t00 often and build up heat Corect any issues before Continuing to use the compressor teodackepattools com 18003485004
3. 5 minutes Air will low freely through the air hose 6 Tum the power switch OFF 7 Unplug the power cord and remove the male coupler OPERATION Note Allow adequate time when filing tires Large tires may require more time This product is designed for inflation stapling brad nailing and air brushing 1 Tum the red regulator knob completely counterclockwise 2 Close the drain valve 3 Plug the power cord into a grounded 120V electrical outlet 4 Tum the power switch ON Press the reset button next to the switch 5 Allow the compressor to build up air compressor DO NOT use the compressor until it shuts off approx 4 minutes 6 After the compressor builds up enough pressure and shuts off adjust he regulator knob so that the air output is enough to properly power the tool Ensure the output will not exceed the tool s maximum air pressure Turning the knob clockwise will increase the pressure and turning it counterclockwise will decrease the pressure Always gradually adjust the pressure while checking the output gauge 7 Close the in line shutoff valve between the compressor and the air hose 8 Make sure the air tool s switch is in the OFF position 9 Connect the air too to the air hose 10 Open the in line shutoff valve 11 Use the tool as needed 12 After the job is completed tum the power switch OFF and unplug the air compressor 13 Close the in line shut of
4. f valve Bleed the air from the tool and disconnect it 14 Tum the drain valve at the bottom of the tank two turns to release any build up moisture and the internal tank pressure Close the valve after the moisture ahs drained out Do not remove the drain valve 15 Clean and store the air compressor indoors Emergency Depressurization If it is necessary to quickly depressurize the compressor turn the power switch OFF and then pull on the safety valve ring to quickly release stored air pressure NOTE Check for air leaks while the air compressor is pumping and after air pressure cut out by applying soapy water to the connections Do not use the compressor unless all the connections are air tight Extra air leaking out will cause the compressor to operate too ofen and will increase wear on the compressor NOTE As long as the power switch is ON the compressor s operation is automatic and controlled by an internal pressure switch The compressor will tum on automatically when the air pressure drops to 85 PSI and will turn off automatically when the air pressure reaches 100 PSI DO NOT MODIFY THE AIR PRESSURE SETTINGS OF THE INTERNAL PRESSURE SWITCH Changing the automatic pressure levels may cause excess pressure to accumulate and will cause a hazardous situation and void the warranty Automatic Shut Off System If the compressor automatically shuts off 41 Shut off all tools
5. tted with suitable in 30 pa w to cause cancer and birth line safety and alarm Single Stage Pump Feature defects or other reproductive equipment This additional EANA ots CAA harm Wash hands after equipment is necessary to and restart handling properly filter and purify the air to meet minimal ASSEMBLY specifications for Grade D breathing as described in When using equipment a few Compressed Gas Association 1 Ensure the power switch is eavodtnaveatigume ond Commonty Specenion a OTE ore faunas damage Please read the complete Taya 199e OSHA 20 CFR operating manual with due care 1010 134 andor Canadian Standards Associations Important 2 Attach recoil hose to the Keep this manual in a safe place regulator manifold using an so al he information is avalabie esa open end wrench Fully open at all imes if you give the CAUTION all regulators and valves equipment to any other person give them these operating 3 Plug in the power cord instructions as well We accept no FOR YOUR OWN SAFETY liability for damage or READ INSTRUCTION MANUAL COMPLETELY AND For warranty purchas please keep your daled proof of purchase File or altach to the manual for safe ping For customer service cal 800 349 5004 or email teadbackiBnaitools com A 88050959 10711 4 Tum the power switch ON and press the reset button next to the switch 5 Allow the unit to run for 1
Download Pdf Manuals
Related Search