Waekon 20560 Use and Care Manual
Contents
1. Passive Sensor test the red LED lights when the sensor resistance is too low or a short circuit 3 MODE Corresponding green LED lights to indicate the tester s current mode 4 SIGNAL ERROR Red LED lights or flashes when an inconsistent signal is detected Note A sudden start or stop of the wheel under test may cause this light to flash This is normal and does not indicate an error with sensor or tone wheel 5 PWR Green LED lights when the tester is powered on LED will flash and the tester will turn off if the battery is too low to operate the tester 6 POWER MODE Button Press and hold to turn the tester OF ON Press and release to change to the next mode 7 ROTATION The green LEDs flash chase when the rotating to indicate a good signal from the wheel s eel is ensor Before You Begin e Usea lift or jack to raise the vehicle so freely spun by hand el can be Note An incorrect hookup will not tester Test Procedures The test procedure involve 1 Run a sensor test adtiv to determine if the s 2 Using a scan tool ver al the sensor Note If you d proceed to step 3 ave a scan tool ns 3 Perform the pinpoint test to locate an in Step 1 Run a Sensor Test Hookup Diagrams Note An incorrect hookup will not damage the vehicle or the tester Passive Sensor Test Procedure 1 Connect the tester to the vehicle s ABS sensor see Hookup Diagrams2. Sensor Testing N th If th le 2 Turn the tester ON and then press and release the Mode button until the Passive LED is lit t the tester as sk in Diagram 2 okup shown in Diagram 1 does not work reverse the OPEN LED is lit Recheck the connection from the sensor to t CONTOL flex probe If the OPEN LED remains lit the sensor is de UNIT e E A SHORT LED is lit The sensor has an internal short and is defective Check for a short to the chassis ground by connecting the black lead from the tester to the vehicle chassis ground If the SHORT LED remai connected to the chassis ground then th ground and may not function properly e aaa SENSOR ken BLACK 3 Spin the vehicle s wheel by hand at a ROTATION LEDs will flash in sequen speed sensor signal SIGNAL ERROR LED i ed tone ring CONTOL UNIT B EN A SIGNAL ERROR LED fl ormal when the wheel is started and stopped H i Diagram 2 spinning of the w ere SENSOR i FLEX PROBES l p ctiv Sensor Test al i if GREEN r hicle s ABS sensor s 5 E E l CAR CHASSIS PLACK ton Pinpoint Testing or using Diagram 4 SIGNAL ERROR LED or
3. To Replace the Battery The tester uses a standard 9 volt battery If the battery is too low to operate the tester the PWR LED will flash and then the tester will automatically turn off The battery can easily be accessed by removing the plug located on the back of the tester Customer Care amp Tech Support 800 342 5080 Don t forget to check out other testers equipment and parts at our websites Access our Quick n E Z Parts and Service from any of these sites 24 7 for ordering parts or service www hickok inc com www waekon com www quick n ezparts com OV Warrant re recone ABS tron TESTER ubject to the conditions that follow and are noted below this product is warranted to be free from defects in material and workmanship under proper use and in accordance with the manufacturer s written recommendation and specifications for a period designated below on all products Instructions e This product carries a one year limited warranty The manufacturer s obligation under this warranty is limi to unaltered products returned to the manufacturer by th initial end user of the new products Therefore this warranty does not cover any products resold by the end user to third parties nor any reconditioned products sold as suck by the 2 Terminal Round 2 Terminal Spade Small Male Small Male 2 Terminal Round Extra Large Male the manufacturer This warranty does not cover par
4. mal when the wheel is started and st Note If the hookup shown in Diagram 3 does not work try testing without the ground reversing the leads with amp without the ground if it flashes during consistent e error with the tone ring CONTOL Diagram 3 o the vehicle s harness and spin the EN aaa FEREROOES g a scan tool to read the wheel speed and f f Br U OOO ot you have a signal If no signal is present ARNES 7 if I i form a Pinpoint Test aiii CT Disconnect the ABS sensor and connect the tester directly to e harness using the flex probes see Hookup Diagrams Turn the tester ON 2 3 Press and release the MODE button until the SIMULATION LED is lit CONTOL SS i f i ff A Bc 4 Set the vehicle to KOEO key on engine off Diagram 4 A 5 Using your scan tool determine that a speed reading is obtained from the appropriate wheel speed sensor data aovo sensor ony FLEX PROBES x p GREEN The reading will be in a range from 10 MPH to 15 MPH venice B o rA depending on the vehicle s make and model p ONES EO O O GREEN A
5. ts such as batteries nor does it coves i product during shipping In the event it is deter tampered with or altere all claims against the produ claims must be submi 2 Terminal Round 2 Terminal Round 2 Terminal Alligator Small Female Medium Female edures These procedures purchase must be e the seller or by point anufacturer will make e 2 Terminal Spade Small Female Main control unit outside of the warrant make such judgmen will be notified that wari ion will be necessary to e manufacturer deems ill then be shipped back to the Interface Cable i V4 The ABS Sensor Pinpoint Tester and Flex Probe adapters quickly and easily isolate the sensor from the vehicle harness and control module The tester checks both active and passive sensors for proper voltage frequency output and reluctor wheel tone ring integrity The tester will also check the passive sensor or any special indirect incidental or consequential for opens and shorts ages costs or losses wasn ETC 10514 Dupont Ave 19121 016 Cleveland OH 44108 2011 Hickok Inc All rights reserved About the Control Panel C OPEN ACTIVE SHORT PASSIVET SIMULATION SIGNAL ERROR Q PWR Q ROTATION 00 04 1 OPEN During the Passive Sensor test the red LED lights when the sensor resistance is too high or an open circuit 2 SHORT During the
Download Pdf Manuals
Related Search