General International 10-050 M1 Use and Care Manual
Contents
1. PORT PORTABLE DUST COLLECTOR 10 050 UNPAGKING AND CHECKING GONTENTS UNPACK AND REMOVE ALL COMPONENTS OF YOUR MACHINE FROM THE BOX AND COMPARE WITH THE PARTS LISTED BELOW REPORT DAMAGED OR MISSING ITEMS TO YOUR DEALER DISTRIBUTOR IMMEDIATELY DUST COLLECTOR W BASE amp HANDLE COLLECTION FILTER BAG DUST HOOD UPPER SUPPORT ARM SCREW LOCK KNOB DUST HOSE FASTENING BRACKET DUST HOOD DUST HOOD LOWER SUPPORT ARM U BRACKET LONG CARRIAGE BOLT LOCK KNOB 3 FLANGE BOLT 2 HOSE CLAMP 2 FLAT WASHER BAG CLAMP KEY WRENCH CASTER 4 ADHESIVE FOAM GASKET SHORT CARRIAGE BOLT SPROCKET WASHER 2 ASSEMBLY STEP 1 INSTALLING THE CASTERS ON THE BASE FRAME Lay the dust collector on its side as shown and using the supplied wrench install the 4 casters to the underside of the base frame Tighten the caster bolts into the corresponding holes in the base frame until snug STEP 2 MOUNTING THE LOWER SUPPORT ARM Using the 2 supplied flange bolts loosely attach the fastening bracket to the dust collector Fit the lower support arm into the opening between the dust collector and the mounting bracket as shown For a secure stable fit slide the end of the support arm down through the opening so that protrudes roughly 1 2 below the bottom of the mounting bracket Then tighten the flange bolts to clamp the s2. ET DUST HOOD LOWER SUPPORT INNER TUBE CARRIAGE BOLT M8 x 40mm WASHER 5 16 x 23mm SCREW LOCK KNOB 5 16 x 3 4 INSIDE TUBE CAP PHILLIPS HEAD SCREW M3 x 6mm OUTSIDE TUBE CAP DUST HOOD LOWER SUPPORT OUTER TUBE PHILLIPS HEAD SCREW M3 x 5mm FLANGE BOLT 5 16 x 1 2 WASHER 1 4 x 25mm UL SWITCH POWER CORD 16A x 3C x OF MOTOR PACKING NUT 5 16 SPROCKET WASHER M8 QTY oll GENERAL UNTERNATIG 8360 Champ d Eau Montreal Quebec Canada HIP 1Y3 Tel 514 326 1161 Fax 514 326 5565 Parts amp Service Fax 514 326 5555 Order Desk orderdesk general ca www general ca IMPORTANT When ordering replacement parts always give the model number serial number of the machine and part number Also a brief description of each item and quantity desired
3. S Do not pull or carry the machine by any part other than it s handle Sound Level The sound level of this machine is rated at approximately 85 dB during operation Make sure that adequate hearing protection is used and that the overall sound level within the working environment is taken into consideration 11 12 Do not handle the electric plug with wet hands Do not vacuum anything that is burning smoking or smoldering such as cigarettes matches or hot ashes 13 To avoid potential health hazards from vapors or dusts do not vacuum toxic material 14 15 16 17 18 19 20 Do not use this unit outdoors or on or near wet surfaces Make sure the unit is properly grounded If tool is e quipped with three prong plug it should be plugged into a three pole receptacle Never remove the third prong Always disconnect tool from power before servicing performing any maintenance or repairs and when changing bags or hoses or if the machine will be left unattended Do not put any foreign objects into the ventilation inlet or outlet openings Make sure the switch is in OFF position before plug ging in cord Never stand on machinery Serious injury could result if the unit is tipped over The use of parts and accessories NOT recommended by General International may result in equipment mal function or risk injury DO NOT OPERATE THIS UNIT UNTIL THE PVC HOSE IS INSTALLED ONTO THE DUST INLET
4. SETUP amp OPERATION MANUAL FEATURES 8 SPECIFICATIONS Dust hood rotates 360 Support arm extends up to 12 Wide dust hood captures chips dust and debris Powerful 1 HP motor features sealed bear ings and shaft for quiet long lasting oper ation Comfort grip carrying handle for easy portability to place the unit where you need it Flexible 4 x 6 1 8 m collection hose included Adjustable multi position steel support arm to accommodate a variety of different machines or applications INLET DIAMETER 4 102 mm AIRFLOW CAPACITY 700 CFM HOSE LENGTH 4 102 mm X 6 1 8 m DUST HOOD 10 254 mm x 4 102 mm SOUND RATING 78 OB STATIC PRESSURE 4 3 INCHES OF WATER BAG CAPACITY 15 GAL 655 L OVERALL DIMENSIONS L x W x H 44 5X 18 7g X 43 4 1130 x 480 x 1100 mm MOTOR 1 HP 110 V 7 A WEIGHT Oley WES 23 5 KO FILTRATION CAPACITY 30 MICRONS Ol 10 OS ee zm za SES AEN M J REVISION 3 JUN 22 06 SEST SR GAY 4 SAX GENERAL lt INTERNATI NAL W LIC EUX yy WIAA TAT Y la N WSs a __ lt GENERAL INTERNATIONAL 8360 Champ d Eau Montreal Quebec Canada HIP 1Y3 Telephone 514 326 1161 Fax 514 326 5555 www general ca THAN K YOU for choosing this General International model 10 050 Dust collector This dust collector has been carefully t
5. ate All electrical connections should have proper contact Running on low voltage will damage the motor AN To avoid risk of shock or fire do not operate with a damaged power cord or plug Replace damaged cord or plug immediately ADJUSTMENTS AND CONTROLS POWER ON OFF Make sure the switch is in the OFF position before plugging the power cord into a matching outlet POWER ON POWER OFF SAFETY KEY PREVENTS START UP WHEN REMOVED A c OCU OCU 34 PART NO 10050 01 10050 02 10050 03 10050 04 10050 05 10050 06 10050 07 10050 08 10050 09 10050 10 10050 1 1 10050 12 10050 13 10050 14 10050 15 10050 16 10050 1 7 10050 18 10050 19 10050 20 10050 21 10050 22 10050 23 10050 24 10050 25 10050 26 10050 27 10050 28 10050 29 10050 30 10050 31 10050 32 10050 33 10050 34 10050 35 10050 36 10050 37 10050 38 10050 39 10050 40 10050 41 10050 42 10050 43 PARTS LIST 10 050 DESCRIPTION SPECIFICATION TUBE CAP ig SPONGE TUBE COVER x9 BASE HANDLE FLAT HEAD PHILLIPS SCREW 1 4 x 1 MOTOR SET SCREW 3 8 COLLECTOR BODY BAG CLAMP ch COLLECTION FILTER BAG BASE CASTER TUBE CAP 3 4 FLANGE BOLT 1 4 x 1 2 IMPELLER 9 SPECIAL WASHER HEX SOCKET SCREW M x 20 INLET COVER 4 PHILLIPS HEAD SCREW M5 x 10 HOSE CLAMP 4 HOSE 4 x 2M DUST HOOD L TYPE BRACKET LOCK KNOB DUST HOOD UPPER SUPPORT ARM CARRIAGE BOLT M8 x 16 KEY 5X5X25 FASTENING BRACK
6. ested and inspected before shipment and if properly used and maintained will provide you with years of reliable service To ensure optimum per formance and trouble free operation and to get the most from your investment please take the time to read this manual before assembling installing and operating the unit The manual s purpose is to familiarize you with the safe operation basic function and features of this dust collector as well as the set up maintenance and identification of its parts and com ponenis This manual is not intended as a substitute for formal woodworking instruction nor to Offer the user instruction in the craft of woodworking If you are not sure about the safety of performing a certain operation or procedure do not proceed until you can confirm from knowledgeable and qualified sources that it is safe to do so Once you ve read through these instructions keep this manual handy for future reference GENERAL INTERNATIONAL WARRANTY All component parts of General International machinery are carefully tested and inspected during all stages of production and each machine is thoroughly inspected upon completion of assembly Because of our commit ment to quality and customer satisfaction Generale International agrees to repair or replace within a period of 24 months from date of purchase any genuine part or parts which upon examination prove to be defective in work manship or material In order to obtain this
7. ternational disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment 10 Do not operate machinery when tired distracted or under the effects of drugs alcohol or any medication that impairs reflexes or alertness Do not operate this unit until a hose is installed onto the dust inlet The working area should be well lit clean and free of debris Keep children and visitors at a safe distance do not permit them to operate the unit Childproof and tamper proof your shop and all ma chinery with locks master electrical switches and switch keys to prevent unauthorized or unsupervised use Stay Alert Give our work your undivided attention Even a momentary distraction can lead to serious injury Fine particulate saw dust is a carcinogen that can be hazardous to health Work in a well ventilated area and wear eye ear and respiratory protection devices Do not wear loose clothing gloves bracelets neck laces or ornaments while operating machinery Do not vacuum or use this Dust Collector near flam mable or combustible liquids gases gasoline or other fuels lighter fluid cleaners oil or solvent based paints natural gas hydrogen explosive dust grain dust ma gnesium dust or gun powder Never leave the machine running with the power when not in operation IMPORTANT NOTICE HANDLING THE MACHINE The total weight of the machine is 52 LB
8. tlet peal off the backing of the adhesive foam gasket and stick the gasket onto the dust collector outlet cutting it to length if needed Fit the bag over the outlet and secure the bag onto the outlet using the supplied bag clamp Positioning and tightening the clamp on the gasket will ensure an airtight seal YOUR DUST COLLECTOR IS NOW READY TO BE PUT INTO SERVICE CONNECTING TO A POWER SOURCE Plug the dust collector into a proper receptacle Your power tools should be con nected to a dedicated electrical circuit of not less than 14 wire and should be protected with a 15 amp time lag fuse If an extension cord is needed use only 3 wire cords with 3 prong grounded type plugs and 3 pole receptacles Grounding This tool must be grounded to protect the operator from electrical shock The supplied motor recommended for your dust collector is wired for 110 Volt single phase and has a 3 conductor cord and 3 prong grounded plug to fit a grounded type receptacle W Do not remove the 3rd prong grounding pin from the plug to make it fit into an old 2 hole wall socket If an adapter plug is used W it must be attached to the metal screw of the receptacle Note Use of an adaptor plug is illegal in some areas Check your local codes Before connecting the motor to the power line make sure that the switch is in the OFF position and that the AN electrical current is of the same type as that stamped on the motor namepl
9. upport arm securely against the dust collector Attach the screw lock knob to the support arm as shown This knob is used to secure the arm at the desired STEP 3 INSTALLING THE DUST HOOD UPPER SUPPORT ARM Using the long carriage bolt flat washer and one lock knob attach the dust hood upper sup port arm to the lower arm as shown The lock knob is used to secure the upper arm in the desired position or angle STEP 4 MOUNTING THE DUST HOOD Using the short carriage bolt 6 and one lock knob attach the L bracket and sprocket washer G to the end of the upper support arm The lock knob is used to secure the dust hood once installed on the L bracket at the desired angle Using the remaining lock knob fit the dust hood onto the L bracket and sprocket washer The lock knob is used to secure the dust hood to the desired pivot position i i a ij j STEP 5 ATTACHING THE DUST HOSE 8 COLLECTION FILTER BAG Install a hose clamp on each end of the dust hose Slip one end of the hose onto the dust hood and using a Phillips head screw driver not supplied tighten the hose clamp uniil it is secure on the dust hood Slip the Opposite end of the dust hose onto the dust collector inlet and tighten the clamp until it is securely in place To create an airtight seal between the dust bag and the air ou
10. warranty all defective parts must be returned freight pre paid to General International Mfg Co Ltd Repairs attempted without our written authorization will void this warranty Disclaimer The information and specifications in this manual pertain to the unit as it was supplied from the factory at the time of printing Because we are committed to making constant improvements General International reserves the right to make changes to components parts or features of this unit as deemed necessary without prior notice and without obligation to install any such changes on previously delivered units Reasonable care is taken at the factory to ensure that the specifi cations and information in this manual corresponds with that of the unit with which it was supplied However special orders and after factory modifications may render some or all information in this manual inapplicable to your machine Further as several generations of this model of dust collector and several versions of this manual may be in circulation if you own an earlier or later version of this unit this manual may not depict your machine exactly If you have any doubts or ques tions contact your retailer or our support line with the model and serial number of your unit for clarification Rules for Safe Operation To help ensure safe operation please take a moment to learn the machine s applications and limita tions as well as potential hazards General In
Download Pdf Manuals
Related Search