Du Ha 70200 Use and Care Manual
Contents
1. Clamp assemblies to truck box bed rail in the following spacings measurements are to the center of the slot in the Bracket Clamp 51 75 for Standard Spacing 47 75 with one Offset Plate 43 75 with two Offset Plates Finger tighten the connections Level bracket assembly by adjusting each Rubber foot to contact the side of the truck box Center the brackets over the wheel well or move to any desired position as long as you can clamp on the bed rail STEP 4 Attach Humpstor to Brackets Humpstor Positions The Humpstor can be mounted with the lid opening toward inside the of the truck bed a or with the lid opening toward the outside of the truck bed b The assembly steps and hardware are the same other than the orientation of the Humpstor Page 3 Continued Humpstor Attachment Place the Humpstor A onto the Left E and Right F Brackets Thread one Hex Bolt 1 4 x 5 8 R Lock Washer 1 4 T and Flat Washer 1 4 S through bottom slots into the threaded holes in the bottom of the Humpstor Humpstor Adjustment Slide Humpstor in or out to desired position For example in a roll up cover the Humpstor should be slide away from the side rail of the truck bed to allow the lid to open for open bed the Humpstor should be as close as possible to the bed rail of the truck To adjust the Humptor vertically loosen the Clamp Bracket hex bolt Slide the Brackets up down as needed along the slot in2. of the Bracket Clamp pair can sandwich the truck bed rail T Offset Plate may be needed to not d P interfere with the topper mounting EXF Ph areas DU HA Inc website www du ha com phone 1 866 306 DUHA 3842 fax 1 218 998 4013 306 Saint Andrews Street South Fergus Falls MN 56537 Page 2 Continued Option Il Roll up Fold up or Hard Cover Attach Drop Down Plate H to Left E Right F Bracket with two Hex Bolts 5 16 x 5 8 Q two Flat Washers 5 16 V and two Lock Nuts 5 16 W Attach the Bracket Clamps to the Drop Down Plate the same as in Standard Mount Option IIl GM Short Box or other Short Box In the case of some truck beds or due to an obstruction the standard 51 75 spacing will not work In such cases use one or both Offset Plates to move the Clamp Assembly to a suitable location Attach Offset Plate I to Left E and or Right F Bracket with two Hex Bolts 5 16 x 5 8 Q two Flat Washers 5 16 V and two Lock Nuts 5 16 W Attach the Bracket Clamps to the Offset Plate the same as in Standard Mount Note Offset Plates should extend toward the middle of the Humpster Option IV GM Short Box with Bed Cover In some cases both Offset and Drop Down Plates are required Connect Offset plate holes to Left or Right Bracket slots and connect Drop Down Plate holes to Offset Plate slot F opposite STEP 3 Mount Brackets on Truck Attach Left and Right Bracket
3. the Brackets or Drop Down Plates Make sure Humpster is level then tighten all hardware connections ADJUSTMENT Note Humpstor should be adjusted as high and as close to the rail as possible while still allowing the lid to open properly ADJUSTMENT 7 STEP 5 Install Organizer Gun Holders Foam Organizer Gun Holders Stiffeners Sandwich each Foam Organizer Gun Holder C in between two Plastic Stiffeners D Place each Foam Organizer Gun Holder Stiffener assembly into the channel slots in the side walls of the Humpstor A facing opposing directions Note You may have to flex the assembly to get it into place Hint Stock of gun should rest in large groove barrel should rest in small groove Velcro Straps To secure guns in the Humpstor loop each Velcro Strap L through the holes in the top of the Foam Organizer Gun Rack C Stiffener D assembly Wrap the Velcro Strap around the gun then attach the Velcro Strap to itself and make sure it is securely fastened p Note Proper use of Velcro Straps help prevent guns from ZE mee a ee na bouncing on rough terrain Safety Instructions L S EA Center Brace Warning 75 LBS CAPACITY DO NOT EXCEED 75 POUNDS OF To maximize strength and stability use the Center Brace J CARGO IN THE HUMPSTOR CAUTION Do not store explosives or hazardous materials in the HUMPSTOR Do not place loaded guns in the HUMPSTOR For further instructions refer t
4. Installation Instructions DU HA HUMPSTOR DU HA Humpstor Tools Needed Hex Key Wrench supplied Wrench or Socket 3 8 2 Open End Wrenches 1 2 Wrench or Socket 7 16 Socket 1 2 Installation Instructions STEP 1 Attach Handle Place Handle B over holes in Lid Top Insert two Bolts 10 x 1 5 M through Handle B and Humpstor A Lid Secure with Flat Washer 10 N and Lock Nut 10 0 STEP 2 Assemble Bracket Install Stabilizer Foot Attach one Stabilizer Foot to the Left E and Right F Bracket by threading one Flange Nut 5 16 P onto Stabilizer Foot K shaft and insert through the lower hole of each Bracket E F Thread a second Flange Nut P onto Stabilizer Foot shaft sandwiching the Bracket in between Hint flanged side of nuts should face Bracket Note finger tighten Extended Stabilizer Foot Some installations require a longer Stabilizer foot Toyota Tundra for example In such cases prior to installing the stabilizer foot attach one Hex bolt 5 16 x 2 U and Coupling Nut 5 16 X to each Stabilizer Foot K e Attach Plates to Brackets Option Topper or Open Bed Mount Position two Bracket Clamps G facing each other allowing one to overlap the other Insert a Hex Bolt 5 16 x 2 U with Flat Washer 5 16 V through the Left E Right F Bracket and Bracket Clamp pair Thread loosely a Flange Nut 5 16 P onto the Carriage Bolt so the jaws
5. o the vehicle owners manual or contact DU HA Inc Insert each end in to a hole on the top lip of the Humpstor A at the middle To access cargo while using the Center Brace lift one end out of the hole and rotate the Center Brace out of the way Return Center Brace to hole when finished Note the Middle Latch does not need to be latched to secure lid Note Lid may need to be pressed down in order to close the latches when the seal is new Once the seal has formed to the lid it should close on its own Locking the Humpstor To lock Humpstor use one or more standard padlocks Insert lock thru the latch hole Note Lock only needs to go through one hole in the latch Page 4 Continued Exploded View Parts List Part Description Oty DU HA Humpstor 1 sme 1 NIC E mmu 1 Lr menm EN Pe mm fe Cu oromon EN MOM CT E i eme 1 Di sme 2 i wewsum 4 v emos 2 Cw Fewer EN o founo E Ce rmen E ACTICIN EN a Heron aise EN EMITAN EN MOMIA EN Lu resso EN raster 610 w fins EN
Download Pdf Manuals
Related Search