Du Ha 20025 Use and Care Manual
Contents
1. holding current plastic tray Remove tray from truck Wore If you experience problems removing bolts you may need to apply upward pressure from under the tray Remove jack Turn the DU HA upside down Using clear tape tape the two spacers directly over the pre drilled holes in the bottom front of the DU HA directly above the DU HA lettering Turn the DU HA back over Line up the DU HA so the pre drilled holes are directly above the holes in floor of the truck with the DU HA lettering facing forward Wote The spacers are designed to keep the back seat from hitting the DU HA when the seats are in their upright position If the seat still hits add extra washers Screw in each bolt using an 8mm socket Do not overtighten Re attach seat back in the same manner as removed using existing bolts and 13mm socket Re attach plastic covers Snap rear cover back into same holes and secure front cover with Phillips screwdriver If desired install foam organizer gun racks with plastic stiffeners by bending and snapping them into channel slots in DU HA Gun racks will hold two guns or one gun depending on how you install them Note You may place jack handles in the DU HA or on the floor in front of the DU HA Safety Instructions Warning Seat back must be latched up at all times while vehicle is moving Make sure the DU HA is secured in the vehicle according to installation instructions Do not store explosives or hazardous material2. Installation Instructions DU HA 00 07 Ford F 250 F 550 Super Duty Crew Cab amp Reg Cab Fits OU HA Part Numbers Behind the Seat Storage en 20025 20032 Materials Needed I 8mm Socket Installation Instructions Solid Bench Seat D Tilt the back of the rear seat forward Remove the jack handles from the current plastic tray if applicable Using an 8mm socket remove bolts holding current plastic tray Remove tray from truck Wote f you experience problems removing bolts you may need to apply upward pressure from under tray Turn the DU HA upside down Using clear tape tape the two spacers directly over the pre drilled holes in the bottom front of the DU HA directly above the DU HA lettering Turn the DU HA back over Line up the DU HA so the pre drilled holes are directly above the holes in the floor of the truck with the DU HA lettering facing forward Note The spacers are designed to keep the back seat from hitting the DU HA when the seats are in their upright position If the seat still hits add extra washers Screw in each bolt using an 8mm socket Do not overtighten If desired install organizer gun racks with plastic stiffeners by snapping them into the slots in the DU HA as pictured Gun racks can be installed to hold two guns or one gun depending on how you install them If you removed your jack handles from the existing tray you can place the jack handles in DU HA or on
3. floor in front of DU HA Safety Instructions Warning Seat back must be latched up at all times while vehicle is moving Make sure the DU HA is secured in the vehicle according to installation instructions Do not store explosives or hazardous materials in the DU HA Do not place loaded guns in the DU HA For further instructions refer to truck owners manual or contact DU HA Inc Part Description B Foam Organizer Gun Rack 2 N jaN g e D Spacers 13RS075009 3 4 x 5 T oi E Non Sirap wit Buckie 2 T a DU HA Inc website www du ha com phone 1 866 306 DUHA 3842 fax 1 218 998 4013 306 Saint Andrews Street South Fergus Falls MN 56537 Installation Instructions DU HA 00 07 Ford F 250 F 550 Super Duty Crew Cab amp Reg Cab Fits 0U HA Part Numbers Behind the Seat Storage an 20025 20032 Materials Needed Phillips Screwdriver 13mm Socket 8mm Socket Installation Instructions 60 40 Split Bench Seat D Tilt the backs of the rear seats forward On driver s side rear seat remove plastic cover located by seat bottom tilt lever using Phillips screwdriver then remove plastic cover from side rear portion of seat be careful not to break spring clips when removing ED Remove the two bolts holding the rear seat back using a 13mm socket then pull seat back forward Remove jack handles from current plastic tray if applicable Using an 8mm socket remove bolts
4. s in the DU HA Do not place loaded guns in the DU HA For further instructions refer to truck owners manual or contact DU HA Inc Part Description Oty La DU HA Storage Unit i B Foam Organizer Gun Rack 2 straps are included to help secure Plastic Stiffener guns gear in place oe Spacers 13RS075009 3 4 x 5 EB Nylon Strap with Buckle Note Underseat storage is also available for this Crew Cab model Visit www du ha com for more info DU HA Inc website www du ha com phone 1 866 306 DUHA 3842 fax 1 218 998 4013 306 Saint Andrews Street South Fergus Falls MN 56537
Download Pdf Manuals
Related Search