Knaack 42 Instructions / Assembly
Contents
1. NOTICE Any modification or unintended use of this product shall immediately If you have any questions or need to replace this decal please give us a call Call Toll Free 1 800 456 7865 void all manufacturers warranties Manufacturer disclaims all liability KNAACKO products are protected by one or more of the following patents or trademarks U S 6772613 945736 4288134 4290281 4383721 5076078 1182980 1182981 1182982 1182983 1266140 1517767 for injuries to persons or property resulting from any modification to 1560477 1897535 260062 2290111 Canada 1176681 280058 280798 281398 283281 U K 2172510 2233036 1390299 1392022 Australia 754069 754070 N Z 296048 296050 other patents pending or unintended use of this product KNAACK MANUFACTURING COMPANY KNAACK 420 E TERRA COTTA AVENUE CRYSTAL LAKE ILLINOIS USA 60014 815 459 6020 MANUFACTURING Master Lock is a U S registered trademark of Master Lock Company 2000 Knaack Manufacturing Company Rev C 9 04 Part No 14 0008 COMPANY American Lock is a U S registered trademark of American Lock Company A DANGER2. INSTALLATION INSTRUCTIONS WATCHMAN IV Lock System TOOL REQUIRED Ratchet Wrench with 1 2 Socket or 1 2 Combination Wrench NOTE This lock system is designed to be used with a Master Lock No 1 Master Lock No 5 or American Lock No 50 or an equivalent sized lock If you are using a padlock not listed above it is your responsibility to make sure the lock mechanism is working correctly Padlocks must meet ALL requirements listed in Figure 2 or Figure 3 1 Unbolt the padlock tab using a 1 2 socket or wrench Place the Latch Rod in LATCHED position as shown in Figure 1 Install 5 16 x 3 4 Carriage Bolt into correct hole in Padlock Tab install Padlock shackle into Padlock tab then secure to Lock Box using Locking Nut See Figure 2 or 3 Fiqure 2 For Installation of i For Installation of Figure 1 Master Lock No 5 American Lock No 50 Master Lock No 1 or or equivalent size E Shackle p FRONT CORNER OF BOX equivalent size 7 GAS POWERED _ m Shackle 5 16 EQUIPMENT 3 8 dia dia ee _1 3 16 to 11 32 or less EXPLOSIVES nd OQ dia 2 15 16 or ess i less k IS closed 7 8 to closed Ne En 1 7116 1 1 8 436 or more or more Latch Rod open open Figure 3 i onro gt gt rn 2 Padlock Tab 2 1 4 Lock max l Locking cen x 3 4 Do not put fuels flammables explosives or 4 Nut SD _ 5 oe 5 16 x 3 4 7 Ca
3. rr Bolt SD Locking hazardous materials inside these products Carr Bolt Q Use top Nut Gasoline solvents gun powder or other muni N hole only I Use to tions dynamite propane acetylene or other Padlock a p such products can explode if stored inside Use round Hole Tab nelson these products E for 3 8 dia IN Use square Use these products ONLY for storing and shackle Hole for 5 16 transporting electric or hand tools and I Master No 5 NOTE Carriage Bolt will seatinto Jia shackle equipment and other similar materials Lock Box American No 50 round hole when tightening Master No 1 Failure to follow these warnings or modification Locking Nut or other uses of these products could result in f TEST THE FUNCTION OF YOUR PADLOCK death serious injury or property damage If you have installed one of the padlocks listed above per the instructions you do not have to perform this test 2 Before locking the padlock open cover and slide Latch Rod into OPEN position If you are unable to move Latch Rod fully to OPEN position the lock you have DO NOT PAINT OVER OR REMOVE THIS DECAL installed is not acceptable for use see note above 3 Close the cover move Latch Rod to LATCHED position Lock padlock and try to move the Latch Rod to OPEN position and open the cover If you are able to move Latch Rod fully to OPEN position and open the cover the lock you have installed is not acceptable for use see note above
Download Pdf Manuals
Related Search