Kreg KMS7801 Instructions / Assembly
Contents
1. Red Curse Line Tape Lens2. ai SIO 0 Mi iy Our stops feature an adjustable lens curser similar to the lens on a quality tablesaw rip fence The lens is a clear material except for a red line curser on the bottom of the lens as shown in figure 6 The lens is adjustable to fine tune the stop and is secured in place with the Lens Screw The Lens can be aligned to either side of the stop arm The red line curser makes it easy to read the tape lines and fine tune the stop when compensating for blade thickness variations or a tape that is not perfectly positioned Please note that when placing the self adhesive tape onto the track it must be placed 1 4 CLOSER TO the saw blade to allow the Lens to function properly as shown in figure 7 cela ead een Red Line IMPORTANT NOTE Curser If you will be using the stops on a track that is not offset 1 4 simply remove the lens and read the meausrement directly off the edge of the stop ASSEMBLING AND ADJUSTING THE STOP Refer to the exploded diagram Figure 11 for parts identification Red Line Curser NOTE Read these instructions carefully To correctly use the stop lens the tape must be positioned 1 4 closer to the blade than the actual distance LOCATING THE MEASURING TAPE Kreg Flip Stop Cut a straight 3 4 thick scrap board exactly 24 long by 3 wide as in fig 8 Locate the board with one end against the teeth of the saw blade Use a squa
3. movement Lastly insert the lens into the lens slot Again place the 3 x 24 board against the saw blade Slide the edge of the stop arm into the edge of the board and adjust the lens curser to be located EXACTLY over the 24 mark on the tape Cut a test piece and check length with a tape measure 24 Board Nylon Lens Socket Screw 10 32 Set Screw The Flip Stop arm has a finger which is parallel to the flip arm The space between the flip arm and finger is 1 4 so it will accept a 1 4 20 bolt for attaching accesories such as the Miter Adapter KMS7831 as shown in Figure 12 MAINTENANCE OCCASIONALLY PLACE A DROP OF OIL BETWEEN THE ARM ANDTHE BASE TIGHTEN THE BOLT ENOUGH SO THAT THE ARM WILL FALL FROM ITS OWN WEIGHT AFTER THE BOARD IS WITH DRAWN Oil here 1 4 20 Bolt Knob Miter Adapter These KREG products are made in the USA and are protected by one or more of the following U S Patents 5 337 641 5 493 789 5 617 909 and 5 768 966 Other patent applications are pending or granted When using the stops on the HD trak the stop can be reconfigured to allow space for a zero clearance board as shown in Figure 13 Simply disassemble the stop and rotate the stop base 180 degrees Reassemble so the flipstop will project out further from the fence to accomodate the fence m KREG TOOL COMPANY Fi D 201 Campus Drive a Huxley lowa 50124 www kregtool com 800 447 8638 nuw kreg
4. re to place a pencil mark across the top of the fence 24 from the blade on either side of the 1 2 indentation for the stick on tape as shown in fig 9 Align the 24 1 4 mark of the stick on tape over the pencil mark and adhere the tape to the 1 2 trak indentation along the length of the trak IMPORTANT NOTE When reading the measurement from the lens curser the tape is off set 1 4 closer to the blade as shown in figure 10 To set correctly locate the tape so that the 24 1 4 mark is aligned with the 24 pencil mark on the trak extrusion PPP PEPE yr yp Ty 24 j 23 Knob Place the 1 1 2 hex bolt through the bottom of the stop base Slide the head of the bolt onto the trak groove and tighten with the black plastic knob Next push the 3 1 4 hex bolt and nylon washer into the stop arm Make sure the arm is assembled so that the arm is closer to the blade than the stop base Place the second nylon washer and the nylon locking nut onto the end of the 3 1 4 bolt and tighten until the stop arm is snug but still falls freely Place the 10 32 setscrew into the top of the stop arm and tighten Next place the nylon screw into the backside of the stop base and gently tighten it until the stop falls slowly with gravity when lifted You may need to adjust the tension on the 3 1 4 bolt or the tension of the nylon screw slightly for best performance A lubricant may also be added to enhance the stops ease of
5. tool com reg 800 447 8638 FLIP STOP KMS780O1 Top Trak KMS7712 Kreg Flip Stop Workpiece TENRA The Flip Stop measures and records the distance between the end of the board and the saw blade drill bit or router cutter This allows you to easily cut multiple pieces of stock to the exact same length Cutting numerous pieces to the exact length without measuring is easy Gently press the end of the board opposite the blade against the side of the stop arm as shown in figure 1 Miter Saw Shop Made Table Workpiece These stops can be secured anywhere along the track The curved flip arm is designed to raise auto matically when a board is pushed against the front of the stop arm as shown in figure 2 _ Stop Base Stop Tape Arm a VVVVANAN On The stop arm rests on top of the workpiece unti the board underneath it is removed When the board is removed or moved to the side of the stop the arm drops down and is again ready for use The stop arm can be positioned on either side of the base which is secured to the track with the knob The stop arm should be positioned between the base and the saw blade as shown in figures 1 and 2 The distance between the biade and the stop arm is measured off the tape on the top of the trak see the opposite side of this page for more instructions Red Curser Line Nylon Socket Red Curser Line
Download Pdf Manuals
Related Search