SentrySafe DH-134E Use and Care Manual
Contents
1. entered Always perform this operation with the door open Any Code Any Code to unlock 1 Enter Master Code 1 1 2 The lock will indicate a valid setting change with a single signal Master or Manager Code User Code to unlock 1 Enter Master Code 2 2 2 The lock will indicate a valid setting change with a single signal Time delay mode Always perform this operation with the door open This function will delay both the openi Activate time delay 1 Enter Master Code 01 99 01 99 2 The lock will indicate a valid setting change with a single signal Example Master Code 05 05 this will set a five 5 minute time delay 3 Press or to initiate the Time Delay Floor Mount optional This kit contains e Four 4 Masonry Anchors Required tools e Powered Drill e Adjustable Wrench e 1 2 in M12 Masonry Drill Instructions 1 Unlock safe and open door 2 Remove safe floor carpet 3 Look on the bottom of safe for four 4 holes with cap plugs Opening your safe in dual user mode 1 Enter 1st Code 2nd Code 2 The lock will indicate a valid code entry with a single signal and the open light will stay green for five 5 seconds 3 Turn the handle clockwise before the green light disappears When time delay is set During the time delay period the keypad will not respond to any entries The lock2. sentrySafe OWNERS MANUAL MANUEL DU PROPRIETAIRE MANUAL DEL USUARIO Depository Safes Depository Safes Depository Safes TABLE OF CONTENTS TABLE DES MATIERES NDICE Battery instalatii sssini oa 2 Batteninstalla toisessaa 2 Beatteryrinstallationissc sii stsccssscctavesatltavewveteststiscoseasaetwacieatereasctacteten 2 Programming the lock codes sesssssssssssesssssssssstsssecceseessssnnnnnnenes 2 Programming the lock codes sssssssessssssssesecsessssssnsnesseseeeesee 2 Programming the lock codes sssessssssssccessssssssnnnseeesceeesesenes 2 Dual USA MOJE naniii 3 Dualiuser Modes fester tewereseensdecncenseeedneatisenenieetac naan 32 DUAL USER MOG sienne n N 3 Time delay mode 3 Time delay mode Time delay mode First class customer care First class customer care First class customer care E 4 Serial No L 777777 Master Code OOOO Manager Code 2008 400440 Depository Safe Thank you for purchasing this security safe from Sentry Safe This guide is designed to maximize the user and security features of this project Getting started Installation of the batteries keep door open during setup 1 Turn the keypad housing counter clockwise and carefully pull away from the mounting plate to expose battery compartment 2 Install four new AAA Alkaline batteries not included Caution Hold onto the keypad housing to avoid pulling wires 3 Carefully positio
3. unlock e Make sure you are getting a valid response e Make sure you get a signal with every key stroke e Make sure you are not in time delay mode See time delay mode above e Replace the existing batteries with new ones See changing your batteries in troubleshooting If the lock still does not open contact Sentry Group Customer Care 1 800 828 1438 or 585 381 4900 Available Mon Fri 8 00 am 6 00 pm EST Follow the instructions carefully to get the best possible use from your lock
4. will flash once every five 5 seconds during time delay and will flash once every second during the last ten 10 seconds of the time delay ending with a double signal The lock will flash twice every five 5 seconds during the open period The open period length is two 2 minutes 4 Remove the cap plugs Position the safe in the desired location 6 From inside the safe mark the location of the four 4 bolt down holes 7 Move the safe aside to the clear marked spots for drilling 8 Using the 1 2 in masonry drill drill a 4 in deep hole in the marked locations 9 Replace the safe in the desired location with the holes in the safe aligned with the drilled holes in the floor Returning to single user mode Single code to unlock 1 Enter Master Code 0 0 2 The lock will indicate a valid setting change with a single signal ng and programming of the lock During the open period you can open your safe see How to open your safe Step 1 or program your safe following the steps of any programming procedure Deactivate time delay 1 Enter Master Code 00 00 2 The lock will indicate a valid setting change with a single signal 10 Pass each masonry anchor through the safe floor into the drilled holes making contact with the safe floor 11 Tighten each masonry anchor with the adjustable wrench 12 Replace safe floor carpet O Sentry Group Customer Care Tro
5. imes before closing the door Enter Code The lock will indicate a valid code change with a single signal e The lock will indicate an invalid code change with a double signal and the old code is still valid Changing the Manager Code Code length 1 to 10 digit code Always perform this operation with the door open 1 Enter Master Code or Manager Code 2 The set light will stay orange for ten 10 seconds 3 Enter 2 New Manger Code New Manager Code before the orange light disappears If a mistake is made during the change wait thirty 30 seconds and repeat steps 1 thru 3 Test the new code several times before closing the door Enter Code e The lock will indicate a valid code change with a single signal e The lock will indicate an invalid code change with a double signal and the old code is still valid Activate user codes Code length 1 to 10 digit code Always perform this operation with the door open 1 Enter Master Code or Manager Code 2 The set light will stay orange for ten 10 seconds 3 Enter User ID Number 3 7 New User Code New User Code before the orange light disappears If a mistake is made during the activation wait thirty 30 seconds and repeat steps 1 thru 3 The lock will indicate a valid code entry with a single signal e The lock will indicate an invalid code entry with a double signal and the
6. n the keypad into the inserts on the mounting plate and turn clockwise Ensure that there are no wires or cables trapped between the keypad and the mounting plate Pinched cables result in a short circuit 4 Enter Master or Manager Code from front of booklet Programming your lock codes The SentrySafe electronic lock is shipped from the factory with a factory set master code amp manager code see front of booklet You should set the lock to your own unique master amp manager code immediately Keep notes on which code belongs to which user Master User 1 Manager User 2 User 3 User 4 User 5 User 6 and User 7 A single signal LED flashes and beeps once response from the lock indicates valid entry A double signal LED flashes and beeps twice response from the lock indicates an invalid entry e If three incorrect entries are entered in a row the keypad will shut down for a period of five minutes During this shut down period you will not get a response from the keypad Changing the Master Code Code length 1 to 10 digit code Always perform this operation with the door open 1 Enter Existing Master Code 2 The set light will stay orange for ten 10 seconds 3 Enter 1 New Master Code New Master Code before the orange light disappears If a mistake is made during the change wait thirty 30 seconds and repeat steps 1 thru 3 Test the new code several t
7. old code is still valid The lock will indicate a valid code entry with a single signal and the open light will stay green for five 5 seconds 5 Turn the handle clockwise before the green light disappears Example Master Code or Manger Code 5 New User Code New User Code This will activate User Five 5 Changing the user code Always perform this operation with the door open 1 Enter User Code 2 The set light will stay orange for ten 10 seconds 3 Enter New User Code New User Code before the orange light disappears If a mistake is made during the change wait thirty 30 seconds and repeat steps 1 thru 3 Test the new code several times before closing the door Enter Code The lock will indicate a valid code change with a single signal The lock will indicate an invalid code change with a double signal and the old code is still valid The Master and Manager can also change the user codes by following the Activate user codes section steps 1 thru 3 Deleting user codes Always perform this operation with the door open 1 Enter Master Code or Manager Code 2 The set light will stay orange for ten 10 seconds 3 Enter User ID Number 3 7 Dual user mode When you want two people to open the safe set your safe to dual user mode One person enters their code and within sixty 60 seconds the second code is
8. ubleshooting Low battery warning The green LED light will signal in red when opening your safe The lock is giving you a valid signal but is not unlocking Changing your batteries 1 Turn the keypad housing counterclockwise and carefully pull away from the mounting plate to expose battery compartment 2 Remove the four AAA Alkaline batteries and replace Caution Hold onto the keypad housing to avoid pulling wires 3 Carefully position the keypad into the inserts on the mounting plate and turn clockwise Ensure that there are no wires or cables trapped between the keypad and the mounting plate Pinched cables result in a short circuit sentrySafe www sentrysafe com 900 Linden Avenue Rochester New York 14625 14625 2784 USA Telephone 585 381 4900 Customer Service 1 800 828 1438 8 am 6 pm E S T Monday Friday Fax 585 381 2940 The lock has no response no flash no beeps Make sure the wires in the keypad housing are not pinched and are securely connected See installation of batteries on page 2 Check to make sure the batteries are correctly and securely inserted into the battery compartment See installation of batteries on page 2 Lock can possibly be in the lockout penalty wait five 5 minutes and check if the lock responds Replace the existing batteries with new ones See changing your batteries in troubleshooting The lock is responding but does not
Download Pdf Manuals
Related Search