Husky H4860HSG Use and Care Manual
Contents
1. Please contact 1 888 43 HUSKY for further assistance 12 x Xs D 0 N S 8 9 RUS Pait yX 5 gt Urrin D D l O 24 17 4 6 CT 2 Ref Part Number Description Qty Ref Part Number Description Qty 1 9T2001 FP Air Cap 1 14 912012 1 O Ring 1 2A 9720021 4 mm Nozzle 1 15 9T2012 Fluid Control Knob 1 2B 9T20023 6 mm Nozzle 1 16 9T20091 Fluid Control Needle Front 1 2C 9T20022 8 mm Nozzle 1 17 9T20092 Fluid Control Needle Rear 1 3 9W98061 Retainer Ring 1 18 9120018 Trigger Pin 1 4 9120304 O Ring 1 19 912017 Air Inlet 1 5 9120302 FP Hopper Clamp 1 20 912023 Trigger Buckle 1 6 9120301 FP Hopper 1 21 9W240041 Fluid Seal Base 1 7 9T2005 FP Gun Body 1 22 91T2019 FP Trigger Lever 1 8 9720043 O Ring 1 23 9720024 Support Stand 1 9 9T20081 FP Fluid Control Bushing 1 24 9W7927 Wrench 1 10 9120082 Washer 1 25 9W7127 Soft Brush 1 11 972010 Fluid Control Spring 1 26 9D41A4105 Needle 1 12 912013 0 Ring 1 27 9D41A4103 Cleaning Brush 1 13 972011 Fluid Seal Bushing 1 HUSKYTOOLS COM2. cap and orifice with a rag moistened with thinner Reassemble the orifice and screw the air cap tight Intermittent spray The O ring is dry or worn out The air stem bushing is loose The material orifice is loosely installed or there is dirt between the orifice and body Back up the gun put a few drops of machine oil or replace with a new O ring Tighten the air stem bushing Take off the air cap and material orifice clean dirt and reassemble the orifice and tighten the air cap Unable to get a satisfactory spray The adjusting nut is improperly adjusted The air stem is sluggish Ensure the adjusting nut is in good condition Disassemble the adjusting stop assembly as per the instructions in the manual wipe a small amount of lithium based grease on the stem and O ring then reassemble There is dripping from the material orifice The material orifice and stem are worn out Replace with a new orifice and stem There is a thin sandy coarse finish There is a thick dimpled finish that resembles an orange peel Gun held too far from the surface Move the gun closer to the surface as per the instructions in the manual Service Parts
3. Maintenance Ensure the air line is shut off and drained of air before removing this tool from service This will prevent the tool from operating if the throttle is accidentally engaged DAILY CLEAN UP A NOTE Clean the spray gun immediately after use remaining material Disconnect the compressor When you have finished spraying shut off the compressor and disconnect the air line from the gun Drain remaining material into a bucket until most of the texture material is out of the hopper Fill the hopper with clean water Remove the nozzle from the gun and allow water to flow through and out of the gun Flush until the gun is clean Remove the hopper from the gun and finish cleaning all components A soft brush may be used to help loosen any dried on material from the surface Connect the air line to the gun Turn on the compressor Open the gun air valve forcing air through the tip to clear out any Troubleshooting Problem Possible Cause Solution Material does not flow from the hopper Unable to spray material or sprays inefficiently Unable to get a satisfactory atomization Soak the material orifice in solvent to loosen the clog Trigger the material orifice several times Take off the air cap and material orifice clean the orifice using a bamboo or wooden toothpick Then wipe off the air
Download Pdf Manuals
Related Search