Universal Hardware 4014 Instructions / Assembly
Contents
1. A j TAPE HINGE A OPPOSITE TAPE BN ince OPPOSITE 3D MAIN ARM ADJUSTING SCREW 3D ATTACHING MAIN ARM TO BODY NOTE Speed adjustment valve on closer body must be positioned towards the door hinge Place main arm onto the BOTTOM spindle of the closer body for an outward opening door and attach ADJUSTING SCREW MANA opening door and attach with hex screw lock HINGE with hex screw lock washer and flat washer washer and flat washer 3E ATTACHING BODY 3E 3E 3E ATTACHING BODY Position closer body with Position closer body with main arm attached over main arm attached over the the drilled holes on the o SER A drilled holes on the jamb fain aie E os attached mustbe on he main arm attached musi be on the top Fasten WOOD OR bottom Fasten closer to closer to door using SELF TAPPING door using screws for either SCREWS i screws for either wood or wood or aluminum door aluminum doors jambs 3F ATTACHING 3F FOREARM 3F 3F ATTACHING FOREARM AND SHOE EAREN z CONNECTIN FOREARM AND SHOE ASSEMBLY C SCREW ASSEMBLY Position the forearm shoe over holes on the top door jamb and fasten using screws for SCREWS Position the forearm shoe over holes on the door and fasten using screws for either wood or aluminum either wood or aluminum doors doo2. desired degree opening 3B MARKING HOLE LOCATION Use a hammer and punch to mark the center of each screw hole then remove the template Left Hand Door template 2 Right Hand Door template 1 3C PREPARING SCREW START HOLES front of this sheet TAPE er a Wood Door assembly 3 1 1 4 deep assembly 3 1 1 4 deep b Aluminum or Steel Door 3 4 deep 3D ATTACHING MAIN ARM TO BODY NOTE Speed adjustment valve on closer body must be positioned towards the door hinge MAIN ARM 3D SCREW Place main arm onto the TOP spindle of the closer body for an inward NOTE Numbers in parentheses indicate the item number shown in Parts and Assembly Diagram on the Soft Wood use a 1 8 drill bit and drill four holes for the closer body 1 and two holes for the forearm and shoe Hard Wood use a 5 32 drill bit and drill four holes for the closer body 1 and two holes for the forearm and shoe Use a drill with a 5 32 bit and drill four holes for the body 1 and two holes for the forearm shoe 3 approximately The templates are in two parts Cut out the right or left hand templates marked OUTWARD OPENING Tape the closer body and forearm shoe templates following the template instructions for desired degree opening Right Hand Door template 3 Left Hand Door template 4
3. UNIVERSAL HARDWARE The Professional s Choice BEFORE STARTING THE INSTALLATION DOOR CLOSER UH4013 or UH4014 INSTALLATION INSTRUCTIONS Compare the requirements of the installation with the specifications below to make sure the correct model of CLOSER will be installed Type nae Maximum door width 38 Maximum door weight 140 Ib Maximum open angle 120 body mounted on door 155 1 PARTS AND ASSEMBLY DIAGRAM Tools needed for installation Hammer 2 Phillips Head Screwdriver 1 8 and 5 32 drill bits Punch Drill amp Tape Check that all parts shown in the parts list and in the illustration are present Match screw size and type to hardware drawing Name of Parts 1 Body Qty Main Arm Forearm and Link Arm Shoe Main Arm Screw Hex Head Lock Washer amp Washers Phillips Oval Head Wood Screw 10 x 1 1 4 2 3 4 5 Forearm Screw Pan Head Lock Washer amp Washers 6 T Phillips Oval Head Self Tapping Screw 10 32 x 3 4 8 ajlolo a a Body Cover FOR WOOD FORA OR For Body lt and Link Arm Shoe SCREWS SHOWN ACTUAL SIZE STEEL 7 LUMINUM 2 LOCATION OF CLOSER ON THE DOOR Determine whether the door is left or right hand using the following illustrations Remember that the CLOSER is always mounted inside the building near the hinge
4. e slot in the adjustment screw is parallel to the door For a slower latching speed the slot in the adjustment screw is perpendicular to the door x O 5 ATTACH COVER cc O Q D Slide cover 8 onto body 1 3 O 6 INITIAL OPENING POWER ADJUSTMENT g Adjusting foot for opening power see illustration on right m ADJUSTING 2 SCREW STANDARD POSITION For Customer Care call Toll Free 800 562 5625 or info hamptonproducts com
5. edge of the door 2A INWARD OPENING DOOR This illustration shows the mounting for inward opening doors as seen from inside the building 2B OUTWARD OPENING DOOR This illustration shows the mounting for outward opening doors as seen from inside the building RIGHT HAND DOOR 3 INSTALLATION PROCEDURE LEFT HAND DOOR RIGHT HAND DOOR LEFT HAND DOOR Perform each of the following seven steps in sequence 3A POSITIONING TEMPLATE Templates to help position the CLOSER correctly are provided on an enclosed sheet BE SURE TO USE CORRECT TEMPLATE For installation of model UH4013 or UH4014 decide the maximum opening angle for the door 120 or 155 before cutting out the template The template must be cut differently for each angle 2015 Hampton Products International Corp 50 Icon Foothill Ranch CA 92610 3000 USA For Customer Care call Toll Free 800 562 5625 or info hamptonproducts com www universalhardware com 1 800 562 5625 91000_UH4013 14_REVA 95047000 02 15 UNIVERSAL DOOR CLOSER UH4013 or UH4014 INSTALLATION INSTRUCTIONS HARDWARE The Professional s Choice INWARD OPENING DOORS OUTWARD OPENING DOORS Cut out the right or left hand template marked INWARD OPENING Tape the template to the upper edge of the door on the hinge side following template instructions for
6. r jambs Z WOOD OR CONNECTING SELF TAPPING SCREW SCREWS CLOSING SPEED CONTROL 3G CONNECTING MAIN ARM TO FOREARM Adjust length of forearm to position the forearm at a right angle to ATTENTION ADJUST CLOSING SPEED 3G ADJUSTING LENGTH OF FOREARM T TIME TO BETWEN 4 amp 6 frame when connected to main arm at the elbow Use washer and ee eae SECONDS FROM 90 ei z eee _ vay screw 4 provided to secure the pivot connection Tighten forearm LATCH 40 E DOORS USED BY locknut HANDICAPPED ELDERLY i P OR SMALL CHILDREN MAY Important When door is fully closed and the forearm is at a 90 oa REQURE LONGER degree angle to the door this position creates pressure which CLOSING TIMES forces the door closed vt CAUTION DO NOT BACK 4 SPEED ADJUSTMENT aaia Closer speed is factory set If a different speed is desired both sweep and latch speed can be adjusted by a single screw adjustment STANDARD L CLOSING CYCLE 4A SWEEP SPEED ADJUSTMENT Turn speed adjustment screw clockwise 1 turn for a slower speed ADJUSTING FOOT FOR INITIAL OPENING POWER MOVE FOOT PIVOT TO HOLE AS ILLUSTRATED SWEEP SPEED MAINA and counter clockwise 1 turn for a faster speed Do not exceed two LESS POWER MORE POWER 4A ADJUSTMENT 4B LATCH SPEED turns in either direction ADJUSTMENT 4B LATCHING SPEED ADJUSTMENT For fastest latching speed th
Download Pdf Manuals
Related Search