Kwikset 915TRL TSCR 11P UL Instructions / Assembly
Contents
1. mY EDN ll rar If you press the wrong digit while entering a user code you can press the Lock symbol once to clear the digits entered previously and immediately restart the code entry process Install the battery cover ball tip SecureScreen SecureScreen is an added security feature that displays random digits before you enter a user code to unlock the door This feature ensures that there are fingerprints on all digits so that codes cannot be identified by examining the touchscreen for finger prints If desired this feature can be disabled by turning switch 4 to the off position See Switches on page 4 Keep G in a safe place as you will need it to access the back panel for additional programming SmartCode at a Glance Exterior Touchscreen Reference Guide Interior cover removed System Alerts Display Alert Reason Solution X pattern flashes one time with one beep One incorrect code entered Re enter code X pattern flashes three times with three beeps No user code programmed Program at least one user code Programming timeout after 20 seconds Attempt programming procedure again Program Unsuccessful programming button Checkmark symbol Re enter code after 60 second touchscreen lockout Three incorrect codes entered within one minute X pattern flashes 15 times with 15 beeps Sw2. x Fee gH z ae Make sure turnpiece is in the vertical position Make sure turnpiece shaft is rotated as shown Do not install batteries until step 5 Alarm will sound if battery is installed before cable is connected 5 Install the batteries and perform the door handing process This step will teach your lock the orientation of your door and is crucial to lock operation A Install 4 AA batteries in battery pack B Make sure the door is open and insert the battery pack A Ensure correct polarity For best results use new non rechargeable Alkaline batteries only 2 4 installation Cable goes underneath latch R Keep parallelto se edge of door H r Tighten Q 2x Install interior assembly onto mounting plate Ensure tight cable Lay excess cable fl connection O A Support exterior assembly during mounting plate bottom of the interior housing oute cable through center hole then push cable into bottom hole Insert key and test latch If latch does not extend or retract smoothly adjust screws Q Remove key when finished and make sure the latch bolt is fully extended at inside the C After a few seconds the latch bolt will retract and extend on its own to learn the orientation of the door Th
3. 61055 01 Parts in the box Latch Exterior Interior 915 Touchscreen Assembly a zZ TOUCHSCREEN ELECTRONIC DEADBOL W Installation and User Guide Mounting Fasteners Plate B is not included If needed m please contact Kwikset to order N bo P fiama a drive in latch for your lock Required tools Adapter Allen Q R S Bi _ i nmg A G comm p 4 AA Batteries Ruler Phillips head screwdriver Kwikset lt I bp poo 1 800 327 5625 pom Additional Tools depending on application www kwikset com Strike Keys SmartKey Tool mo gt H A Te Uj Hammer Wood block J 1 Prepare the door and check dimensions If drilling a new door use the supplied template and the complete door drilling instructions available at www kwikset com doorprep Measure to confirm that the hole in the door is either 2 1 8 54 mm or 1 1 2 38 mm Measure to confirm that the backset is either 2 3 8 or 2 3 4 60 or 70 mm C Measure to confirm that the hole in Measure to confirm that the door is the door edge is 1 25 mm between 1 3 8 and 2 35 mm and 51 mm thick 2 3 8 or 2 3 4 Pank 60 or 70 mm St 1 3 8 2 35 51 mm X MEN W Note Additional door preparation may be required for doors with 1 1 2 38 mm holes Consult the deadbolt drilling instructions at www kwikset com doorprep 2
4. Install the latch and strike A Isthe door edge chiseled B Hold the latch in front of the door hole with the latch D Which latch are you installing face flush against the door edge YES NO Latch A Latch B chiseled or Q 8 not chiseled Use latch A If the latch bolt is not already extended extend the latch bolt as shown Use latch B not included If the latch bolt is not already extended extend the latch bolt as shown C No adjustment is required Proceed to next step 1 4 Are the latch holes centered in the door hole Rotate latch face as shown to extend latch NO E Install strike on the door frame Make sure the hole in the door frame is drilled a minimum of 1 25 mm deep Longer screws install closest to the door jamb 3 Install the exterior touchscreen A What is the diameter of the hole in the door C Install exterior touchscreen and mounting plate Diameter is 2 1 8 Diameter is 1 1 2 54 mm 38 mm c is required for installation C is not needed for Install C on E installation Discard C YE B Locate screws for step 3C and keep them within reach o gt o perewsievenly 4 Install the interior assembly A Remove battery cover and battery pack from interior assembly B
5. automatically re locks door 30 seconds after button once more unlocking Disabled if no codes are programmed SecureScreen feature displays random digits to be pressed before entering user code This added security feature ensures that there are fingerprints on all digits so that codes cannot be identified by examining the touchscreen for fingerprints Success Failure If the touchscreen indicates a failure see the online Programming and Troubleshooting Guide Blinking red Low battery Deleting a single user code Factory Reset Note All codes may be deleted at once if the mastercode is enabled For more information about the A factory reset will delete all codes associated with the lock mastercode consult the online Programming and Troubleshooting Guide 1 Remove battery pack E a el 2 Press and HOLD the Program button while reinserting the battery pack Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red 4 Enter user code to be deleted 3 Press Lock symbol once 2 Press Checkmark symbol once 1 Keep door open Press Program button once Status LED 4 After a few seconds the lock will initiate the door handing process and the latch bolt will extend and retract to learn the orientation of the door 7 Press Lock symbol once 5 Press Lock symbol once 3 Pres
6. is is called the door handing process and it is crucial to lock operation will indicate Success flashing check symbol and si column of digits Once the door handing process is complete the touchscreen success or failure Failure mark flashing ngle X pattern D If the touchscreen indicates a failure attempt this procedure again If the door handing process is still unsuccessful after a second attempt consult the Programming and Troubleshooting Guide on the SmartCode 915 page at www kwikset com Add user codes Programming Timeout During programming if the screen is not pressed for 20 seconds the system will time out indicated by three beeps and the X pattern flashing three times and you will need to restart the procedure A Make sure the door is B open Press the Program button once Press checkmark C symbol once Enter user code A total D of 16 user codes may be programmed Each user code must be a unique code between 4 and 8 digits E Did you see the checkmark symbol illuminate with one beep or see the X pattern flash with three beeps Checkmark symbol with one beep Programming was successful Press lock symbol once X pattern with three beeps Programming was unsuccessful Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt Make sure the lock has room fo
7. itches Status LED Checkmark and lock symbols eo Turnpiece flash simultaneously five _ Low battery Replace batteries SmartKey tool hole shaft times with five beeps n Checkmark and lock symbols alternate flashing five times with five beeps Door jammed while attempting Manually re lock door If needed to lock reposition strike Note When the cover is removed the turnpiece shaft can be used to manually lock and unlock the door Remove battery pack reconnect the interior to the exterior then replace battery pack Interior assembly is Lock beeps continuously disconnected from exterior Beeping sound will only be heard if switch 3 is on Switches and Status LED Colors Manual Door Handing If needed the door handing process can be initiated manually This is useful if the lock is being moved to a different door Switches wtb On Off 1 Remove battery pack 2 Press and HOLD the Program button while reinserting the battery pack Release button once battery pack is installed The status LED will flash red and green 1234 Status LED Switch Function Color Lock Status Door lock status LED blinks every 6 seconds Blinking green Unlocked 4 The latch bolt will extend and retract to learn Audio mOn the orientation Blinking amber Locked of the door 3 Press the Program Lock
8. r an additional code If all user code positions are filled delete a code to make room for this one Beeping sound will only be heard if switch 3 on the lock interior is in the on positon See Switches and Status LED Colors on page 4 Mastercode For enhanced security a mastercode may be used when adding and deleting user codes For more information about the mastercode download the Programming and Troubleshooting Guide on the SmartCode 915 page at www kwikset com Test the lock review normal operation Confirm that the code s added in step 6 can unlock the door Activating the Screen Locking the Door Option 1 Option 2 Option 3 1 Activate the screen Touch screen with Touch lower left Touch screen 2 Press Lock symbol palm or back of hand until digits illuminate area of screen where checkmark is located until digits illuminate Note If no user codes are programmed the door cannot be locked via touchscreen with three or more fingers until digits illuminate A Re key the lock if needed and install the battery cover Re key the lock if needed B IMPORTANT Re key the lock Reinstall Remove battery to work with your battery pack before existing key See pack re keying the supplied SmartKey Re key instructions for more information fa 3 4 Unlocking the Door 1 Activate the screen 2 If SecureScreen is enabled touch the random digits that appear 3 Enter user code
9. r other security professional 2015 Spectrum Brands Inc
10. s the Program button once more The status LED will flash green and red several times If unsuccessful Make sure to enter the same valid code in steps 4 and 6 Test code While the door is open test the user code to make sure it no longer unlocks the door If the screen is not pressed for 20 seconds the system will time out and you will need to restart the procedure Important Safeguards Read all instructions in their entirety Familiarize yourself with all warning and caution statements Remind all family members of safety precautions Protect your user codes and mastercode Dispose of used batteries according to local laws and regulations CAUTION Prevent unauthorized entry Since anyone with access to the back panel can change the user codes you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge The use of a mastercode can help protect your system s settings WARNING This Manufacturer advises that no lock can provide complete security by itself This lock may be defeated by forcible or technical means or evaded by entry elsewhere on the property No lock can substitute for caution awareness of your environment and common sense Builder s hardware is available in multiple performance grades to suit the application In order to enhance security and reduce risk you should consult a qualified locksmith o
Download Pdf Manuals
Related Search