Baldwin 5080.102.PASS Instructions / Assembly
Contents
1. GE 3 At the screw marks drill 2 1 8 dia pilot holes for the screws Bore 7 8 dia X 3 4 deep hole 7 8 EDGE BORE 1 8 PILOT HOLES FOR 8 SCREWS 3 Attach the roses by screwing the threaded retainer onto the adaptors Orient the rose as desired and securely tighten by using the spanner tool For 5 amp 10 roses ensure rose is paral lel with door edge and drill 3 32 x 1 2 deep pilot holes at marked locations Install 8 oval head screws into door SPANNER TOOL 4 Chisel out the area marked in Step 2 to a depth of 1 16 or until strike is flush with door frame Install strike using 2 8 Flat Head combination screws 4 Orient the knob or lever so the set screw is pointed down amp toward the hinges of the door Slide the knob or lever onto the end of the spindle until it touches the adaptor and secure with set Screw PASSAGE LATCHSET INSTALLATION 2 Install the inside adaptor This adaptor will have thru holes for the flat head screws to fit into 1 With backset marking facing up grasp the faceplate and rotate to assure bevel side of latchbolt faces jamb slide the latch into the door as shown and secure with 2 8 3 4 combination screws BACKSET MARKING FACE PLATE INSIDE PRIVACY LATCHSET INSTALLATION 1a With backset marking facing up grasp the faceplate and rotate to assure bevel side of latchbolt faces j2. PK 2716 Note 8 Oval Head Screws are not required on 3 rose styles ROSE OUTSIDE 3 ADAPTOR BALDWIN X FAT FLAT HEAD SET SCREW LATCH ASER SCREWS ROSE 5 amp 10 roses may be installed as shown 8 X 3 4 COMBINATION 8 X 3 4 OVAL SCREWS HEAD SCREWS l i yn See note Interior Latchset STRIKE RETAINER PLATE PLATE THREADED STUD NYLON WASHER Privacy Version 78 A i PRIVACY Se Installation Instructions BUTTON wor Passage Privacy Full amp Half Dummy ALIGNMENT A O aaa 2 BUSHING EMERGENCY KEY NU PRIVACY BUTTON PRIVACY VERSION ALLEN PRIVACY VERSION WRENCH DOOR PREPARATION PASSAGE amp PRIVACY LATCHSETS ONLY 1 Fold the template on the line and locate on at desired height about 40 from floor Place folded edge on low Side of door bevel Mark holes on door for appropriate backset rose style and size FLL LL TEMPLATE BACKPLATE Yeo FLAT HEAD SCREWS RETAINER 2 Caution Recheck bore hole locations before drilling Drill the 2 1 8 Face Bore through the door first Drill the 1 diameter Edge Bore through to the inside of the 2 1 8 Face Bore For 5 amp 10 rose styles mark but do not drill pilot holes for 8 surface mount screws This will be done in a later step I Ty 3 Insert the latch into the edge of the door Trace an outline of the faceplate onto the d
3. amb From the side of the latch that will be inside the room push in the privacy lug On the other side of the lug install either an oval spacer or round spacer depending on lug shape with provided screw The side with the spacer should be facing outside of the room after install with the backset marking facing up Follow steps 1 thru 5 in the Passage Latchset Installation section before proceeding to step 2 BACKSET MARKING MUST BE FACING UP FLAT HEAD SCREWS 8 X 3 4 OVAL HEAD SCREWS See note SPINDLE SET SCREW BACKPLATE BACKPLATE RETAINER Note 8 Oval Head Screws are not required on 3 rose styles Consumer Help Line 1 800 566 1986 3 Install the outside adaptor Insert the flat head screws through the inside adaptor and into the outside adaptor Do not fully tighten at this time OUTSIDE ADAPTER 1b If the privacy latch Set is being installed on a 1 3 4 thick door thread the privacy but ton extension onto the privacy button before proceeding to step 2 PRIVACY PIN Pi PRIVACY PIN 1 Locate the position for hole in door If not used with a double door the hole location should be approx 40 from floor Drill a 1 2 hole through door BACKSET DIMENSION 2 3 8 OR 2 3 4 DOOR EDGE 4 Insert the spindle into the latch with the ends protruding from both adaptors Slide the alignment bushings onto the spindle ends and into the ad
4. aptors Tighten the screws and remove the alignment bushings 2a SPINDLE ALIGNMENT Vin f P BUSHING lt ALIGNMENT BUSHING 2 Insert the privacy pin into the hole on the inside rosette and thread into the latch 2 Place backplate on door so that the flat surface is toward the floor The flat surface should be parallel to the floor and perpendicular to the door edge A builder s square should be used for best results Using the backplate as a template mark center locations for 3 screw holes Remove backplate and pre drill 3 holes for screws 12 deep using a 1 16 drill bit Install backplate with 3 flat head screws provided Repeat for both sides of door IMPORTANT Before drilling 1 16 holes ensure the spindle can insert into one backplate and out of the other at marked position MARK LOCATION OF HOLES DOOR EDGE DOOR EDGE 5 Remove the spindle Attach the roses by screwing the threaded re tainer onto the adaptors Orient the rose as desired and securely tighten by using the spanner tool For 5 amp 10 roses ensure rose is parallel with door edge and drill 3 32 x 1 2 deep pilot holes at marked locations Install 8 oval head screws into door SPANNER TOOL Vay ZH l x RETAINER 3 Insert the spindle into the rose so the end of the spindle with stops is on the same side of the door as the privacy button The spindle V gr
5. hnology physical vapor deposition to create a finish highly resistant to the effects of weather and normal wear and tear The Limited Lifetime Finish Warranty on Lifetime Finish products covers the original purchaser for as long as you own your home Limited Finish Warranty The finish on Baldwin products excluding Lifetime Finish and living finish products is protected by a durable topcoat designed to maintain the beauty and quality of the Baldwin product The Baldwin Limited Finish Warranty covers the original purchaser for five years from date of purchase for interior use and one year for exterior use Living Finishes Due to the nature of Baldwin living finish products they will wear over time and may already have begun the process before reaching your home No finish warranty is offered on living finish products which are designed to age and improve over time Living finishes include raw brass oil rubbed bronze stainless steel and other non lacquered or non PVD finishes Refer to www baldwinhardware com for a complete warranty statement 2011 Baldwin Hardware Corporation Lake Forest CA 92610
6. oor edge Mark screw hole center locations and drill 1 8 pilot holes 8 X 3 4 OVAL HEAD SCREWS See note KNOB SET SCREW Note 8 Oval Head Screws are not required on 3 rose styles 4 Chisel out the area marked in step 3 to a depth of 5 32 or until faceplate is flush with door edge Proceed to Passage or Privacy installation 1 Locate the posi tion for hole in door If not used with a double door the hole location should be approx 40 from floor Drill a 5 8 hole 14 deep one Side of the door DO NOT DRILL THROUGH DOOR BACKSET DIMENSION 2 3 8 OR 2 3 4 DOOR EDGE STRIKE PREPARATION PASSAGE amp PRIVACY LATCHSETS ONLY 1 Using the strike portion of the marking template locate and mark strike mounting screws and centering points for your door thickness 2 Align the strike and trace outline onto the door frame using mounting screw marks for location 2 Place backplate on door so that the flat surface is toward the floor The flat surface should be parallel to the floor and perpen dicular to the door edge A builder s square should be used for best results Using the backplate as a template mark center locations for 3 screw holes Remove backplate and pre drill 3 holes for screws 2 deep using a 1 16 drill bit Install backplate with 3 flat head screws provided MARK LOCATION OF 3 SCREW HOLES DOOR EDGE ed DOOR ED
7. oove will be positioned down and towards the hinges of the door OOVE ON BOTTOM TOWARDS HINGES ON FOLLOW STEPS 5 THRU 7 OF PASSAGE LATCHSET INSTALLATION FOR ATTACHING THE ROSE SPINDLE amp KNOB OR LEVER 7 Slide a nylon washer onto the base of both knobs or levers Slide the spindle with the previously attached knob or lever into the latch with the set screw pointed down and toward the hinges of the door Secure the other knob or lever to the exposed spindle end 6 Insert the spindle into a knob or lever Align scribed mark with correct door thickness and secure with set SCrew 1 3 4 1 3 8 a o SET SCREW a D pg K i SPINDLE 5 slide nylon washer onto base of other knob or lever Install knob or lever onto spindle on the inside Secure with set screw pointed down and towards the hinges of the door 4 Slide nylon washer onto base of knob or lever Install knob or lever onto spindle on the outside Secure with set screw pointed down and toward the hinges of the door WARRANTY INFORMATION Limited Lifetime Mechanical Warranty Baldwin warrants that each Baldwin product shall be free from mechanical defects at the time of delivery and for the lifetime of the product or as long as you own your home Limited Lifetime Finish Warranty The Baldwin Lifetime Finish uses advanced finishing tec
Download Pdf Manuals
Related Search