Grip-Rite GRTFR83 Use and Care Manual
Contents
1. 9 Ibs 3 1 kg TOOL LENGTH 21 7 55 1 cm GRTFR83L 22 1 56 1 cm TOOL HEIGHT 12 4 31 5 cm TOOL WIDTH 4 5 11 4 cm TRIGGER TYPE SELECTABLE SEQUENTIAL OR BUMP FIRE AIR INLET MALE SWIVEL QUICK CONNECT COUPLER LUBRICATION 10W Air Tool Oil Provided NOISE CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 3774 ISO 11201 A weighted single event sound pressure level at operator s position LpA 1s 93 dBA A weighted single event sound power level LwA 1s 102 dBA A weighted single event surface sound pressure level LpA 1s 89 dBA VIBRATION CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 8862 1 Weighted root mean square acceleration 3 6 m s For best results use Grip Rite collated fasteners GRTFW83 FASTENER SELECTION CHART Size Box Shank Bright Galvanized 2 x 113 Smooth GR03 GR05G GR05HG 2 x 113 Ring GR04 GR04G GRO4HG 2 3 8 x 113 Smooth GR07 GR09G GR09HG 2 3 8 x 113 Ring GRO8R GR08G GRO6RHG 2 3 8 x 148 Smooth GR8D148 GR8D148HG N A 3 x 120 Smooth GR301 GR301G GR301HG 3 x 120 Ring N A GR408G GR408HG 3 x 131 Smooth GR014 N A N A 3 1 4 x 120 Smooth GR444 GR444G GR444HG 3 1 4 x 131 Smooth GR024 GR034G GR034HG 3 1 4 x 148 Smooth GR314148 N A N A SAFETY SAFETY LABELS These pneumatic fastening tools include a warning labe2. THE TOOL AIR INLET OPENING zT al en I 2 Use of a non relieving air coupling on the tool can trap air inside the tool housing and allow the tool to drive a fastener even after the air hose has been disconnected SAFETY SAFETY INSTRUCTIONS DO NOT ATTEMPT TO OPERATE THE TOOL IF THE A TOOL S OPERATING CONTROLS HAVE BEEN MODIFIED SAL OR ARE NOT WORKING PROPERLY Attempting to use a tool with modifed or malfunctioning trigger or workpiece contact can result in a fastener being driven unintentionally USE CORRECT FASTENERS Only use the correct fastener for the tool Using fasteners with incorrect specifcations can jam the tool or cause serious injuries USE THE CORRECT FASTENERS FOR THE APPLICATION Using the wrong fasteners can cause the workpiece to split and allow the fastener to fy free KEEP TOOL POINTED IN A SAFE DIRECTION WHEN LOADING FASTENERS Never point the tool at yourself or anyone else when loading fasteners DO NOT LOAD TOOL WITH TRIGGER OR WORKPIECE CONTACT DEPRESSED Depressing the trigger or workpiece contact during loading can result in an unintentional fastener drive if both devices are accidentally actuated at the same time KEEP FINGER OFF TRIGGER UNTIL TOOL IS IN POSITION TO DRIVE A FASTENER An unexpected bump or sudden contact with your body or that of a bystander can result in serious injuries AVOID DRIVING FASTENERS INTO KNOTS ON TOP OF OTHER FASTENERS AT WORKPIE
3. other than a proprietary PRIMESOURCE service warranty center or authorized service warranty center Non GRIP RITE TOOLS GRIP RITE COMPRESSORS parts have been used The tool has suffered any physical damage due to the use of non PRIMESOURCE approved fasteners Repairs are required due to normal wear amp tear The tool compressor has been inadequately packaged leading to damage in transit to the service warranty center Approved fasteners include the following brands GRIP RITE FAS NERS FAS NERS UNLIMITED IN NO EVENT SHALL PRIMESOURCE BE LIABLE FOR ANY INDIRECT ACCIDENTAL OR CONSEQUENTAL DAMAGE FROM THE SALE OR USE OF THESE PRODUCTS THIS DISCLAIMER APPLIES BOTH DURING 8 AFTER THE TERM OF WARRANTY THIS IS OUR WARRANTY amp IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILTY AND FITNESS FORA PARTICULAR PURPOSE EXCEPT AS MAY BE OTHERWISE PROVIDED BY LAW This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state 30 WARRANTY PNEUMATIC TOOL COMPRESSOR SERVICE INFORMATION Should any mechanical problems develop during the life of your equipment the following options are available for service and parts Call 800 676 777 where you will be routed to the nearest GRIP RITE distribution center and directed to the nearest authorized service warranty center Logging on to our website at ww
4. 22 ITEM P N DESCRIPTION1 GRTN7080 Hex Soc Hd Bolt 2 GRTN6660 Defector 3 GRTN7060 Hex Soc Hd Bolt 4A GRTN6670 Cap Assembly 5 GRTN6680 Gasket 6 GRTN220 Washer 7 GRTN6710 Spring 8 GRTN6690 Piston Stopper 9 GRTN2420 O Ring 10 GRTN2160 O Ring 11 GRTN6700 Piston Head Valve 12 GRTN7010 O Ring 13 GRTN6620 14 GRTN6610 lve 15 GRTN6630 16 GRTN2200 17A GRTN6730 18 GRTN2460 19 GRTN250 20 GRTN240 21 GRTN2430 22 GRTN6720 23 GRTN2190 24 GRTN6740 25A GRTN6750 26 GRTN4430 27 GRTN6760 28 GRTN6770 29 GRTN6990 30 GRTN6970 31 GRTN4180 32 GRTN4190 33 GRTN2220 34 GRTN800 35 GRTN2240 36 GRTN2100 37 GRTN6250 38 GRTN805 39 GRTN2170 40 GRTN830 41 GRTN2230 42 GRTN810 43 GRTN820 44A GRTN6780 Piston Head Valve Seal Piston Head Retaining Ring O Ring Driver Assembly O Ring Cylinder Hold Down Seal O Ring Cylinder O Ring Bumper Body Assembly O Ring End Cap Belt hook O Ring Washer Belt Hook Cover Belt hook C ring O Ring Valve O Ring O Ring O Ring Valve Plunger O Ring Spring O Ring Plunger Plunger Cap Trigger Assembly ITEM P N 46 47 53 GRTN2530 GRTN2550 GRTN790 GRTN6960 GRTN2210 GRTN7000 GRTN6790 GRTN2010 GRTN6810 54A GRTN7200 55 56 57 GRTN2660 GRTN6840 GRTN6850 58A GRTN6820 73 Assembly GRTN1530 GRTN6600 GRTN6640 GRTN6890 GRTN7070 GRTN6900 GRTN7210 GRTN7220 GRTN2210 GRTN6650 GRTN7040 GRTN7230 GRTN7240 GRTN7050 GRTN6930 74A GRTN
5. 7250 75 76 77 78 79 80 81 82 83 84 85 86 87 88 GRTN6950 GRTN7020 GRTN2710 GRTN6070 GRTN6920 GRTN6050 GRTN3340 GRTN4020 GRTN6050 GRTN7090 GRTN7030 GRTN7040 GRTN6830 GRTN7130 GRTFR83L PARTS LIST DESCRIPTION45 Spring Pin Spring Pin Pin Trigger Guide Safety Lever Grommet O Ring Nose Hex Soc Hd Bolt Spring Safety Upper Safety Lever Assy E ring Adjusting Nut Adjusting Spring Lower Safety Lever Rubber Pad Door Hinge Pin Spiral Spring Roller Pin Pusher Safety Lock Out Carriage Grommet Spring Hex Soc Hd Bolt Nail Guide Liner Nail Guide Liner Hex Soc Hd Bolt Stopper Magazine Assembly Magazine Cover Flat Washer Cap Locknut Hex Soc Hd Bolt Bracket Flat Washer Locknut Hex Soc Hd Bolt Flat Washer Hex Soc Hd Bolt Flat Washer Hex Soc Hd Bolt Safety Cap Flat Washer GRDAK2300 GRRBK2300 GRTFR83MAN GRTRK100 coU Driver Assembly Kit Rebuild Kit Operator s Manual Trigger Valve Assembly 23 TROUBLESHOOTING TOOL TROUBLESHOOTING Your pneumatic fastening tool has been designed for long life and trouble free operation However if operating problems arise please use the troubleshooting information below to determine how to remedy the problem N DANGER Always disconnect tool from air supply before performing any service on tool Correcting a problem while the tool is pressurized may result in injury from fastener discharge or tool operation FASTENER DRIVI
6. CE EDGES OR INTO BRITTLE MATERIALS Driving fasteners into extremely hard materials or driving into workpiece edges can cause fasteners to defect away from the workpiece Flying fasteners can cause serious injuries SAFETY SAFETY INSTRUCTIONS 44 KEEP HANDS AND BODY PARTS AWAY FROM AREA Z2 BEING FASTENED Fasteners can defect and turn as they are being driven into the workpiece and penetrate fngers hands and other body parts that may be in the fastening area DO NOT OVERREACH OR WORK WHILE ON UNSTABLE FOOTING If you lose your balance while fastening you could drive a fastener into yourself or a bystander a DO NOT USE TOOL IF TOOL MALFUNCTIONS OR BEGINS 3 LEAKING AIR Operating a malfunctioning tool can result in an unexpected fastener discharge and injury to yourself or others DISCONNECT THE TOOL FROM THE AIR SUPPLY TO 45 RELOAD CLEAR JAMS OR PERFORM MAINTENANCE Never attempt to reload a tool clear a jam or perform maintenance without frst disconnecting the air supply NEVER LEAVE A LOADED PRESSURIZED TOOL UNATTENDED A loaded pressurized tool could be picked up or handled by someone who is unfamiliar with the tool or that has not read the tool manual KEEP TOOLS OUT OF THE REACH OF CHILDREN Place the tool back in the tool box after use and store the tool out of reach DO NOT MODIFY TOOL Modifcations can cause a tool to be unsafe and can cause the tool to operate improperl
7. IST amp SCHEMATIC 16 TROUBLESHOOTING 18 TOOL CHECKS 19 WARRANTY 20 IMPORTANT SAFETY INFORMATION You must read this entire manual and familiarize yourself with all safety operating and service instructions before loading handling or using your tool When used correctly pneumatic fastening tools provide a lightweight powerful and safe means of fastening Used improperly these tools can cause serious injury to you and those around you SPECIFICATIONS GRTFR83 L SPECIFICATIONS MODEL GRTFR83 L FRAMING NAILERS FASTENER RANGE 2 3 1 4 50 mm 83 mm 113 148 dia 3 3 8 mm Round Head FASTENER TYPE 21 Round Head Plastic Collation MAX MAGAZINE CAPACITY 75 Nails MAX AIR PRESSURE 120 psi 8 3 bar MIN AIR PRESSURE 70 psi 4 8 bar TOOL WEIGHT 6 9 Ibs 3 1 kg TOOL LENGTH 21 7 55 1 cm GRTFR83L 22 1 56 1 cm TOOL HEIGHT 12 4 31 5 cm TOOL WIDTH 4 5 11 4 cm TRIGGER TYPE SELECTABLE SEQUENTIAL OR BUMP FIRE AIR INLET MALE SWIVEL QUICK CONNECT COUPLER LUBRICATION 10W Air Tool Oil Provided NOISE CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 3774 ISO 11201 A weighted single event sound pressure level at operator s position LpA 1s 93 dBA A weighted single event sound
8. NG PROBLEMS PROBLEM CORRECTIVE ACTION Fasteners do not drive AT TOOL Turn adjustment dial to increase completely nail drive depth Add 2 3 drops of air tool oil to inlet AT COMPRESSOR Increase air pressure Do not exceed 120 psi 8 3 bar Fasteners do not drive Driver blade worn or broken See dealer for completely after air replacement pressure is increased Fasteners do not drive Inadequate air fow Use larger diameter completely when driv hose Use compressor with larger storage ing in quick succes tank Keep hose lines short Check air hose sion for kinks or other restrictions Fasteners drive too AT TOOL Turn adjustment dial to decrease deeply nail drive depth AT COMPRESSOR Reduce air pressure Do not reduce below 70 psi 4 8 bar 28 TROUBLESHOOTING FASTENER DRIVING PROBLEMS Tool operates but no Check magazine for jammed fastener Clear fastener is driven jam and reload magazine Check nail strip for smooth feeding in magazine Tool won t operate Remove jammed fastener Check magazine nail jammed in tool for incorrect bent or loose fasteners and nose preventing tool discard Reload using Grip Rite nails from operating Tool leaks air Check for source of leak and tighten fttings and screws as required Discontinue using tool if air leaks at trigger area or from cap exhaust Contact your dealer TOOL CHECKS Keep your nailer in top working condition by checking it daily S
9. NSI Z87 1 requirements RISK OF PERSONAL INJURY Failure to follow all safety and operating instructions or misuse of the tool can result in serious injury to tool operator and bystanders SAFETY SAFETY INSTRUCTIONS O e WEAR SAFETY GLASSES Always wear safety glasses with side shields that meet ANSI Z87 1 requirements when operating the tool Make sure all others in work area wear safety glasses WEAR HEARING PROTECTION Wear hearing protection to protect your hearing from noise Prolonged exposure to loud noise can result in hearing loss NEVER OPERATE THE TOOL WITH OXYGEN OR OTHER BOTTLED GASES Oxygen and other reactive or high pressure bottled gases can cause the tool to explode Use clean dry regulated compressed air from a properly operating air compressor DO NOT EXCEED MAXIMUM RECOMMENDED OPERATING AIR PRESSURE OF 120 PSI 8 6 Bar Exceeding the maximum recommended air pressure can cause the tool housing to burst or cause premature failure of components NEVER CONNECT THE TOOL TO AN AIR SUPPLY THAT HAS THE POTENTIAL TO EXCEED 180 PSI 12 4 Bar Using a regulated air supply with a line or tank pressure greater than 180 psi can cause the tool to burst if the air line regulator fails suddenly USE AN AIR HOSE RATED FOR 180 PSI 12 4 Bar OR GREATER Always use air hose rated to handle 180 psi or the maximum potential pressure of the air supply ONLY USE A RELIEVING TYPE AIR COUPLING IN
10. OPERATOR S MANUAL AND PARTS LIST SHORT BODY FRAMING NAILERS MODELS GRTFR83 GRTFR83L GRTFC83 8 GRTFW83 www grip rite com TABLE OF CONTENTS TABLE OF CONTENTS 2 SPECIFICATIONS 3 GRTFR33 L Fastener Selection Chart 3 SAFETY 4 TOOL PART S 8 PART DESCRIPTIONS 9 OPERATION 10 Loading Fasteners 10 Adjusting Nail Drive 11 Selecting Trigger Operation 11 TOOL OPERATION 12 Sequential Operation 12 Contact Trip Operation 12 MAINTENANCE 13 Lubrication 13 Cleaning 13 Trigger Check 13 GRTFR83 PARTS LIST amp SCHEMATIC 14 GRTFR83L PARTS L
11. able pad prevents marring of work Conveniently stores on tool when not needed Metric Hex Wrenches Included with tool to allow tightening of metric screws Keep tools in tool case for periodic tightening of SCrews Air Tool Oil Lightweight oil formulated for use in air tools provides proper lubrication to o rings and internal parts Safety Goggles Provide required eye protection 13 OPERATION LOADING FASTENERS LOADING NAILS N DANGER A fastener can be driven unintentionally if the trigger and safety bracket are activated at the same time Always disconnect tool from air supply before loading fasteners making adjustments or performing any service on tool Keep finger off trigger until ready to drive a fastener 1 Hold tool handgrip securely TOP LOADING GRTFR83 amp GRTFR83L ONLY 2a Insert nail strip into TOP of magazine with nail points angled forward and down Slide nail strip forward REAR LOADING 2B Insert nail strip into REAR of magazine with nail points angled forward and down Slide nail strip forward 3 Pull pusher A back to rear of magazine behind last nail strip 4 Slide pusher forward to engage last nail strip and release 5 Tool is now loaded and ready for normal operation UNLOADING NAILS 1 Pull pusher back fully depress pusher lever B then slide pusher all the way forward to front of magazine 2 Release pusher lever B 3 Slide nail strips back to rea
12. eded Metric Hex Wrenches Included with tool to allow tightening of metric screws Keep tools in tool case for periodic tightening of SCrews Air Tool Oil Lightweight oil formulated for use in air tools provides proper lubrication to o rings and internal parts Safety Goggles Provide required eye protection 13 DESCRIPTION GRTFW83 TOOL PARTS 6 14 DESCRIPTION GRTFW83 PART DESCRIPTIONS 10 Heavy Duty Cap Seals tool housing Cushioned Grip Cushioned handgrip reduces fatigue and provides comfortable operation Rotating Rafter Hook Durable aluminum hook holds tool securely Keeps nailer in reach for greater productivity Swivel Air Coupling Quick disconnect male coupling allows quick connection to air hose and helps improve tool maneuverability Selectable Trigger Permits fingertip selection of single fire or bump fre operation Pusher Release Lever Releases pusher to load or unload nails Spring loaded Pusher Provides positive fastener feeding in all tool positions Dry fire lockout prevents blank firing Work Contact Tip Agressive claw design permits stable positioning for toe nailing in all applications Adjustable Depth of Drive Tool free depth of drive adjustment allows nail drive adjustments to be made at tool for consistent depth control Magnesium Tool Housing Light weight durable magnesium tool housing lowers tool weight reduces operator fatigue No Mar Pad Remove
13. ee your Grip Rite dealer for service if part or operating problems are found Never use a malfunctioning tool it could result in serious injury Workpiece Contact amp Trigger Check workpiece contact for proper operation before each use Workpiece contact must move freely and return to extended position when lifted from workpiece Trigger must operate freely Daily Inspection Check for broken damaged or excessively worn parts and repair or replace as needed Check for air leaks at trigger cap and nose Disconnect tool from air supply immediately if leaks are present and see dealer for service e Make sure all screws are tightened securely 29 WARRANTY PNEUMATIC TOOL COMPRESSOR WARRANTY Pneumatic nailers staplers amp compressors marketed under the GRIP RITE brand are warranted to be free from defects in workmanship amp materials except rubber o rings bumpers seals driver blades dipsticks amp air filters for a period of 3 years for tools and one year for compressors from the date of original purchase This warranty will not apply when The original receipt or copy of the original receipt showing the original purchase date is not provided with tools compressors sent in for warranty repair The tool compressor has been misused abused or improperly maintained Alterations have been made to the original tool compressor Repairs have been attempted made to the original tool compressor by any entity
14. er and then press the workpiece contact against a safe work surface THE TOOL MUST NOT CYCLE 5 With finger off trigger press the workpiece contact against a safe work surface Keep tool pressed against work surface and pull trigger THE TOOL MUST CYCLE ONCE 6 The trigger must return to the normal position each time finger pressure is released 19 GRTFR83 PARTS SCHEMATIC 20 GRTFR83 PARTS LIST ITEM P N DESCRIPTION1 ITEM P N DESCRIPTION45 GRTN7080 Hex Soc Hd Bolt GRTN2530 Spring Pin 2 GRTN6660 Defector 46 GRTN2550 Spring Pin 3 GRTN7060 Hex Soc Hd Bolt 47 GRTN790 Pin Trigger 4A GRTN6670 Cap Assembly 48 GRTN6960 Guide Safety Lever 5 GRTN6680 Gasket 49 GRTN2210 Grommet 6 GRTN220 Washer 50 GRTN7000 O Ring 7 GRTN6710 Spring 51 GRTN6790 Nose 8 GRTN6690 Piston Stopper 52 GRTN2010 Hex Soc Hd Bolt 9 GRTN2420 O Ring 53 GRTN6810 Spring Safety 10 GRTN2160 O Ring 54A GRTN6800 Upper Safety Lever Assy 11 GRTN6700 Piston Head Valve 99 GRIN2660 E ring 12 GRTN7010 O Ring 56 GRTN6840 Adjusting Nut 13 GRTN6620 14 GRTN6610 Piston Head Valve Seal Piston Head 57 GRTN6850 58A GRTN6820 Adjusting Spring Lower Safety Lever Valve Assembly 15 GRTN6630 Retaining Ring 59 GRTN1530 Rubber Pad 16 GRTN2200 O Ring 60 GRTN6600 Door Hinge Pin 17A GRTN6730 Driver A
15. er is to be driven 4 Using a bouncing motion continue moving the tool into position for each fastener drive 5 When fastening is completed release the trigger 18 MAINTENANCE MAINTENANCE Your tool will last longer and perform better if periodic maintenance is performed Please use the information below to keep your tool operating in top condition Lubrication Disconnect tool from the air supply and remove all fasteners Apply 2 3 drops of air tool oil provided in the air inlet two three times a day If the tool will be used outside in the winter use a winter grade air tool oil to help keep frost from forming inside the tool Do not use other types of lubricants on this tool as other lubricants may contain chemicals harmful to o rings and other tool components Drain compressor tanks and hoses daily Cleaning Disconnect tool from the air supply and remove all fasteners Brush tool off using a parts cleaning brush or clean rag Check area around trigger and workpiece contact and clean as necessary Trigger Check Check trigger operation daily to confrm proper sequential operation 1 Move the selector button on the trigger to the rear position 2 Press the workpiece contact against a safe work surface without depressing the trigger THE TOOL MUST NOT CYCLE 3 Hold the tool above a safe work surface and pull the trigger with out depressing the workpiece contact THE TOOL MUST NOT CYCLE 4 Pull and hold the trigg
16. l to help remind you of important safety information when operating the tool The safety label must be legible at all times and must be replaced if it becomes worn or damaged USER MUST READ OPERATION MANUAL BEFORE USING TOOL TO REDUCE THE RISK OF INJURY FAILURE TO GRTFR8 3 FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY ALWAYS WEAR SAFETY GLASSES BEFORE USING THE TOOL NEVER USE BOTTLED OR COMBUSTIBLE GASES OXYGEN ACETYLENE ETC ONLY USE t WARNING REGULATED AIR DISCONNECT AIR SUPPLY WHEN CLEARING A JAM REPLACING NO MAR PAD SERVICING OR WHEN TOOL IS NOT IN USE NEVER CARRY TOOL WITH FINGER ON THE TRIGGER KEEP FINGER OFF TRIGGER WHEN NOT DRIVING FASTENERS AND WHEN LOADING OR UNLOADING NAILS ALWAYS KEEP TOOL POINTED INA SAFE DIRECTION MAX BAR 21 FRAMING NAILER USE 113 148 2 8 3 7mm 2 3 1 4 50 83mm RH NAIL SAFETY SYMBOLS These safety symbols provide a visual reminder of basic safety rules and the personal injury hazard that may arise if all safety and operating instructions are not followed Make sure you understand the meaning of each of these symbols and protect yourself and others by obeying all safety and operating instructions READ THE MANUAL The manual contains important safety and operating instructions that must be followed All tool users must read the manual before using the tool WEAR SAFETY GLASSES Tool operator and bystanders must wear safety glasses with side shield that meet A
17. ool Oil Provided NOISE CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 3774 ISO 11201 A weighted single event sound pressure level at operator s position LpA 1s 93 dBA A weighted single event sound power level LwA 1s 102 dBA A weighted single event surface sound pressure level LpA 1s 89 dBA VIBRATION CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 8862 1 Weighted root mean square acceleration 3 6 m s For best results use Grip Rite collated fasteners GRTFC83 FASTENER SELECTION CHART Size Box Shank Bright Galvanized 2 x 113 Smooth GR03 GR05G GR05HG 2 x 113 Ring GR04 GR04G GRO4HG 2 3 8 x 113 Smooth GR07 GR09G GR09HG 2 3 8 x 113 Ring GRO8R GR08G GRO6RHG 2 3 8 x 148 Smooth GR8D148 GR8D148HG N A 3 x 120 Smooth GR301 GR301G GR301HG 3 x 120 Ring N A GR408G GR408HG 3 x 131 Smooth GR014 N A N A 3 1 4 x 120 Smooth GR444 GR444G GR444HG 3 1 4 x 131 Smooth GR024 GR034G GR034HG 3 1 4 x 148 Smooth GR314148 N A N A SPECIFICATIONS GRTFW83 SPECIFICATIONS MODEL GRTFW83 FRAMING NAILERS FASTENER RANGE 2 3 1 4 50 mm 83 mm 113 148 dia 3 3 8 mm Round Head FASTENER TYPE 21 Round Head Plastic Collation MAX MAGAZINE CAPACITY 75 Nails MAX AIR PRESSURE 120 psi 8 3 bar MIN AIR PRESSURE 70 psi 4 8 bar TOOL WEIGHT 6
18. power level LwA 1s 102 dBA A weighted single event surface sound pressure level LpA 1s 89 dBA VIBRATION CHARACTERISTIC VALUES IN ACCORDANCE WITH ISO 8862 1 Weighted root mean square acceleration 3 6 m s For best results use Grip Rite collated fasteners GRTFR83 L FASTENER SELECTION CHART Size Box Shank Bright Galvanized 2 x 113 Smooth GR03 GR05G GR05HG 2 x 113 Ring GR04 GR04G GRO4HG 2 3 8 x 113 Smooth GR07 GR09G GR09HG 2 3 8 x 113 Ring GRO8R GR08G GRO6RHG 2 3 8 x 148 Smooth GR8D148 GR8D148HG N A 3 x 120 Smooth GR301 GR301G GR301HG 3 x 120 Ring N A GR408G GR408HG 3 x 131 Smooth GR014 N A N A 3 1 4 x 120 Smooth GR444 GR444G GR444HG 3 1 4 x 131 Smooth GR024 GR034G GR034HG 3 1 4 x 148 Smooth GR314148 N A N A SPECIFICATIONS GRTFC83 SPECIFICATIONS MODEL GRTFC83 FRAMING NAILERS FASTENER RANGE 2 3 1 4 50 mm 83 mm 113 148 dia 3 3 8 mm Round Head FASTENER TYPE 30 34 Clipped Head 8 Offset Round Head Paper Collation MAX MAGAZINE CAPACITY 95 Nails MAX AIR PRESSURE 120 psi 8 3 bar MIN AIR PRESSURE 70 psi 4 8 bar TOOL WEIGHT 7 6 lbs 3 4 kg TOOL LENGTH 21 3 55 1 cm TOOL HEIGHT 13 8 31 5 cm TOOL WIDTH 4 5 11 4 cm TRIGGER TYPE SELECTABLE SEQUENTIAL OR BUMP FIRE AIR INLET MALE SWIVEL QUICK CONNECT COUPLER LUBRICATION 10W Air T
19. r of magazine depress the stopper C and remove the nails from rear loading slot 16 OPERATION ADJUSTING NAIL DRIVE 1 Disconnect tool from air supply using quick connect coupling 2 Turn adjustment dial D backward toward magazine to increase nail drive or forward toward front of tool to decrease nail drive as shown by nail symbols on tool 3 Connect tool to air supply and NAIL TOO DEEP drive nails to check for correct a depth of drive BACKWARD FORWARD 4 Make depth of drive adjustments as needed to maintain consistent nail driving SELECTING TRIGGER OPERATION 1 Disconnect tool from air supply using quick connect coupling BUMP FIRE OPERATION 2a Slide the selector button E on the trigger to the forward position SEQUENTIAL FIRE OPERATION 2b Slide the selector button E on the trigger to the rear position 3 Connect air tool to air supply at quick connect coupling 17 OPERATION TOOL OPERATION SEQUENTIAL SINGLE FIRE OPERATION To operate this tool in SEQUENTIAL fire mode move the selector button on the trigger to the rear position 1 Hold the tool securely using the handgrip Keep finger off trigger until tool is in position and you are ready to drive a fastener NOTE Depressing trigger before depressing safety bracket will prevent tool from actuating 2 Position the nose of the tool on the workpiece placing the nose at the desired fastener driving po
20. sition 3 Press the tool down firmly against the work surface fully depressing the workpiece contact safety bracket 4 Squeeze the trigger once to drive a fastener 5 Allow the tool to rebound off the work surface and release the trigger to reset the workpiece contact Tool will not drive another fastener until trigger is released and cannot be bump fred with sequential operation mode selected 6 Check fastener for flush drive and if needed turn nail depth adjustment dial to obtain desired fastener drive 7 If tool adjustments do not provide the desired results make air pressure adjustments at the compressor Increase air pressure to drive deeper or to drive into harder materials Reduce air pressure to reduce drive or to drive into softer materials For longest tool and part life always use the lowest air pressure necessary to drive fasteners to desired depth 8 Position the tool for driving the next fastener and repeat the above procedure Always keep hands and other body parts away from areas being fastened BUMP FIRE CONTACT TRIP OPERATION To operate this tool in BUMP FIRE mode contact trip move the selector button on the trigger to the forward position 1 Position the nose of the tool over the work surface near the area where the frst fastener is to be driven 2 Squeeze and hold the trigger in the depressed position 3 Bump the workpiece contact safety against the work surface at each point where a fasten
21. ssembly 61 GRTN6640 Spiral Spring 18 GRTN2460 O Ring 62 GRTN6890 Roller 19 GRTN250 Cylinder Hold Down 63 GRTN7070 Pin 20 GRTN240 Seal 64 GRTN6900 Pusher 21 GRTN2430 O Ring 65 GRTN6940 Safety Lock Out 22 GRTN6720 Cylinder 66 GRTN6910 Carriage 23 GRTN2190 O Ring 67 GRTN2210 Grommet 24 GRTN6740 Bumper 68 GRTN6650 Spring 25A GRTN6750 Body Assembly 69 GRTN7040 Hex Soc Hd Bolt 26 GRTN4430 O Ring 70 GRTN6870 Nail Guide Liner 27 GRTN6760 End Cap 71 GRTN6880 Nail Guide Liner 28 GRTN6770 Belt hook 72 GRTN7050 Hex Soc Hd Bolt 29 GRTN6990 O Ring 73 GRTN6930 Stopper 30 GRTN6970 31 GRTN4180 Washer Belt Hook Cover Belt hook 74A GRTN6860 75 GRTN6950 76 GRTN7020 Magazine Assembly Magazine Cover Flat Washer 32 GRTN4190 C ring 33 GRTN2220 O Ring 77 GRTN2710 Cap Locknut 34 GRTN800 Valve 78 GRTN6070 Hex Soc Hd Bolt 35 GRTN2240 O Ring 79 GRTN6920 Bracket 36 GRTN2100 O Ring 80 GRTN6050 Flat Washer 37 GRTN6250 O Ring 81 GRTN3340 Locknut 38 GRTN805 Valve Plunger 82 GRTN4020 Hex Soc Hd Bolt 39 GRTN2170 O Ring 83 GRTN6050 Flat Washer 40 GRTN830 Spring 84 GRTN7090 Hex Soc Hd Bolt 41 GRTN2230 O Ring 85 GRTN7030 Flat Washer 42 GRTN810 Plunger 86 GRTN7040 Hex Soc Hd Bolt 43 GRTN820 Plunger Cap 87 GRTN6830 Safety Cap 44A GRTN6780 Trigger Assembly 88 GRTN7130 Flat Washer A GRDAK2300 Driver Assembly Kit B GRRBK2300 Rebuild Kit C GRTFR83MAN Operator s Manual D GRTRK100 Trigger Valve Assembly 21 GRTFR83L PARTS SCHEMATIC
22. tric screws Keep tools in tool case for periodic tightening of screws Air Tool Oil Lightweight oil formulated for use in air tools provides proper lubrication to o rings and internal parts Safety Goggles Provide required eye protection 11 DESCRIPTION GRTFC83 TOOL PARTS 6 12 DESCRIPTION GRTFC83 PART DESCRIPTIONS 10 Heavy Duty Cap Seals tool housing Cushioned Grip Cushioned handgrip reduces fatigue and provides comfortable operation Rotating Rafter Hook Durable aluminum hook holds tool securely Keeps nailer in reach for greater productivity Swivel Air Coupling Quick disconnect male coupling allows quick connection to air hose and helps improve tool maneuverability Selectable Trigger Permits fingertip selection of single fire or bump fre operation Pusher Release Lever Releases pusher to load or unload nails Spring loaded Pusher Provides positive fastener feeding in all tool positions Dry fire lockout prevents blank firing Work Contact Tip Agressive claw design permits stable positioning for toe nailing in all applications Adjustable Depth of Drive Tool free depth of drive adjustment allows nail drive adjustments to be made at tool for consistent depth control Magnesium Tool Housing Light weight durable magnesium tool housing lowers tool weight reduces operator fatigue No Mar Pad Removeable pad prevents marring of work Conveniently stores on tool when not ne
23. w grip rite com where you will find a list of our authorized service centers Contact the GRIP RITE Factory Warranty Center directly at Phone 800 207 9259 or Fax 800 207 9614 n Canada Call 866 512 1418 STEPS TO TAKE WHEN SHIPPING TOOLS Adequately package the product to avoid damage in transit in the case of pneumatic tools the original blow mold plastic carrying case is considered adequate packaging Provide the original copy of receipt showing the original purchase date Insure your shipment with the shipping company PRIMESOURCE will not be responsible for any tool compressor that is lost or damaged by the shipper on route to the PRIMESOURCE service warranty center 31 USE GENUINE GRIP RITE FASTENERS FOR BEST PERFORMANCE www grip rite com Distributed by Distribuido por Imported by Import par PRIMESOURCE BUILDING PRODUCTS INC an BUILDING PRODUCTS CANADA CORPORATION are Itochu Companies Irving Texas 75038 USA www primesourcebp com GRTF83MAN 8 10
24. y DESCRIPTION GRTFR83 L TOOL PARTS 6 10 DESCRIPTION GRTFR83 L PART DESCRIPTIONS 1 Heavy Duty Cap Seals tool housing 2 Cushioned Grip Cushioned handgrip reduces fatigue and provides comfortable operation 3 Rotating Rafter Hook Durable aluminum hook holds tool securely Keeps nailer in reach for greater productivity 4 Swivel Air Coupling Quick disconnect male coupling allows quick connection to air hose and helps improve tool maneuverability 5 Dual Loading Magazine Allows fast easy top or rear loading of nails Open track design permits quick check of nail size and quantity 6 Selectable Trigger Permits fingertip selection of single fire or bump fre operation 7 Pusher Release Lever Releases pusher to load or unload nails 8 Spring loaded Pusher Provides positive fastener feeding in all tool positions Dry fire lockout prevents blank firing 9 Work Contact Tip Agressive claw design permits stable positioning for toe nailing in all applications 10 Adjustable Depth of Drive Tool free depth of drive adjustment allows nail drive adjustments to be made at tool for consistent depth control 11 Magnesium Tool Housing Light weight durable magnesium tool housing lowers tool weight reduces operator fatigue No Mar Pad Removeable pad prevents marring of work Conveniently stores on tool when not needed Metric Hex Wrenches Included with tool to allow tightening of me
Download Pdf Manuals
Related Search