Lock-Top 09115 Installation Guide
Contents
1. link in the bag also Remove dome nut from the end of connecting tube and assemble chimney fire safety device as shown at right The chimney fire safety device must be installed for the warranty to be in effect Black tube Leg connector wire with fusible link damper lid Position safety device wire corner to cor ner and re tighten dome nut onto end of bolt Turn jam nut an additional 1 4 turn with wrench to secure Chimney fire safety device Spread 1 4 bead of furnished adhesive around top of chimney opening Insert cable and handle down chimney making sure they extend into fireplace Center damper on top of chimney and press down firmly on frame Fill any gaps with adhesive to ensure a prop er seal Allow adhesive to set 24 hours before using damper If using a Sweep s Ring sold separately apply the ring to the adhesive and screw damper to ring Bracket installation Drill 1 4 hole in firebrick toward front of fireplace approximately 20 off firebox floor Insert nail anchor through top hole of bracket and into hole in brick Fasten Be sure bracket is straight and then use second hole in bracket as guide to drill a second hole in brick Fasten with second anchor nail Thread handle chain and cable through bracket hole until all slack is out of cable Loosen brass adjustment clamp with Allen wrench and slide it up cable to bracket Pull the cable to close damper and adjust clamp position for the tightes2. Lock Top Energy Saving Fireplace Damper with Chimney Fire Safety Device Installation Instructions To install the Lock Top Damper you will need these tools drill hammer wire pliers 1 4 masonry bit 1 2 open end or adjustable wrench Dome nut Safety device wire positioned corner to corner Bracket Leg connector Adjustment wire with clamp fusible link 2004 Gelco Lyemance Lock Top l N wo 5 Insert threaded end of conduit tube into underside of Find the safety device wire located under the damper lid Find the spring loaded connecting tube with jam nut cable and handle in the hardware bag Find the leg connector wire with fusible link in the bag also Remove dome nut from the end of connecting tube and assemble chimney fire safety device as shown at right The chimney fire safety device must be installed for the warranty to be in effect Black tube Leg connector wire with fusible link damper lid Position safety device wire corner to cor ner and re tighten dome nut onto end of bolt Turn jam nut an additional 1 4 turn with wrench to secure Chimney fire safety device Spread 1 4 bead of furnished adhesive around top of chimney opening Insert cable and handle down chimney making sure they extend into fireplace Center damper on top of chimney and press down firmly on frame Fill any gaps with adhesive to ensure a prop er seal Allow adhesive to set 24 hours before
3. t seal Tighten screw in clamp with Allen wrench Cut and discard excess cable
4. using damper If using a Sweep s Ring sold separately apply the ring to the adhesive and screw damper to ring Bracket installation Drill 1 4 hole in firebrick toward front of fireplace approximately 20 off firebox floor Insert nail anchor through top hole of bracket and into hole in brick Fasten Be sure bracket is straight and then use second hole in bracket as guide to drill a second hole in brick Fasten with second anchor nail Thread handle chain and cable through bracket hole until all slack is out of cable Loosen brass adjustment clamp with Allen wrench and slide it up cable to bracket Pull the cable to close damper and adjust clamp position for the tightest seal Tighten screw in clamp with Allen wrench Cut and discard excess cable Lock Top Energy Saving Fireplace Damper with Chimney Fire Safety Device Installation Instructions To install the Lock Top Damper you will need these tools drill hammer wire pliers 1 4 masonry bit 1 2 open end or adjustable wrench Dome nut Safety device wire positioned corner to corner Bracket Leg connector Adjustment wire with clamp fusible link 2004 Gelco Lyemance Lock Top 1 N wo 5 Insert threaded end of conduit tube into underside of Find the safety device wire located under the damper lid Find the spring loaded connecting tube with jam nut cable and handle in the hardware bag Find the leg connector wire with fusible
Download Pdf Manuals
Related Search