MaxxAir HVP F30 UPS Use and Care Manual
Contents
1. unit you must select one of the following methods A Return to factory Return postage prepaid only the part or component which you believe to be defective to the following address Ventamatic Ltd 100 Washington Street Mineral Wells TX 76067 Complete and enclose a written claim and attach a copy of your sales slip or other proof of purchase B Return to retail dealer There is no informal dispute settling mechanism available in the event of a controversy involving this warranty Any and all implied warranties which may exist terminate upon the expiration of this warranty one 1 year from the date of the original retail purchase Some states do not allow limitations on how long an implied warranty lasts so this limitation may not apply to you Ventamatic Ltd is not liable to you for incidental or consequential damages arising out of a defect or malfunction of a unit or its installation or out of any alleged breach of this warranty Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which may vary from state to state you many years of use Please read the safety 30 INCH PEDESTAL FAN OPERATING INSTRUCTIONS MODEL HVPF 30 CONGRATULATIONS ON YOUR PURCHASE OF THE MaxxAir 30 INCH HIGH VELOCITY PEDESTAL FAN With proper care and maintenance the fan wil2. VYentamatic Ltd LIMITED WARRANTY N AIR OF EXCELLENCE Ventamatic Ltd extends this warranty to the original retail purchaser of this fan The fan is warranted against defects in materials and workmanship for a period of two 2 years from the date of original retail purchase No other parts or components are warranted There is no warranty for defects caused by abuse Repairs or replacement parts supplied under this warranty are warranted only for the period of this warranty that is two 2 years from the date of the original retail purchase of the unit In the event of a defect or malfunction we will replace or repair the defective part or component only and return the new or repaired part to you freight prepaid You must bear all other expenses incurred in obtaining repairs including labor required for field repair or replacement and the cost of shipping the defective part to us You must also bear the cost of repair to or replacement of any part or component and the shipping charges incurred for the repair or replacement and return to you of any part or component not covered by this warranty including parts or components damaged by you The company reserves the right to demand and receive written evidence of the date of purchase before undertaking to perform its obligations under this warranty You should therefore retain your sales slip and attach a copy of it to the warranty claim In order to obtain the repair or replacement of this
3. high medium or low CLEANING WARNING Unplug from electrical supply source before cleaning After servicing any safety device including grilles and blades must be reinstalled or remounted as previously installed To clean use a soft damp cloth then wipe dry with a dry cloth Do not use harmful cleaners Do not bend blades FAN COMPONENTS 17 16 15 14 13 1 Base frame 2 Coupler 3 Five 5 screws flat and spring washers 4 Coupler cover 5 Stand assembly with spring 6 Two 2 screws and washers 7 Adjuster 8 Adjustment knob Ks 9 Extension pipe assembly 10 Pivot knob and square neck bolt 11 Position bolt spring washer and nut 12 Motor assembly 13 Four 4 screws flat and spring washers 14 Allen wrench 15 Rear grille 16 Blade assembly 17 Front grille 18 Small bolt spring washer i and nut for grille not shown ot a POSITION BOLT 2 SPRING WASHER amp NUT
4. hole in motor flange on motor assembly 12 3 Insert bolt and replace flat washer spring washer and nut 11 removed in Step 1 4 Adjust tilt to desired position insert square bolt two flat washers and pivot knob 10 and tighten pivot knob 10 to set the angle 5 Tighten position bolt and nut 11 REAR GRILLE amp BLASE ASSEMBLY 1 Remove four screws spring washers and flat washers 13 from motor around motor shaft 2 Align the rear grille 15 over the threaded holes in the motor Align the rear grille so that the one small hole in the outer ring is located to your lower right when facing the fan Secure with flat washers spring washers and screws 13 removed in Step 1 Carefully slide blade assembly 16 over shaft and align inner Allen head screw with slot on motor shaft Tighten blade assembly 16 CAUTION Do not alter angle of blades nm A Ww FRONT GRILLE ASSEMBLY 1 Open clips in front of grille 2 Hang front grille 17 on top rib of rear grille 15 by utilizing the U shaped fixed clip at top of front 3 Insert and secure safety grille bolt spring washer and nut 18 4 Press clips down around front grille to secure OPERATION INSTRUCTIONS To Adjust Airflow Upward or Downward Loosen position bolt 11 then loosen pivot knob 10 Tilt motor to desired angle and firmly tighten pivot knob 10 Firmly tighten pivot bolt 11 Speed Control Pull chain on motor assembly to set desired setting
5. l afford HY OLY iV III GA y instructions and save for future reference CAUTION Read and follow all instructions before operating fan Do not use fan if any part is damaged or missing Warning To reduce risk of fire or electrical shock do not use this fan with any solid state speed control device This appliance has a 3 prong plug To reduce the risk of electrical shock this plug is intended to fit in an outlet only one way If this plug does not fit the outlet contact a qualified electrician RULES FOR SAFE OPERATION Do not insert fingers or any objects through grille guard when fan is in operation e Disconnect fan when moving from one location to another e Disconnect fan when removing guards for cleaning e Make sure fan is on a stable flat surface when in operation e Rain and moisture may create an electrical hazard e In order to prevent extension pipe spring from projecting up do not release two adjustment screws 6 when pipe is all the way down VENTAMATIC LTD P 0 BOX 728 MINERAL WELLS TX 76068 0728 PHONE 800 433 1626 FAX 940 325 9311 WWW BVC COM E MAIL BVC BVC COM Aleader in the ventilation industry for over 60 years Ventamatic Ltd offers a complete line of air movement Se Wer products for commercial industrial agricultural and residential use sold under these fine names Ventamatic nuVent 2010Ventamatic Ltd HVPF30 OPERINSTR UNPACK YOUR FAN AND CHECK THE CONTENTS number
6. s below refer to diagram at right e Motor Assembly 10 11 12 Base Frame Assembly 1 3 Stand Assembly amp Spring 2 5 6 7 8 Extension Pipe Assembly 9 Rear Front Grille amp Blade 13 14 15 16 17 18 Coupler Cover 4 Box with Owner s Manual Coupler Cover 4 Base screw package 3 Pivot knob and square neck bolt 10 Adjustment knob 8 Position bolt spring washer amp nut 11 and Grille safety bolt spring washer and nut 18 not shown STAND AND BASE ASSEMBLY 1 Put stand assembly with spring 5 on base frame 1 and align holes in the coupler 2 with holes in base frame 1 2 Insert screws and spring washers 3 and tighten securely 3 Slide coupler cover 4 down over the coupler STAND ASSEMBLY 1 Make sure spring is in stand assembly 5 2 Remove two screws 6 from adjuster 7 of extension pipe 9 and insert the adjustment knob 8 and loosely tighten the adjuster 7 3 Insert pipe extension 9 into stand pipe 5 4 Align two holes on stand pipe 5 with holes on adjuster 7 secure adjuster 7 with two screws 6 removed in Step 2 5 Adjust extension pipe 9 to desired height 6 Tighten adjustment knob 8 to set the height STAND MOTOR ASSEMBLY 1 Remove bolt flat washer spring washer nut for motor position 11 and square bolt pivot knob for angle setting 10 from coupler cover package 2 Align upper round hole on extension pipe assembly 9 with upper round
Download Pdf Manuals
Related Search