Pridiom AMS180HR Use and Care Manual
Contents
1. A G f Fuse offen N 5 breaks off iy H d r Naum Malfunction is observed TV radio or other devices Ze When faulty operation movement is observed when the RUN button is pressed restarting the operation after 3 minutes faulty movement does not disappear agin a 3Minute i goby but why d a eS The unit can not be restarted just after shut down RUN lamp is illuminating A P wen s We hope you will know the following when using the unit Restart is stopped for 3 minutes after shut down to protect the unit an KANE ei TS er Please wait for 1 3 minutes be JA e K Three minute protection timer incorporated in the microcomputer actuates automatically Except that power is connected this function does not actuate Air is not blown out at starting of heating operation The unit will not stop blowing out the air immediately after shut down at COOL operation Air is not blown out for 6 to 12 min at heating operation Air is not blown out at DRY operation Air blow is stopped to prevent blowing out of cold air until the indoor heat exchanger is warmed 2 to 5 min HOT KEEP Because the unit is doing mould proofing operation and indoor fan motor runs at low speed The louver will not close down until after 30 seconds When outdoor temperature is low and humidity is high the unit sometimes performs defrosting automatic2. AWOSo9OHR 120HR 180HR 240HR AWSogoHR AWS120HR AWS180HR AWS240HR HIGH WALL SPLIT AIR CONDITIONER a AOS120HR User manual www Pridiom com Air conditioners are units that should have the professional technicians do the installation for you This Instruction Manual is the universal purpose version for the models of split wall mounted air conditioners manufactured by our Co The appearance of the units that you purchase might be slightly different from the ones described in the Manual but it does not affect your proper operations and usage Please read carefully the sections corresponding to the specific model you choose and keep the Manual properly so as to facilitate your reference at later time Addition to the user manual The appliance is not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance CONTENTS Instructions to users The name of each part and its function Operation and indication sections of remote controller Use of remote controller Features of heating operations Methods of maintenance Treatment at service call We hope you will know the following when using the unit O OO NGO OW gt Instructions to users Please read the Instruction Manual carefully prior to the use of your air conditioner so as to ensure proper operations Instructions for Installation Make
3. 90 F It would be automatically set at 25 C 76 F and unadjustable in AUTO and DYR mode 3 Press the FAN SPEED button to choose the air rate you want Low display indicates Med display indicates al Widisplay indicates 444 Auto display lt ll indicator flashing It would be automatically set at low speed and unadjustable in DRY mode 4 Press the SWING button to choose the up down air flow direction you want natural flow display indicates nfn upu i v It would be automatically set at fixed wind air flow direction in DRY mode TURBO OPERATION Press TURBO button during COOL or HEAT operation the air rate can be setted in HIGH Press the TURBO button again can release the TURBO operation Note during TURBO operation the air rate cann t be changed ADJUSTING LEFT RIGHT AIR FLOW DIRECTION Methods 1 Manually adjust Adjust the direction by moving directly the left right air flow direction adjusting fin by hand Caution when adjust the direction stop air conditioner Methods 2 Horizontal amp vertical auto swing three dimensional air flow model Adjust the direction by remote controller Press the AIR FLOW button the air swinging fins will constantly make the left right swinging or fixed direction in air delivery TIMER OPERATION Set turning off time Set the time for the unit to turn off and when it is time the air conditioner will automatically stop operating 1 During the operation of the air condition
4. LLC 80 Broadway Cresskill NJ 07626 201 266 8232
5. or place any other objects on it Hot water gew 40 C or 104 F The use of hot water will deform the air conditioner or make it fade in color Gasoline paint diluent benzene and polishing agents etc These substances will deform the air conditioner or cause scratches The falling down of the unit or the objects might cause human injuries and other accidents Instructions for Removal and Repair Do not use combusting apparatuses in the air conditioned room It might lead to the incomplete combustion of these apparatuses Prior to the maintenance of the air conditioner please cut off the power supply first Never do the cleaning of the units when the fan is in high speed operations It might cause discomforts of the body which is harmful to your health Check the supporting structures of the units carefully In case of damages the supporting structures should be immediately repaired so as to avoid falling down of the unit which might cause human injuries or other accidents Put down the power when the unit is not in use for long time so as to ensure safety When the plug is to be pulled out make sure that the switch of the air conditioner is turned off When removal or repair is needed please contact the dealer or authorized maintenance amp installation people In case of any abnormal occurrences smell of burning please stop the operation at once cut off the power supply and contact the
6. sure to have the professional after sale service persons of our company or the authorized dealers to install the units before you use 1 The units are not to be installed at places where Make sure that the earth leakage circuit breaker there might be leakage of combustible gases is installed O Earth leakage circuit breaker In case that the leaked gas accumulates around the units there Absence of the earth leakage circuit breaker might lead to electric might occur the accident of fire hazards shock and some other hazards After the connecting of the wires between the indoor unit and the Make sure that the air conditioner is properly grounded outdoor unit check whether the connecting is loose or not by pulling the wire with a little force The grounding wire on the air conditioner should be tightly connected to the ground of the power source Improper grounding might cause The loose connecting might result in fire hazard ay electric shocks or other hazards Instructions for Operation Never try to stop the operation of the air conditioner by operate the switch At Do not press stretch damage heat or modify the power line It might cause electric shocks overheating fire hazards etc If the power line wire is damaged or needs to be replaced due to some other reasons please make sure to have dealer or the authorized maintenance people to do the replacement Such performance might cause electr
7. R FLOW button optional This button used for selection of the left right LAMP air flow direction whenever pressed the in flap will swing or fix It just works on three dimensional air flow model SLEEP button TIMER button This button changes to SLEEP operation This button is used to set the switch on or HOLD button switch off and the timer time Press this button to lock or unlock the keyboard NOTE Above figure shows all indications for the purpose of explanation but practically only the pertinent parts are indicated When air conditioner is cooling only model the HEATis for FAN When TURBO operation is selected room temperature is not controlled with operation being continually If you feel the room temperature is too cool or too heat please cancel the TURBO operation Transmission procedure When each button on the remote controller is pressed with the remote controller pointing toward the air conditioner unit signal is sent When the signal is received correctly the receiving sound is emitted from the unit Use of remote controller OPERATING MACHINE IN SELECTED MODES 1 Point the remote controller at the unit oress the ON OFF button then press the MODE button select the needed mode ATUO COOL DRY HEAT or FAN 2 Press the SET TEMPERATURE button to increase or decrease the readings until the needed temperaure is displayed The room set temperature range is from 16 C 32 C 61 F
8. ally Please wait During defrosting water or steam are raising from the outdoor unit Indoor fan is sometimes stopped to prevent vapor of dehumidified moisture and save energy Mist is blown out at COOL operation This phenomenon sometimes occurs when the temperature and humidity of the room are very high but it will disappear with the lowering of the temperature and humidity Odor is sent out Noise is heard cracking sound Air blown out during operation may smell This is the smell of tobacco or cosmetics sticked to the unit This is caused by the refrigerant that is circulating inside the unit Noise is heard cracking sound After a power stoppage or after disconnecting the power supply plug This is caused by heat expansion or contraction of plastics Operation can not be restarted even if the power is recovered Remote control signals are not received Moisture may form on the air outlet grilles The memory circuit of the microcomputer is cleared Operate the remote controller again to restart the operation Remote control signals may not be received when signal receiver on the air conditioner body is exposed to direct sunlight or strong lighting In that case interrupt the sunlight or darken the lighting If the unit is operated for a long period of time with the high humidity moisture may form on the air outlet grilles and drip down 10 PRIDICOM Pridiom Group
9. dealer or authorized maintenance people I m The name of each part and its function gt Operational performance indications Air return grid Takes in the indoor air SSS Removes dust or dirt out of the inlet air Lelf right air flow direction adjusting fin Up down air flow direction adjusting flap N N N N N A N N N N N N Air blows out from here Drain tube A Drain the water dehumidifird out of the air Refrigerant piping connection rae Air discharge vent IZ How to close Push down the air inlet grid and the push both sides of air How to open inlet grid at the bottom Emergency operation key Lightly push both sides of the air inlet grid at the This button can be used as an emergency measure to turn on off unit bottom and pull it to this side till a resistance is felt when remote controller is not available Note Do not open the grid at an angle over 60 degrees Do not operate the units with too much force ii Heating indicator Flap SWINGING Dehumidifing Cooling cooling and Auto model Sleeping Timer time indicator indicator indicator heating model indicator indicator indicator Indoor fan motor running display Setting temperature and Fan speed indicator malfunction code indicator Above figure shows all indications for the pur
10. er press the TIMER button and the air conditioner will enter the timed switch off mode swing display indicator flashing fixed wind display indicates i kd 2 Continuely press the TIMER button to set the needed time for switching off the machine The timer can make the setting in the range from 1 24 hours Every the button is pressed indication change is the following sequence VP Si ek ees gt 24 gt cancel no indication 1 3 After the setting of the timed switch off the digits shown on the display screen will go down by 1 for every elapsed hour The displayed digits indicate the remaining time prior to the timed switch off Set turning on time Set the time for the unit to turn on and when it is time the air conditioner will automatically start operating 1 When the air conditioner is in the standby mode press the TIMER button and the air conditioner will enter the timed switch on mode 2 Continuely press the TIMER button to set the needed time for switching on the machine The timer can make the setting in the range from 1 24 hours Every the button is pressed indication change is the following sequence E aaa gt 24 gt cancel no indication gt 1 3 After the setting of the timed switch on the digits shown on the display screen will go down by 1 for every elapsed hour The displayed digits indicate the remaining time prior to the timed switch on SS 6 Releasing procedure When the indication on disp
11. ic shocks or fire hazards Do not operate the switch by wet hands Never use the fuse with incorrect capacity or any other metal wires WER Ti N copper wire The use of metal or copper wires for fuse might cause operational It might cause electric shocks failures or fire hazards Try to minimize the generation of heat during the operation of cooling Try to avoid the sunlight and hot air from entering the room I m scorched During the cooling operation curtains or window blinds should be used to shade off the sunlight Place the heating sources out of the room When it is necessary to use the air conditioner and the combusting apparatuses in the same room air ventilation has to be made from time to Do not place insecticides or paints and other flammable sprays near the air conditioner or spray them directly at the air conditioner le Insufficient ventilation might lead to lack of oxygen or some other dangers As the fan is in high speed operation the insertion Properly adjust the up down and left right directions might lead to accidents of the air flow so as to get the even room temperature Do not attach hang or stack articles on the air conditione Do not clean the air conditioner with water It might lead to the falling down of the air conditioner It might cause electric shocks unit which will result in accidents or injuries Do not sit on the outdoor unit
12. lay screen is 24 hour press the TIMER button again to delete the timed mode SLEEP OPERATION Use this mode to reduce operation sound when sleeping etc Press the SLEEP button the air flow sound from the indoor unit is decreased Press the SLEEP button again can release the mode NOTE e Use the sleep mode when you are going to bed H this mode is used in the day the capacity is reduced since the ambient temperature is too high COOL MODE e During the operation of cooling the room temperature will be raised gradually by 2 C 4 F higher than the setting after the machine begins to operate in the sleeping mode e During the operation of heating mode the room temperature will be dropped gradually 5 C 9 F lower than the setting after the machine begins to operate in the sleeping mode REPLACEMENT OF BATTERIES e When the signal from the remote controller becomes weak and the indoor unit can not receive it properly or the indications on the display screen becomes blurred please slide the back cover and replace with two new batteries Remote Controller 1 e The positive and negative poles must match the installation positions e New batteries of the same type have to be used for replacement t apes not wanan anis medal e f the remote controller is not to be used for long time take out the H RST button batteries so as to prevent the leakage of the electrolyte from damaging
13. n is resumed eS Methods of Maintenance The air conditioner must be turned off power before the maintenance is to be carried out Before the season of operation Check if there are any blocking materials in the intake and outlet vents of the indoor and outdoor units 2 Check if the installation stand is corroded or rusty Check if the machine is properly grounded r 4 Check if the air filter is clean 5 Connect to the power source 6 Put batteries in the remote controller After the season of operation d Set the temperature at 20 C or 86 F and operate in the fan status for about half a day To make the interior of the units dry 2 Stop the operation of the machine and turn off the power switch IL 7 The air conditioner will consume about SW of electric power after the machine is turned off For the purpose of energy saving and safety it is advisable to pull the plug out during the non operational seasons 3 Clean and install the air filter screen Ee bw During the season of operation The cleaning of the air filter screen Standard intervals should be once every two weeks d Remove the air filter screen from the unit e Gently press the two lower ends of the grid and open it e Gently pull up the air filter screen and take it out in the direction of your body if the screen is very dirty please use lukewarm water about 30 C or 86 F to clean it Air it dry after
14. pose of the explanation but practically only the partinent parts are indicated The indicator may be changed but it does not affect your operation Operation and indication sections of remote controller This remote controller is the general one used for many types of air conditioner in our company we beg your forgiveness that we would not introduce the button or indicator which is not applicable for units you purchased The LAMP button is applicable for special latest developed new models only instead of normal models Temperature indicator Indicates the set temperature AUTO indicator COOLING indicator DRYING indicator HEATING indicator FANING indicator SLEEP indicator Indicates during sleep operation TURBO indicator Indicates during TURBO operation L Key lock indicator SWING indicator Indicates selected flap mode TIME indicator Indicates timer time SET TEMPERATURE button This button sets the room temperature MODE button This button changes the operation mode AUTO COOL DRY HEAT FAN FAN SPEED button This button set air rate TURBO button This button changes to TURBO operation It does not work in AUTO DRY and FAN mode FAN SPEED indicator Indicates the seted air rate ON OFF button This button when pressed starts operation and stops when repressed SWING button This button changes the flap mode natural flow swing or fixed wind MODE swine AIRFLOW SLEEP AI
15. push the RST button with the tip of a the controller ale GE elt when the remote controller is at abnormal state you can take out the batteries on the back cover to clear off the display ees Features of Heating Operations L J Remote Controller 2 Basic principles and performances The machines absorb heat from the outdoor air and transfer it indoors so as to heat the room air The heating capabilities through this principle of heat pump go up down with the increase decrease of the temperatures of the outdoor air It only needs a fairly short time for such hot air circulation system to raise the room temperature When the outdoor air temperature is very low the system can be used together with other heating devices But good ventilation should be maintained to ensure safety and prevent accidents Defrosting When the outdoor air temperature is very low and humidity is very high frosting will occur to the heat exchanger of the outdoor unit which has negative impacts upon the efficiency of the heating performance In such case the automatic defrosting function will come into play The heating operation will be stopped for 5 10 minutes to do the defrosting The fans of both the outdoor and indoor units are stopped During the defrosting the outdoor unit might generate some steam It is caused by fast defrosting which is not a performance failure Upon the completion of the defrosting process the heating operatio
16. the cleaning Note Do not use boiling water to clean the screen Do not bake the screen dry over a fire Do not exert too much force in pulling and stretching the screen Install the air filter screen To operate the air conditioner without the air filter screen on will cause the interior of the machine dirty which might lead to poor performances or damages to the units Clean the air conditioner Use a soft and dry cloth to rub the air conditioner or use a vacuum cleaner to clean it 6 If the air conditioner is very dirty use a piece of cloth and soak it with neutral home use detergent to do the cleaning Note If the air filter screen is blocked by dust or dirt the performance of cooling and heating will be affected with the operation noise and power consumption increased Therefore the air filter screen should be cleaned regularly Treatment at service call Please check the following before requesting after sale service from your dealer fe The air conditioner does not operate at all Is the time set to ON position Is there a power failure or a blown 7 Is the room temperature setting suitable suitable TEMP Is direct sunlight entering the room in the room AE in me room h 4 ST E D FEL z A A A NG an A TEE a PIA wi Fuse or breaker often breaks off Abnormal noise is heard during operation wd Ba
Download Pdf Manuals
Related Search