Concepts In Wood MI4836-E Instructions / Assembly
Contents
1. PG 1 ASSEMBLY MANUAL p Bookcase Re ee O O Model MI 4836 E ZI WT wm CAUTION MUST HAVE 2 PEOPLE TO ASSEMBLE DO NOT E LIFT OR TILT ON SIDE Kl el BEE TOOLS REQ Screwdriver Rubber Mallet A Friend IMPORTANT DEAR CUSTOMER To ensure that you have a speedy and pleasant time assembling your unit PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE BEGINNING ASSEMBLY If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY BETWEEN 8 00 AM TO 3 00 PM PACIFIC TIME Please be sure to follow the construction order in the Assembly Manual and complete each step before you proceed to the next step Call USA Plycraft Industries Inc 2100 E Slauson Ave Huntington Park CA 90255 E mail plycraft ix netcom com Toll Free Telephone 1 800 765 9035 Telephone 1 323 587 8101 Fax 1 323 587 8220 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 LIST OF PARTS WITH QUANTITY MODEL MI 4836 E DESCRIPTION QTY WOOD PARTS LER Sid n 1 Rigbi SIG 5255 cers cecseragaseapscese cetera 1 TOD H 1 ptn 1 TOOLS REQUIRED e SCREWDRIVER e RUBBER MALLET Partition E 1 ege 1 Bottom Kicker aenescens 1 Adjustable Shelves sscsscssscssseeseeees 4 B ck Panek EE 2 ESTIMATED ASSEMBLY TIME 30 M2. 19 Install 2 Long Screws through the predrilled holes of each cleat of the TOP KICKER and into the TOP DO NOT OVER TIGHTEN See Figure 4 Step 20 Install 2 Long Screws through the predrilled holes of each cleat of the BOTTOM KICKER and into the BOTTOM DO NOT OVER TIGHTEN See Figure 4 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 Po 7 Step 21 Lay the back panel on the back edges of the bookcase Make sure the BACK PANEL s unfinished side faces up See Figure 5 IMPORTANT Back Panel must be completely aligned with TOP BOTTOM and side edges as well to ensure a square cabinet as explained below Step 22 Position the back panel flush with the top edge of the Top Make sure the BACK PANEL does not go over the edges of the top corners See Figure 5 Step 23 Insert and screw 6 screws along the top edge of the BACK PANEL See Figure 5 BACK PANEL MUST BE FLUSH THE BACK PANEL IS Figure 5 WITH THE TOP _ CENTERED WHEN THE T SPACE AT BOTH CORNERS 1 1 T Sai IS EQUAL ON BOTH SIDES Note Back Panel consists of two panels joined by tape at the middle THE BACK PANEL IS CENTERED WHEN THE SPACE AT BOTH CORNERS IS EQUAL ON BOTH SIDES Step 24 Align the bottom corners of the bookcase with the corners of the BACK PANEL If necessary slide the corners of th
3. added safety feature we recommend to affix the bookcase to the wall We sincerely hope you have enjoyed assembling your unit and that you will make good use of it _ ADJUSTABLE S SHELF IF NECESSARY 7 2 c ADJUST ONE E SUPPORT PIN SE BY ROTATING 180 F Gi gt SHEE pk ee SUPPORT ZZ PIN Figure 8 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 PGs oO DRILLED HOLE ON THE WALL DRY WALL ANCHOR 4 pS Ae NYLON RESTAINT STRAP Furniture Tipping Restraint Information Young children may be injured by tipping furniture The use of a tipping restraint is highly recommended This hardware when properly installed could provide protection against the unexpected tipping of furniture due to improper use WARNING This product is only a deterrent It is not a substitute for proper adult supervision Installation Instructions 1 Attach one of the mounting brackets securely to the top back edge of the furniture Use one of the SHORTER screws to securely attach the bracket to bookcase 2 Determine where furniture is to be placed and mark location on the wall for the mounting bracket screw hole approximately 2 below the bracket mounted to the edge of the furniture 3 Drill a 3 16 hole in the wall Press the plastic anchor into
4. of RIGHT SIDE DO NOT OVER TIGHTEN See Figure 1 a LONG RAISED EDGE FASTENER PIN CS Se Step 4 With your friend carefully place LEFT SIDE with the small predrilled holes facing up and the long raised edge facing towards you See Figure 1 Step 5 Insert and screw 4 metal fastener pins into 4 small pre drilled holes of LEFT SIDE DO NOT OVER TIGHTEN See Figure 1 Step 6 With your friend carefully place TOP finished on both sides with the small predrilled holes facing up See Figure 1 Step 7 Insert and screw 2 metal fastener pins into 2 small pre drilled holes of TOP DO NOT OVER TIGHTEN See Figure 1 Step 8 With your friend carefully place BOTTOM with the small predrilled holes facing up and unfinished face with big holes for cams facing down See Figure 1 Step 9 Insert and screw 2 metal fastener pins into 2 small pre drilled holes of BOTTOM See Figure 1 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 PG 5 Figure 2 PLYWOOD FLAP FINISHED SIDE MUST FACE TOWARD THE FRONT a OF RT Gory unt z Ho DO lt STEAL TOP KICKER J i i i i i PLYwooD FLAP i i l Step 10 With your friend position RIGHT SIDE with the fastener pins facing up and the long raised edge toward you See Figure 2 Step 11 With your friend inse
5. the hole and gently tap until the flange on the anchor is against the wall surface 4 Position the bracket over the anchor and use one of the LONGER screws to securely attach the bracket to wall 5 Place the furniture so that the bracket on the back edge is in line with the bracket on the wall 6 Lace an end of the nylon restraint strap down through each bracket Bring both ends together and slide the beaded end of the strap through the keyhole shaped slot in the other end until snug Pull down on the beaded end until it snap locks into the keyhole slot 7 Check to make sure the strap is securely laced and locked to the brackets KIT TO SECURE BUUKCASE TO THE WALL
6. INUTES ASSEMBLE ON SOFT SURFACE TO PREVENT DAMAGE TO THE FINISH RECOMMENDED NUMBER OF PEOPLE NEEDED FOR ASSEMBLY 2 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 PG LIST OF PARTS WITH QUANTITY MODEL MI 4836 E DESCRIPTION RAWINGS NOT TO SCALE HARDWARE QTY FASTENER PINS cicera iiaii 12 QA w SHELF SUPPORT PINS 0 ssssssnsststsnsnsstsssnesse 16 Be SCREWS CLEATS 1 WE 8 famm MOUNTING BRACKETS E 2 SCREW MOUNTING BRACKET AR 1 mm NYLON RESTAINT STRAR uk 1 O DRY WALL ANCHOR 5350i0 siessedpssshusesensevesons 1 gu DRYWALL SCREW 1 Y eerti aa ea ses 1 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 PG 4 ASSEMBLY MANUAL Step 1 Please READ INSTRUCTIONS carefully before beginning Assemble in the general area you want your new bookcase to be placed IMPORTANT WE RECOMMEND THAT A FRIEND ASSIST YOU WITH ASSEMBLY FROM THIS POINT FORWARD Step 2 On a clean soft surface such as a carpet or the inside of the carton place RIGHT SIDE with the small predrilled holes facing up and the long raised edge facing towards you See Figure 1 Step 3 Insert and screw 4 metal fastener pins into 4 small pre drilled holes
7. SIDE into the holes and dowels of BOTTOM first and the TOP Make sure that the plywood flap is inside the raised edge of the side Press together firmly to close all the gaps between the BOTTOM TOP and the LEFT SIDE See Figure 2 Step 16 Install 12 Cams into the large pre drilled holes Point the arrow on the Cam in the direction of the fastener pin Push the Cam into the large predrilled hole Use a screwdriver to turn each Cam approximately 1 2 turn in the direction of the arrow clock wise to lock it in place DO NOT OVER TIGHTEN See Figure 3 Step 17 With your friend carefully turn the bookcase onto its face See Figure 4 ALIGN ARROW Wan C 8 CAM HEAD OF EE TO OPEN CAM UNLOCK FASTENER LG WITH THE SCREW DRIVER Ki Ka ALIGN TURN BACK THE ARROW ON CAM Figure 3 LARGE IN THE DIRECTION EE OF THE FASTENER PIN ai Step 18 With your friend slide the BOTTOM KICKER with the cleats facing up and finished edge band to the top of the unit under the BOTTOM until the cleats make contact with the BOTTOM Make sure that the plywood flaps are flush with the raised edges of the sides See Figure 4 NOTE If the BOTTOM KICKER does not slide easily between the SIDE PANELS under the BOTTOM open unlock cams on one side slightly tap and open the PANEL and slide the BOTTOM KICKER in When BOTTOM KICKER is in place please tap gently to close the gap between the PANELS and tighten the cams See Figure 4 and Figure 3 Step
8. e bookcase to the left or to the right Make sure the BACK PANEL does not go over the sides at the bottom corners See Figure 6 Step 25 Insert and screw 6 screws along the bottom edge of the BACK PANEL See Figure 6 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 PG 8 Step 26 The edges of the SIDE PANELS must be parallel with the edges of the BACK PANEL If necessary slightly push the SIDE PANELS in or out in order to ensure an equal amount of space along the edges See Figure 7 Step 27 Insert and screw 4 screws along each side edge of the BACK PANEL See Figure 7 Step 28 Insert and screw 2 screws with washers along the tape See Figure 7 SECH with 2 washers ics ett A WE Figure 7 Step 29 With your friend carefully set the unit upright and move to the desired location Step 30 Position and insert securely Shelf Support Pins at the desired locations 4 pins per shelf Install each ADJUSTABLE SHELF at the desired locations Step 31 If necessary adjust one Shelf Support Pin by rotating 180 at the loose corner to ensure a firm flat support for ADJUSTABLE SHELF See Figure 8 NOTE For safety it is recommended to place items on the bookcase shelves starting with the bottom shelf first working your way up the bookcase shelf by shelf to top shelf As an
9. rt BOTTOM into the holes and fastener pins of RIGHT SIDE Make sure the large predrilled holes and unfinished side are facing toward the bottom of the unit Press together firmly to close all gaps between the pieces See Figure 2 Step 12 With your friend insert TOP into the holes and fastener pins of RIGHT SIDE Make sure the large predrilled holes and the fastener pins are facing toward the bottom of the unit Press together firmly to close all gaps between the pieces See Figure 2 Step 13 CAUTION OVERSPREADING THE PANELS MAY CAUSE THE DOWELS TO BREAK TOGETHER YOU AND YOUR FRIEND MUST HOLD the TOP AND THE BOTTOM WHILE YOU INSTALL THE PARTITION With your friend carefully insert PARTITION into the holes and fastener pins of the TOP and BOTTOM Make sure to position the shortened corner at the top of the unit Figure 2 Note BOTTOM KICKER is wider than TOP KICKER Step 14 Insert TOP KICKER s plywood flap in between the right side LONG RAISED EDGE and against the TOP Press TOP KICKER against PARTITION s shortened corner and TOP Make sure the cleats and the plywood flaps are through the inside of the unit Your friend must hold TOP KICKER until step 16 is completed See Figure 2 If you need assistance DO NOT CALL THE STORE call us Our Customer Service Group Is here to help you CALL MONDAY FRIDAY between 8 AM and 3 PM PACIFIC TIME Toll Free Telephone 1 800 765 9035 PG P Step 15 With your friend carefully insert LEFT
Download Pdf Manuals
Related Search