Home Decorators Collection 1308100930 Instructions / Assembly
Contents
1. DECORATORS COLLECTION HDC 13081 MFG TW 19167DW TW 19167WO MANOR BUFFET 3 DOOR ASSEMBLY INSTRUCTIONS Note 1 Before assembly please be sure to work on a soft flat surface to avoid any damage to the finish 2 You need at least 2 people to finish the assembly of this product Made In China P 1 8 IMPORTANT NOTE READ CAREFULLY BEFORE ASSEMBLY PREVENT DAMAGE TO PARTS FOLLOWING INSTRUCTIONS LISTED BELOW IN THE PROPER SEQUENCE AS NUMBERED TO ASSURE FAST EASY AND CORRECT ASSEMBLY ASSEMBLY TOOLS REQUIRED OM Screw driver WOODEN DOWEL INSTALLATION PROCEDURE 1 FILL HOLE 1 4 FULL OF GLUE 1 2 3 2 GENTLY TAP DOWEL INTO HOLE ay WITH RUBBER MALLET OR USE HAND PRESS DO NOT USE HAMMER 4 3 WIPE AWAY EXCESS GLUE 0 HIDDEN CONNECTOR ASSEMBLY TECHNIQUES FOR LOCK NUT amp LOCK PIN 1 SET INCLUDES CAM LOCK 1PC A CAM BOLT 1PC TOOL NEEDED SCREW DRIVER STEP 1 SCREW CAM BOLT A ONTO PRE SET PLASTIC NUT ON PANEL USE A SCREW DRIVER FOR TIGHTENING ATTENTION DO NOT OVER TIGHTEN THE CAM BOLT A STEP 2 ATTACH BOTH PANELS MAKE SURE YOU HAVE INSERTED THE CAM BOLT TO THE VERY DEPTH OF THE HOLE WITH2. PARTS LIST TOP FRAME 1 PC LEFT SIDE PANEL 1 PC RIGHT SIDE PANEL 1 PC A LEFT MIDDLE PANEL RIGHT MIDDLE PANEL BOTTOM FRAME 1 PC 1 PC 1 27 ss F DOOR DOOR SHELF 1 PC p 2 PCS 2 PCS G I BACK PANEL MIDDLE BAR SHELF 1 PC 1 PC 1 L MIDDLE BAR 1 PC NOTE THE SURFACE WITH THE STICKER IS THE BACK SIDE P 4 8 STEP 1 ASSEMBLE KNOB 3 USE BOLT 3 TO ATTACH KNOB 3 ONTO DRAWER FRONT PANEL STEP 2 ASSEMBLE MIDDLE PANEL D amp E AND MIDDLE BAR K amp M FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE CAM BOLT amp CAM LOCK 2 AND WOOD DOWEL 1 TO ASSEMBLE MIDDLE PANEL amp AND MIDDLE BAR K amp M TOGETHER AS SHOWN se E S 2 R fz f N 9 CX my 7 2 Fi T g 7 lt 5 8 STEP 3 ASSEMBLE SIDE PANEL amp C MIDDLE PANEL D amp AND BOTTOM FRAME FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE amp CAM LOCK 2 AND WOOD DOWEL 1 TO ASSEMBLE SIDE PANEL
3. amp MIDDLE PANEL D amp E AND BOTTOM FRAME F TOGETHER AS SHOWN RB STEP 4 ASSEMBLE FRAME FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 USE CAM BOLT amp CAM LOCK 2 AND WOOD DOWEL 1 TO ASSEMBLE TOP FRAME SIDE PANEL amp AND MIDDLE PANEL amp TOGETHER AS SHOWN P 6 8 STEP 5 ASSEMBLE KNOB 3 HINGE 4 AND IRON SLICE 5 USE ROUND HEAD BOLT 3 TO ATTACH KNOB 3 ONTO DOOR amp H USE FLAT HEAD SCREW 4 TO ATTACH HINGE 4 ONTO DOOR G amp H USE FLAT HEAD SCREW 5 TO ATTACH IRON SLICE 5 ONTO DOOR G amp H 7 a 4 N I 3 Fa x 4 k 4 at 1 3 MINA pes 7 STEP 6 ASSEMBLE DOOR G amp H e USE FLAT HEAD SCREW 4 AND HINGE 4 TO ASSEMBLE DOOR amp ONTO SIDE PANEL B amp C AND MIDDLE BAR M USE FLAT HEAD SCREW 6 TO ATTACH MAGNET LOCK 6 UNDER TOP FRAME A P 7 8 STEP 7 ASSEMBLE SHELF
4. L amp I INSERT SHELF HOLDERS 8 INTO THE HORIZONTAL HOLES INSIDE OF SIDE PANEL amp AND MIDDLE PANEL D amp E THEN PUT SHELF L amp I ON THE RELEVANT SHELF HOLDERS STEP 8 ASSEMBLE BACK PANEL J USE ROUND HEAD SCREW 7 TO ATTACH BACK PANEL J ON THE BACK OF PRE ASSEMBLED UNIT NOTE BEFORE YOU ASSEMBLE THE BACK PANEL PLEASE MAKE SURE THE 2 SIDE PANELS AND DOORS HAVE AN EVEN GAP BETWEEN THEM IF UNEVEN SHIFT THE SIDE PANELS AND ADJUST DOORS UNTIL EVENLY SPACED THEN ATTACH BACK PANEL P 8 8
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y 3 HINGE FLAT HEAD SCREW 6 SETS TRON SLICE FLAT HEAD SCREW 3 SETS an MAGNET LOCK ROUND HEAD SCREW 3 SETS ROUND HEAD SCREW 30 PCS 7 12 5 SHELF HOLDER ae 8 9 P 3 8
Download Pdf Manuals
Related Search