Home Decorators Collection 0805400520 Instructions / Assembly
Contents
1. Home Decorators Collection HDC 08054 MFG TW 184031X TW 18403BP SOUTHPORT BUFFET 31 Hx58 Wx16 D ASSEMBLY INSTRUCTIONS Note Before assembly please be sure to work on a soft flat surface to avoid any damage to the finish Made In China P 1 8 BEFORE ASSEMBLV IMPORTANT NOTE READ CAREFULLY BEFORE ASSEMBLY TO PREVENT DAMAGE TO PARTS Following instruction listed below in the proper sequence as numbered to assure fast easy and correct assembly ASSEMBLY TOOLS REQUIRED D CA Z Screw driver Screw driver Rubber Mallet Electric drill WOODEN DOWEL INSTALLATION PROCEDURE 1 FILL HOLE 1 4 FULL OF GLUE a O 2 GENTLY TAP DOWEL INTO HOLE Mezz i WITH RUBBER MALLET OR USE HAND xi DO NOT USE HAMMER PRESS IN x 3 WIPE AWAY EXCESS GLUE P U HIDDEN CONNECTOR ASSEMBLY TECHNIQUES FOR LOCK NUT amp LOCK PIN 1 SET INCLUDES C CAM LOCK 1PC A CAM BOLT 1PC TOOL NEEDED SCREW DRIVER STEP 1 SCREW CAM BOLT A ONTO PRE SET PLASTIC NUT ON PANEL USE A SCREW DRIVER FOR TIGHTENING ATTENTION DO NOT OVER TIGHTEN THE CAM BOLT A STEP 2 ATTACH BOTH PANELS MAKE SURE YOU HAVE INSERTED THE CAM BOLT TO THE VERY DEPTH OF THE HOLE WITH RUBBER MALLET GENTLY CAUTION DO NOT USE HAMMER THEN INSERT CAM LOCK INTO PRE DRILLED H2. Xi SS A P 7 8 STEP 7 ASSEMBLE SHELF BACK PANEL S amp T AND PLACE DRAWER e USE ROUND HEAD SCREW 12 TO ATTACH BACK PANEL S amp T ON THE BACK OF PRE ASSEMBLED UNIT INSERT SHELF HOLDERS 11 INTO THE HORIZONTAL HOLES INSIDE OF MIDDLE SIDE PANEL amp Q THEN PUT SHELF 0 ON THESE SHELF HOLDERS e INSERT DRAWER INSIDE TABLE TOP PROPERLY NOTE BEFORE YOU ASSEMBLE THE BACK PANEL PLEASE MAKE SURE THE 2 SIDE PANELS HAVE AN EVEN GAP BETWEEN THEM IF UNEVEN SHIFT THE SIDE PANELS UNTIL EVENLY SPACED THEN ATTACH BACK PANEL 4 VA her Ta Z ip 8 8
3. TO ATTACH HINGE 7 amp 8 ONTO DOOR I amp J TOGETHER AS SHOWN e USE FLAT HEAD SCREW 10 TO ATTACH IRON SLICE 10 ONTO DOOR I amp J I 8 si 10 10 b 6 7 0 O 6 8 7 STEP 5 ASSEMBLE MIDDLE SIDE PANEL amp Q AND DOOR I amp J e FILL RELEVANT HOLES 1 4 FULL GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 e USE CAM BOLT amp CAM LOCK 2 TO ASSEMBLE LEFT amp RIGHT MIDDLE SIDE PANEL amp 0 AND BOTTOM F DESK TOP R TOGETHER AND INSERT THE HINGE OF THE DOOR amp J INTO THE RELEVANT HOLES ON THE DESK TOP R AND BOTTOM PANEL F AS SHOWN USE ROUND HEAD SCREW 9 TO ATTACH MAGNET LOCK 9 ONTO DESK TOP R e USE THE VELVET HOLE COVER 14 TO COVER THE RELVEVANT CAM LOCK HOLES AS SHOWN LS P 6 8 STEP 6 ASSEMBLE SIDE FRAME M amp N AND SHELF K amp L e FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 e USE ROUND HEAD BOLT amp FLAT WASHER 3 CAM BOLT amp CAM LOCK 2 TO ASSEMBLE SIDE FRAME M amp N SHELF K amp L DESK TOP R AND BOTTOM PANEL F TOGETHER si N
4. OLE ON PANEL MAKE SURE THE ARROW ON CAM LOCK C SET IN PANEL POINT TOWARD THE HOLE INTO WHICH THE CAM BOLT A HAS BEEN INSERTED AND INSERTED THE CAM LOCK C TO THE VERY DEPTH OF THE HOLE STEP 3 ROTATE THE CAM LOCK C CLOCKWISE TO SECURE CAM BOLT A BY TIGHTENING WITH A SCREWDRIVER DETAIL STEP PLEASE SEE THE BELOW PICTURE P 2 8 VERTICAL CONNECTION HORIZONTAL CONNECTION 0 1 2 Z L x k 3 4 3 4 L 2E re oo 5 5 CO WOOD DOWEL CAM BOLT ROUND HEAD BOLT KNOB DRAWER LIMIT STOPPER 26 PCS CAM LOCK FLAT WASHER ROUND HEAD BOLT ROUND HEAD SCREW 24 SETS 15 SETS FLAT WASHER 2 SETS 2 SETS V m 0 6 Om Y o 25 O a Y gt KNOB HINGE HINGE MAGNET LOCK IRON SLICE ROUND HEAD BOLT ROUND HEAD SCREW ROUND HEAD SCREW ROUND HEAD SCREW FLAT HEAD SCREW 2 SETS 2 SETS 2 SETS 1 SET 2 SETS d x BA Y ss B sm 2 L 6 Ro 8 gt AA 9 10 SHELF HOLDER ROUND HEAD SCREW FLAT HEAD SCREW VELVET HOLE COVER ALLEN KEY 4PCS 38 PCS 8 PCS 4PCS 1PC l L AS 11 12 13 14 15 GLUE 1PC av 16 P 3 8 PARTS LIST DRAWER FRONT PANEL 2 PCS DRAWER BACK PANEL 2 PCS DRAWER LEFT SIDE PANEL 2 PCS DRAWE
5. R DRAWER BOTTOM PANEL BOTTOM PANEL 2 PCS 2 PCS FPC ACROSS PANEL LEG LEFT DOOR 1 PC 1 PC 1 PC G RIGHT DOOR LEFT SHELF RIGHT SHELF 1 PC 1 PC 1 PC J LEFT SIDE FRAME RIGHT SIDE FRAME SHELF 1 PC 1 PC 1 PC LEFT MIDDLE SIDE PANEL RIGHT MIDDLE SIDE PANEL DESK TOP 1 PC 1 PC 1 PC P R BACK PANEL BACK PANEL 2 PCS 1 PC P 4 8 STEP 1 ASSEMBLE DRAWER e USE SCREW 13 TO ATTACH DRAWER SIDE PANEL C amp D AND DRAWER BACK PANEL B TOGETHER e INSERT THE DRAWER BOTTOM PANEL INTO SLOTS IN SIDE PANEL amp D e USE CAM BLOT amp CAM LOCK 2 TO FIX DRAWER SIDE PANEL C amp D AND DRAWER FRONT PANEL A e USE ROUND BOLT amp FLAT WASHER 4 TO ATTACH HANDLE 4 ONTO DRAWER FRONT PANEL A STEP 2 ASSEMBLE ACROSS PANEL G ON BOTTOM PANEL F STEP 3 ASSEMBLE LEG H e FILL RELEVANT HOLES 1 4 FULL OF GLUE INSERT WOOD DOWEL ASSEMBLE LEG H ON BOTTOM PANEL 1 INTO THESE HOLES DETAILS SEE WOODEN DOWEL INSTALLATION PROCEDURE ON PAGE 2 e USE ROUND HEAD BOLT amp FLAT WASHER 3 TO ATTACH ACROSS PANEL G AND BOTTOM PANEL F TOGETHER BY ALLEN KEY 15 e USE ROUND HEAD SCREW 5 TO ATTACH DRAWER LIMIT STOPPER 5 ONTO BOTTOM PANEL F P 5 8 STEP 4 ASSEMBLE KNOB 6 HINGE 7 amp 8 IRON SLICE 10 e USE ROUND HEAD BOLT 6 TO ATTACH KNOB 6 ONTO DOOR I amp J e USE ROUND HEAD SCREW 7 amp 8
Download Pdf Manuals
Related Search