MAAX 141V-C59 Installation Guide
Contents
1. Da a lg Cp o 2 OUTER a ROLIEK tub shreshold ROLLER e OJ TRACK TRACK wW i 5 into the shower stall as shown in SKETCH 11B With the Panel Pull facing towards the outside lift the Glass Panel and tilt the bottom over the tub threshold and inside the shower Then lift the Panel up into the underside of the Header as shown in SKETCH 11C Be certain that both Rollers are resting on the Outer Roller Track Slowly release allowing the Glass Panel to hang from the Header The Panels should hang in the Header as shown in SKETCH 11D Slide the Outer Glass Panel away from the shower head end of your tub shower stall The edge of the Glass Panel should touch the Bumpers If not the wall is not plumb amp the Glass Panel needs to be adjusted To adjust remove the Outer Glass Panel and move one or both Rollers into other holes Re install Glass Panel and re check for plumb Please note The Glass Panels should hang as low as possible to avoid water from splashing out Slide the Glass Panels back amp forth and make sure they clear the Track End Caps If necessary re adjust rollers to raise or lower the Glass Panels 120 TZ Slide both Glass Panels to one side of the enclosure Install the Center Guide on to the Track as shown in SKETCH 12A eae Slide the Center Guide to the center of the Track until the hole in the Center Guide lines up with the hole drilled in a previous step SEAL2. THE TUB SHOWER where they sit on the tub threshold Along the inside seam of the Wall Channel on both sides Apply silicone sealant to the joint where the Track inserts into the Track End Caps and to the tops of the Track End Caps where they meet the inside of the Wall Channels as shown in SKETCH 13A Seal the entire INSIDE seam where the Tub Shower meets the Tub Walls and tub threshold Apply silicone sealant to the following areas Along the Track and around the Track End Caps and Center Guide ll coer lt SKETCH 12B gt TCH 12B D ACTUAL SIZE 6 X 1 2 LONG SCREW anh Bottoms of the Glass Panels in Center Guide The Center Guide should engage the bottoms of the Glass Panels as shown in SKETCH 12B Hold Track firmly in place and secure the Center Guide to the Track with 6 Screw WARNING DO NOT OVER TIGHTEN SKETCH 13A SILICONE SEALANT
3. to wall distance DIMENSION D and re check subtraction to be certain of the correct Track Dimension Measure twice cut once Measure the Track Dimension along the length of the Track Carefully cut the Track to size Please note to obtain the best results use a 32 tooth per inch hacksaw blade and a miter box Ti SKETCH 2A SKETCH 3A a Left Track End Cap gee ATL SKETCH 4A ee es Install Track End Caps with Corner Adapters if necessary on to the ends of the cut piece of Track as shown in SKETCH 4A Place Track with installed Track End Caps on the tub threshold and check for correct length Re cut if necessary A slightly loose fit is acceptable since the ends of the Track are hidden within the Track End Caps eee See E TUB SHOWER STALL OUTSIDE TRACK PROFILE Pencil line SKETCH 5B DETERMINE LOCATION OF CENTER GUIDE HOLE Remove the Track End Caps and measure the length of the Track DIMENSION T as shown in SKETCH 5A The hole needs to be located in the center of the length of the Track Divide T in half T 2 and measure DIMENSION T 2 from one end of the Track as shown Mark a line with a pencil at the half way point on the back side of the Track as shown in SKETCH 5B Confirm location of pencil line by measuring DIMENSION T 2 from the other end of the Track It should be the same locatio
4. ANEL as shown Measure the finished wall to wall distance Dimension H at the top of the Wall Channels as shown in SKETCH 9A HEADER Dm El PROFILE Ns ION H A y I Nut installs l against the Hanging J Bracket SKETCH 10D ZIEN ANN l a i SKETCH 10C ACTUAL SIZE 8 x 7 16 LONG MACHINE SCREW SKETCH 10E Install Hanging Brackets as shown in SKETCH 10C A Insert Glass Bushings Gray into each hole at the top of the Glass Panel B Carefully slide Hanging Brackets over the Glass Panel C Align hole in Hanging Bracket with hole in the Glass Panel and secure with 10 Screw and Barrel Bolt Please note It does not matter which side the 10 Screw is installed on but if optional Robe Hook included is going to be installed it should be installed now per instructions included in the kit and the 10 Screw should be installed on the same side as the Rollers D Install Rollers on to Hanging Brackets Please note The NuT attached to the Roller must be located towards the Hanging Bracket as shown in SKETCH 10D As a starting point Install the Rollers in the mounting hole second from the top The other holes are needed for adjustments if the wall is out of plumb Install Panel Pulls as shown in SKETCH 10E WARNING ALWAYS LIFT GLASS PANELS BY THE SIDES NOT THE PANEL PULLS Panel Pa
5. H 1A A PRE FABRICATED WALL SURROUND normally has a rounded corner where the walls meet the tub threshold as shown in SKETCH 1B There are Right amp Left Track End Caps and Corner Adapters that install at each end of the Track These adjust for different radius corners as shown in SKETCH 1C Check which combination of Track End Caps and Corner Adapters are necessary for your shower First try the Track End Cap alone in the corner area of your shower Then try the Track End Cap with the Corner Adapter ROUNDED aA CORNER THRESHOLD PRE FABRICATED SKETCH 1B WALL SURROUND installed testing both positions as shown in SKETCH 1D Select the combination that fits your shower best The Corner Adapter installs into the Track End Cap as shown in SKETCH 1E Please note When installing the Corner Adapter the direction of the ARROW on the Corner Adapter should match direction of the ARROW on the Track End Cap as shown To change positions of the Corner Adapter rotate as shown in SKETCH 1F Please note The radius of the Track End Cap Corner Adapter may not match the radius of the shower precisely Find the combination where the Track End Cap lays flat on the tub threshold and the back touches the wall as shown in SKETCH 1G For extra large radius corners use the Track End Cap alone SKETC
6. H 1C SKETCH 1D SKETCH 1E SKETCH 1F ee a S Le Corner Adapter aes nn I Y ae am Lian f 7 Track End Cap 3 ne No Corner Adapter ve Large Radius iI Position 1 Right Track RA End Cap oe Shown od n Position 2 gt will be i es d fit L ea geod ra Track End Cap with tf a Corner Adapter Position 1 tub threshold SSS SS Medium Radius Jesa touch wall CORRECT o or lay flat z SKETCH 1G 3 ee e i X aes Corner Adapter should touch pe ce Track End Cap with l sea Comer Adapter Position 2 tub threshold M tub threshold Small Radius H INCORRECT tub threshold u 2 RRR WARNING SAFETY GLASSES SHOULD BE WORN AT ALL TIMES Determine if your Tub Shower Enclosure ledge is level amp walls are plumb as shown in SKETCH 2A If they are out of level plumb by more than 1 2 stop and call Customer Service A Ledge Filler and or Wall Filler is recommended for obtaining proper adjustment Both are available through Customer Service for a nominal charge Measure the finished wall to wall distance 3 dimension D in the center of the tub threshold as shown in SKETCH 3A Please note f a steel tape is used be sure to add the width of the case to the measurement Subtract 1 5 16 from DIMENSION D this is your TRACK DIMENSION At this point re measure the wall
7. K1064 0708E 5mm Installation Instructions Frameless Tub 4 i Shower Enclosure p K TUB SHOWER ENCLOSURE SAVE THESE INSTALLATION INSTRUCTIONS FOR FUTURE REFERENCE AND IN THE EVENT YOU NEED TO ORDER A REPLACEMENT PART RECORD THE MODEL GLASS FINISH FROM THE PRODUCT LABEL ON THE PACKAGE Unpacking Care should be taken when unpacking your Shower Enclosure Place the Glass Panels in an upright safe location to avoid damage Cleaning Never use scouring powder pads or sharp instruments on metal work or Glass Panels We recommend the use of a squeegee after each shower to eliminate water spots on the inside of the Glass Panels An occasional wiping down of the Glass Panels and anodized aluminum parts with a mild detergent diluted in water is all that is needed to keep your Shower Enclosure looking brand new CAREFULLY READ THE INSTALLATION INSTRUCTIONS BEFORE YOU START THIS WILL ENABLE YOU TO BECOME FAMILIAR WITH THE INSTALLATION SEQUENCES AND THE REQUIRED TOOLS Tools Required For installation of your Shower Enclosure you will need the following tools A Safety glasses H Center punch B Measuring tape l Drill Bit C Pencil 1 8 for installation on a fiberglass enclosures D Hack saw with 32 teeth per inch blade 1 4 masonry for installation on ceramic tiles or marble E Miter Box or Square J Power screwdriver F Level K 2 phil
8. e Measure twice cut once certain of the correct Header Dimension Measure the HEADER Dimension along the length of the Header Carefully cut the Header to size Please note to obtain the best results use a 32 tooth per inch hacksaw blade and a miter box Slide the Header down on top of the Wall Channels The Header is reversible ROLLER MOUNTING HOLES 10 PANEL PULL eS SKETCH 10A RIGHT PANEL TUB UNIT LEFT PANEL INNER GLASS PANEL OUTER GLASS PANEL SKETCH 10B o Jb THE PANEL PULLS INSTALL ON THE SAME SIDE AS THE ROLLERS Note INNER GLASS PANEL on left side shown Shower head would be on left side Reverse for shower head on right side Arrange the Glass Panels as they will install in the unit as shown in SKETCH 10A Glass Panels shown in front of tub for clarity The Panel Pull Holes should be located all the way to the left in the Left Panel and all the way to the right in the Right Panel The Roller mounting holes should be at the top Determine which of the Glass Panels will be the INNER GLASS PANEL and the OUTER GLASS PANEL For water sealing purposes the INNER GLASS PANEL must be on the same side as the shower head When installing Hanging Brackets and Panel Pulls orient them on the Glass Panels as shown in SKETCH 10B The Rollers and Panel Pulls install on the inside of an INNER GLASS PANEL and outside of an OUTER GLASS P
9. lips screwdriver G Electric Drill L Caulking gun Materials Required For installation of your Shower Enclosure you will need the following materials A Masking tape B Silicone sealant IF YOU NEED REPLACEMENT PARTS OR HAVE INSTALLATION QUESTIONS PLEASE CALL OUR CUSTOMER SERVICE REPRESENTATIVES WHEN CALLING FROM USA CALL 800 355 5397 Monpay FRIDAY 8 30am 4 00pm EASTERN TIME WHEN CALLING FROM CANADA CALL 888 304 4388 MONDAY FRIDAY 8 00am 5 00pm EASTERN TIME TUB SHOWER ENCLOSURE lt OUTSIDE 2 Header Bottom Track Wall Channel Outer Glass Panel Inner Glass Panel Right Track End Cap Corner Adaptor LeftTrack End Cap Bumper 10 x 1 1 4 long Screw Wall Anchor Hanging Bracket 10 x 1 4 long Barrel Bolt Glass Bushing Gray 10 x 3 8 long Truss Head Screw 8 x 7 16 long Machine Screw Panel Pull Roller 7 64 Drill Bit 6 x 1 2 long Screw Center Guide Panel Pull Wrench Robe Hook Additional Screws and Wall Anchors are included in the Parts Bags for your convenience AB A PRB RH ANAHHPAPHRAPHRP PAN A ARH HADN HK SHARP CORNER TUB THRESHOLD SKETCH 1A TLED WALLS This Door was designed to install on a TILED WALL as well as a PRE FABRICATED WALL SURROUND TILED WALLS normally have a sharp corner where the walls meet the tub threshold as shown in SKETC
10. n To mark the Height location of the CENTER GUIDE HOLE install the Center Guide on to the Track as shown in SKETCH 5C CENTER GUIDE O TRACK SKETCH lt SKETCH 5C gt bn LI TRA CK CK SKETCH 5A ACTUAL SIZE 6 x 1 2 LONG SCREW Slide the Center Guide along the Track until the pencil line shows through the Screw Boss in the back of the Center Guide as shown in SKETCH 5D Making sure to hold the Center Guide tightly down on to the Track insert a pencil in the SCREW Boss and mark the hole location Remove the Center Guide from the Track Then using a Center Punch make a dimple at the marked location This will prevent the drill bit from wandering when drilling the hole Carefully drill the hole with the Drill Bit provided Install a 6 x 1 2 long Screw into the hole in order to pre cut threads into the Track Then remove the screw and set aside Screw Boss Pencil line Pencil line A I Slide Center Guide along the Track SKETCH 5D INSIDE tub threshold SKETCH 6A Re Install Track End Caps amp Corner Adapters if necessary on to the ends of the Track and locate the Track on to tub threshold PRE FIT TRACK The back of the Track should be located in the approximate center of the tub threshold as shown in SKETCH 6A 2 SKETCH 6B When the Track positioned correctly tempora
11. nel Panel Pull not Pulls not Pulls not shown shown shown tub threshold m threshold GLASS PANEL INSTALLATION Install the Inner Glass Panel first Please note It is recommended that a second person hold the Header down so that it does not pop up during Panel installation With the Panel Pull facing towards the tub stall lift the Glass Panel and tilt the bottom over the tub threshold and inside the shower as shown in SKETCH 11A Then lift the Panel up into the underside of the Header Be certain that both Rollers are resting in the nner Roller Track Slowly release allowing the Glass Panel to hang from the Header Slide the Inner Glass Panel towards the shower head end of your tub stall The edge of the Glass Panel should touch the Bumpers If not the wall is not plumb amp Glass Panel needs to be adjusted To adjust remove the nner Glass Panel and move one or both Rollers into other holes Re install Glass Panel and re check for plumb Install the Outer Glass Panel Please note During installation the Outer Glass Panel will push slightly against the bottom of the Inner Glass Panel in order to tilt tub threshold lt SKETCH 11A gt 11A lt SKETCH 11B gt 11B lt SKETCH 11C gt 11C lt SKETCH 11D gt 11D er Header pr uf a z J D a a plo E AQ m z be iN Panel a Pulls not m shown e wy N 2 5 egs j UX BEd
12. rily secure the Track to the tub threshold with masking tape as shown in SKETCH 6B Mark the Track location with a pencil SKETCH 7B yy SKETCH 7A gt PRE FIT WALL CHANNELS Carefully position the Wall Channel by sliding it down on to the Track End Cap as shown in SKETCH 7A The SHORT LEG of the Wall Channel should face the inside of the shower as shown in SKETCH 7B Be careful not to move the temporary position of the Track Use a level to plumb the Wall Channel as shown in SKETCH 7C Mark the two mounting hole locations of the Wall Channel SHORT LEG FACES INSIDE OUTSIDE LEVEL SHORT LEG OF WALL CHANNEL For reference iI _J The hidden part of the Track End Cap shown in DASHED lines f SKETCH 7C Repeat this procedure for the other Wall Channel Remove Wall Channels and Track Drill marked mounting holes Size of holes are as follows When mounting to ceramic tile use a 1 4 masonry drill bit Nick the ceramic surface at the mounting hole locations with a center punch After drilling insert Wall Anchors When mounting to a fiberglass enclosure use a 1 8 drill bit Wall Anchors are not required 3 beads of silicone sealant Ss gt K Track End Cap l j with Corner Adapter installed of J SKETCH 8A Y Silicone sealant s con
13. tinuos bead gt a SX of silicone sealant a Track End Cap 1 without Corner Adapter installed Track INSTALL TRACK amp WALL CHANNELS After drilling holes clean the tub threshold and the Wall Channel areas thoroughly This will ensure proper adhesion of the silicone sealant Before installing the Track apply silicone sealant as specified in SKETCH 8A Apply 3 beads of silicone sealant as shown when Corner Adapter is installed Apply 1 continuous bead of silicone sealant as shown when Corner Adapter is not installed Apply continuous beads of silicone sealant into the SILICONE GROOVES located on the underside of the Track as shown in SKETCH 8A HIGH SIDE SKETCH 8B Position the Track on the tub threshold aligning it with the pencil mark from the previous step INSIDE OUTSIDE TRACK PROFILE REMEMBER the high side of the Track must be placed toward the outside of the tub threshold Install Wall Channels using the 10 x 1 1 4 Screws and Bumpers provided as shown in SKETCH 8B ACTUAL SIZE 10 x 1 1 4 LONG SCREW 9 Please note If a steel tape is used be sure to add the width of the case to the measurement Subtract 1 16 from DIMENSION H this is your HEADER DIMENSION At this point re measure the wall to wall distance DIMENSION H and re check subtraction to b
Download Pdf Manuals
Related Search