American Standard 4834.ST.021 Installation Guide
Contents
1. 6032 STRH 6032 STLH SPECIFICATIONS AN Product No 3232 ST 3636 ST 4242 ST 6032 STLH O Size 32 x 32 36 x 36 3 16 42 1 8 x 42 1 8 60 x 32 16 813 x 813mm 914 x 919mm 1070 x 1070mm 1524 x 813mm 406mm Product No 4834 ST 6034 ST 3636 NEO 6032 STRH i Size 48 1 8 x 34 1 4 60 1 8 x 34 1 8 36 1 4 x 36 1 8 60 x 32 8 1222 x 870mm 1527 x 867mm 921 x 918mm 1524 x 813mm 203mm Product No 3838 NEO 4242 NEO 4832 ST s saamin Size 38 1 8 x 38 1 16 42 1 4 x 42 1 8 48 x 32 968 x 967mm 1073 x 1070mm 1219 x 813mm 36 A Insure the floor and stud walls are square and plumb Provide a 5 x 5 127mm x 127mm opening in the floor for the drain see Figs A amp B The drain plug accom modates a 2 51mm PVC waste pipe The waste pipe should extend above the surface of the sub floor refer to chart on page 2 for the required dimensions See product drawings on this page for the specified drain locations 36 NEO 3838 NEO 4242 NEO 3232 ST 3636 ST 4242ST 6034 ST 4834 ST 4832 ST a 90 51 mm 2 127mmx127mm a q r 51 mm 2 PVC Waste Pipe 5x5 Opening PVC Waste Pipe Gil os Opening See Product Chart for Drain Location 90 See Product Chart for Drain Location B SHOWER BASE 3636 NEO 3838 NEO 4242 NEO 3232 ST 4834 ST 6034 ST 3636 ST 4242 ST 4832 ST 6032 STRH LH WASTE PIPE HEIGHT 5 16 1 16 3 82. 1 16 5 16 1 16 3 8 1 16 1 4 1 16 1 4 1 16 1 4 1 16 5 16 1 16 1 2 1 16 1 2 1 16 Note Variations in levelness of the subfloor may require adjustment of waste pipe height For 6032 STRH and 6032 STLH see drawing for proper location of 5 x 5 drain cut out DRAIN Strainer ASSEMBLY Rubber Gasket Before installing drain into the shower base remove strainer see Fig C This will be installed after sh Body Silicone ower base is in its final Sealant es Base position Install the drain to the shower base as shown in se body and shower base No Bedding 159mm 6 5 8 D Rubber Gasket Fig D Use silicone Gasket alant between drain Locking Nut SS Waterproof Drywall 13mm 1 2 minimum Under Bedding Material Area gt Apron I t Bedding Material 51x102 mm 2x4 Stud Wall Draw a line 6 5 8 159mm from the sub floor on to the studs at each side of the opening Using this line and a level mark the remaining studs See Figs A amp B This will be the installed height of the shower base Mix the low shrink bedding material grout mortar plaster etc Concrete is not recommended Apply enough bedding material to support the entire bottom of the shower base The bedding material must not be used under the apron front edge Lift
3. abrasive cleaners a mixture of warm water and a mild liquid detergent is adequate for most cleaning Strong detergents formulated for use on tile or porcelain enamel surfaces should be avoided Caution Do not allow liquid detergent containers to remain on base surfaces for more than a few moments Do not use Lestoil Windex Mr Clean Dow Disinfectant spray or concentrate or Lysol Basin Tub and Tile Cleaner Do not allow nail polish remover dry cleaning fluid acetone paint remover or other solvents to contact acrylic surface 751817 100 Rev R
4. and lower base over center E of drain pipe and set into place FOR AFTER SALES SERVICE CALL 1 800 442 1902 AS America Inc 2010 After the bedding material has been poured and before it sets lower the shower base into position with the drain assembly sliding over the waste pipe as shown in Fig E It will be necessary to rock the shower base until the top of the tile flange aligns with the lines drawn in Step 3 on the stud walls Make certain the apron is contacting the rough floor along the entire length of the shower base Insure that the base is level in two directions see Fig F Snap strainer back into place and check for proper drainage Level l SA F Level base in two directions Note Allow the bedding material to completely harden before applying weight to the bottom of the shower base Tape over the strainer to protect the finish and prevent construction debris from entering the drain Finish installation as shown in Figure H Tile Waterproof Drywall Tile Adhesive stud m x Splash Lip Flange CLEANING AND MAINTENANCE Your American Standard shower base is designed to last indefinitely with reasonable care and maintenance The high gloss acrylic surface is resistant to impact and retains its luster with proper care and maintenance An integral slip resistant surface is incorporated for user safety General Cleaning Do not use
5. American Standard Installation Style That Works Better Instructions ACRYLIC SHOWER BASE MODELS 3232 ST 3636 ST 4242 ST 4832 ST 4834 ST 6032 STLH 6032 STRH 6034 ST 3636 NEO 3838 NEO 4242 NEO Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI 2124 2 For alcove ST models installation only Observe local plumbing and building codes The opening dimensions should be 1 8 larger than dimensions shown 751817 100 Rev R NOTE Read instructions completely before proceeding with installation 3636 NEO 3838 NEO 4242 NEO i lt 17 7 8 i j lt 19 7 8 24 454mm 505mm A 610mm 656mm 25 13 16 454mm 17 7 8 318mm 12 1 2 aren 12 1 2 mm 494 2 7 aut 318mm eeu 38 1 8 42 414 968mm 1073mm 3232 ST FRONT 4834 ST FRONT 6034 ST 34 1 4 oe 870mm O i Yz 16 3 4 425mm 24 1 16 30 611mm 60 1 8 ie 48 1 8 1222mm ed 4242 ST FRONT i070mm mm i 20 3 4 iil el 121mm 533mm 42 1 8 1070mm FRONT lt
Download Pdf Manuals
Related Search