Vigo VG06068WHT36 Installation Guide
Contents
1. DELINES FOR UNIT INSTALLATION SHOWER PAN MODEL VG06069XXX36 MODEL VG06069XXX38 MODEL VGO6069XXX40 MODEL VGO6069XXX42 MODEL VGO6069XXX47 GUIDELINES FOR UNIT INSTALLATION SHOWER PAN Refer to drain manufacturer for proper drain installation methods and instructions FIGURE 2A BIE UNIT Framing Requirements INSTALLATION CONFIRM DRAIN Due to individual site variations exact PROCEDURE ALIGNMENT guidelines for every situation cannot be supplied The recommended framing and dimensional requirements shown are for a typical application and may depending on site requirements FASTENING IT IS IMPORTANT THAT THE FLOOR AND ALL FRAMING BE SQUARE AND LEVEL POSITION JHE WoO Framing should be done using accepted FRAMED AREA materials and construction techniques in p accordance with all applicable codes Make yen sure to use materials that will properly fill open CONFIRM BOTTOM OF FRONT voids between the base and sub floor while aie Pees ene TE An maintaining the intended functionality of the LENGTH OF PAN base IMI n GR FIGURE 2B CONFIRM THE SHOWER PAN IS UNIT LEVEL FROM FRONT TO BACK l INSTALLATION ACCROSS EACH END OF THE Installation Procedure PROCEDURE With the unit positioned in the alcove several details must be checked prior to securing the unit in place Figure 2a 2b and Figure 2c Conf2. MODEL VG06019 MODEL VG06029 MODEL VG06049 MODEL VG06039 MODEL VG06069 MODEL VG06068 GUIDELINES FOR UNIT INSTALLATION SHOWER PAN MODEL VG06029 MODEL VG06068 MODEL VG06039 MODEL VG06069 MODEL VG06049 MODEL VG06019 A careful review of these procedures and any referenced publications before starting is important in avoiding unnecessary problems resulting in an improper assembly or installation NOTE All drawings in this publication are typical and may appear different than the actual items being installed In addition optional items may be shown on the units which may not have been ordered on the unit being installed Special Notes to Installer elt is the sole responsibility of the installer to determine prior to the installation the requirements necessary for compliance with all codes involving the unit or the installation eAll paperwork packaged with the unit and any associated options or accessories should be saved and presented to the homeowner upon completion of the installation eAll published unit dimensions are for reference only Any critical dimensions required for installation should be taken directly from the unit being installed eAny independent changes made to the unit or to any options and accessories supplied with the unit beyond those required for normal installation can void all warranties Refer to warranties for further information Inspection Guidelines A careful check o
3. SURFACE EXTREME CAUTION is urged regarding the use of any cleaner acid or solvent on the unit surface READ AND FOLLOW ALL PACKAGE LABELS AND INSTRUCTIONS Through routine use the unit surface can collect residues from soap bath additives and natural body oils Additional deposits can also collect from minerals or particles found in the water After each use wipe the excess water from the unit This practice will reduce the buildup of deposits and help maintain the natural unit lustre Following a thorough surface cleaning an application of quality automotive wax will help reduce major accumulations The actual schedule for cleaning and waxing will depend on unit usage and water quality WARNING AVOID APPLYING WAX TO THE UNIT BOTTOM Routine Cleaning Mild non abrasive cleaner specifically formulated for gelcoat and acrylic surfaces recommended Rinse surface thoroughly Heavy Soap Deposits Liquid ammonia household cleaner applied full strength Rinse surface thoroughly Stubborn Stains Liquid household cleaner or hydrogen peroxide applied full strength Place a saturated clean rag directly on stain and let stand several hours Rinse surface thoroughly For extreme cases buff area with white automotive polishing compound until stain disappears and apply a quality automotive wax to surface Hard Water Scales Liquid scale remover or white vinegar applied full strength Rinse surface th
4. UNIT TO 8 FRAMING WITH 1 1 4 SCREWS WALL FRAMING CAUTION PROTECT UNIT SURFACE WITH A SHIELD WHEN FASTENING FIGURE 4 WALL FINISHING WATER RESISTANCE UNDERLAYMENT FURRING STRIP OR SHIM MATERIAL WALL FRAMING FASTENING FLANGE WARNING THE UNIT BOTTOM SHOULD BE CLEAR OF ALL POTENTIALLY DAMAGING DEBRIS AND THE SURFACE PROTECTED BEFORE STEPPING INSIDE CAUTION It is advisable to protect the unit surface with a thin plywood or cardboard shield while fastening the flange to the framing Water Supply and Drain Connections Refer to and follow the assembly and installation instructions provided with the supply valves and drain system Carefully check all fittings and connections for leaks Finishing Guidelines Furring strips or filler material may be required over the framing to ensure the underlayment will lie flush over the fastening flanges Figure 4 A water resistant underlayment is recommended on areas surrounding the unit Stop the underlayment 1 16 to 1 8 inch from the unit surface and fill the space with a continuous bead of waterproof sealant Carefully fasten the underlayment near the unit to avoid damaging the unit surface Seal the seams and edges of the underlayment as required and install the finish material to specifications Figure 4 WARNING NEVER USE ABRASIVE MATERIALS NOR ABRASIVE CLEANERS ON THE UNIT
5. f the unit should be conducted upon receipt Notify your supplier immediately if any questions or problems are encountered during this process DO NOT INSTALL ANY UNIT WITHOUT FIRST ADDRESSING QUESTIONS WHICH ARISE DURING THE INSPECTION Basic Module Check e Check that the unit drain matches the bathroom drain location e Check for unit surface damage e Check unit color for coordination to other bathroom fixtures Options Accessories Check An individual check list is included with the assembly and installation guidelines of factory authorized options Refer to listed publications for further information before continuing GUIDELINES FOR UNIT INSTALLATION SHOWER PAN MODEL VG06029XXX36 MODEL VG06029XXX40 MODEL VG06039XXX36 MODEL VG06039XXX40 GUIDELINES FOR UNIT INSTALLATION SHOWER PAN MODEL VG06049XXX6032C MODEL VG06049XXX6036C GUIDELINES FOR UNIT INSTALLATION SHOWER PAN MODEL VG06068XXX3636 MODEL VG06068XXX3838 GUIDELINES FOR UNIT INSTALLATION SHOWER PAN MODEL VG06019XXX3240 36 1 8 MODEL VG06019XXX3248 MODEL VG06019XXX3636 48 1 8 MODEL VG06019XXX3648 GUI
6. irm dam is resting flush on the floor Confirm drain alignment Confirm the top of unit is level on all sides Confirm the unit is square in the alcove framework 2 LEVEL THE Confirm the front inside corner is plumb RIED kasi IN at each end This is critical for the proper installation of an enclosure FASTENING CONFIRM BOTTOM OF FRONT DAM IS RESTING FLUSH ON THE FLOOR ALONG THE ENTIRE LENGTH OF PAN The unit must be positioned square in the FIGURE 26 NR SHOWER FAN is alcove framework The use of shim or filler UNIT LEVEL FROM FRONT TO BACK material behind the fastening flange at each INSTALLATION ACCROSS EACH END OF THE framing member may be required to maintain PROCEDURE UNIT the unit in the proper position After the unit is confirmed leveled and square in the alcove predrill holes that are in alignment to the stud or framing Secure the unit in place across the back wall first followed by the flanges at each end using 1 1 4 inch long screws or other appropriate fasteners Continuously check to confirm the base remains square within the alcove as it is being secured Figure 3a and 3b FASTENING FLANGE 3 SQARE THE SHOWER PAN IN FRAMED AREA GUIDELINES FOR UNIT INSTALLATION SHOWER PAN FIGURE 3A SECURING UNIT _ DRILL HOLE THROUGH FLANGE AT EACH FRAMING MEMBER WALL FRAMING FASTENING FLANGE SECURE
7. oroughly Mold Mildew Liquid mildew remover or baking soda and water paste Apply paste and allow to fizz several minutes Rinse surface thoroughly Construction Adhesive Soften adhesive with hand held dryer and peel off adhesive Caution is advised when using any electrical device near water For stubborn cases apply rubbing alcohol or nail polish remover full strength to adhesive Rinse surface thoroughly WARNING BATH MATS OR OTHER ITEMS WHICH ARE HELD IN PLACE USING SUCTION AGAINST THE UNIT SURFACE MUST BE REMOVED FROM THE FLOOR OF THE UNIT AFTER EACH USE OVER A PROLONGED PERIOD FAILURE TO REMOVE THESE TYPES OF ITEMS FROM THE BOTTOM OF THE UNIT CAN RESULT IN SURFACE DAMAGE
Download Pdf Manuals
Related Search