Barclay Products TKCTR60-CP5 Installation Guide
Contents
1. K 6 Rectangular Cat No GY Shower Unit 4190 4192 Barclay lor sonin spec INSTALLATION INSTRUCTIONS Parts Included Tub Spout 195 S e Gooseneck Riser Pipe 196 R e e Wall Support Bracket w Screws 4195 WS e Shower Head 1003 Tools Needed e Screwdriver Level e 1 4 Drill Bit e Wrench Wood Screws Set Screw 1 Before beginning any work be sure to shut off the water supply 2 Apply teflon tape to ends of both the hot and cold supply nipples Place valve body through holes in tub Thread the large locknuts onto the other ends of the nipples and secure the shower set to the tub 3 Assemble shower head to gooseneck riser pipe 4 Slip the wall bracket over the straight end of the riser pipe Carefully slide the bracket to the appropriate position approximately half way up the rod and tighten the set screw provided 5 Assemble riser pipe to the riser coupling assembly on the spout by tightening the coupling nut After hand tightening fasten securely by using a wrench 6 Secure wall support bracket to the wall using the wood screws provided 7 Turn on water supply NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish Pg 1 4 14 09 P2. 84724491234 www barclayproducts com 4 Water Supply Hookup Kit Cat N p ater Supply up Ki at No q for Tub with Legs 5576 ATCAY INSTALLATION INSTRUCTIONS Parts Included e 4 Cone Washers A 2 Decorative Locknuts B Left Supply Tube C e Right Supply Tube D 2 Escutcheons E 2 Locknuts F Tools Needed e Adjustable Wrench Set of Crescent Wrenches Pliers Teflon Tape use as a sealant on all male threaded tubing This water supply tube kit includes the parts listed above ONLY The faucet in your bathtub should be purchased previously and separate from this kit To Assemble Tubes 1 First be sure to shut off the the water supply Remove old water supply tubing Put a cone washer A with the wide end of the washer inward onto the upper end of the left supply tube C 2 Slide a decorative locknut B up to the top of the left supply tube C and put on a cone washer A 3 On the bottom of the left supply tube C slide one of the escutcheons E up the tube partway then slide the locknut F up the end of the tube C directly under the escutcheon 4 Put another cone washer A with the wide end of the washer upward onto the bottom end of the tube C 5 Repeat steps 1 4 using the right supply tube D To Install Tubes 1 Attach the bottom end of the left supply tube C to the water supply tubing in your floor by screwing the locknut F down tightly Let the escutcheon E slide dow
3. n to the floor 2 Attach the upper end of the left supply tube C to the cold side faucet supply tube located on the rear of your tub by inserting the supply tube C into the faucet supply tube and tightly screw the decorative locknut B over the two for a tight fit 3 Repeat steps 1 2 using the right supply tube D and connecting it to the hot side faucet supply tube NOTE Please seek professional help if you have copper plumbing in your home Cleaning Instructions Wipe this whole set off with warm water and a soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish 10 30 07 P 847 244 1234 www barclayproducts com E Leg Tub Cat No Barclay D rai n 5599 for something sperial INSTALLATION INSTRUCTIONS Parts Included e Top Overflow Tube 1 Bottom Shoe 2 Top Waste Flange 3 Face Plate 4 Exposed Tee 5 e Face Sponge Gasket 6 e Waste Gasket 7 Lift Stop 8 2 1 1 2 Nut and Washers 9 Face Plate Screw 10 1 1 2 x 6 Tube 11 1 1 2 O D Escutcheon 12 Tools Needed e Wrench e Pliers Teflon Tape use as a sealant on all male threaded tubing Tube Cutter Plumbers Putty To Assemble Tubes 1 Assemble 3 and 8 screw into 2 7 is on top of 2 beneath the tub Place a bead of plumbers putty around bottom of 3 to seal to tub and pro
4. tect from leaks Then tighten 3 into 2 2 Assemble overflow Follow diagram 3 Set 1 in place 4 Place Tee 5 on shoe Cleaning Instructions 5 Trim bottom of tube 1 to fit into Tee 5 Wipe this whole set off with warm water and a 6 Trim tube 11 to fit soft cloth DO NOT use soaps cleansers or brass cleaners as they will disintegrate the 7 Tighten the nuts protective lacquer coating and leave the brass exposed causing it to tarnish NOTE Please seek professional help if you have copper plumbing in your home 1 8 08 P 847 244 1234 www barclayproducts com
Download Pdf Manuals
Related Search