Ella EW-SS-A-STD Installation Guide
Contents
1. Fig 3 www ellasbubbles com Page 39 08 14 e Q Installation ACCESSIBLE BATHROOMS CORNER SHOWER SEAT INSTALLATION Trim amp Test Fit Corner Seat 1 Place Corner Seat into shower area to assess placement 2 Check to see if the Seat is level Fig 4 Fig 4 3 View bottom Corner Seat and how it aligns with shower base For Corner Seat to sit flush against the shower base the bottom corners and bottom edge will need to be trimmed Fig 5 Fig 6 4 Measure the width of shower base flange The Corner Seat must sit flush on top of this flange Fig 5 5 Transfer measurement to bottom of Corner Seat on both sides Fig 6 www ellasbubbles com Page 40 08 14 e Q Installation ACCESSIBLE BATHROOMS CORNER SHOWER SEAT INSTALLATION Fig 7 Fig 8 Fig 9 7 Trim bottom of Corner Seat with jigsaw Fig 8 Cut sprayfoam backing as needed when trimming 8 Notice the bottom corners and how they are notched circled to fit on top of the shower base Fig 9 Fig 10 Fig 9 shows the Corner Seat upside down Fig 10 shows the Corner Seat test fitted on top of the shower base Fig 10 NOTCH CLOSE UP www ellasbubbles com Page 41 08 14 e Q Installation ACCESSIBLE BATHROOMS CORNER SHOWER SEAT INSTALLATION Fig 11 Fig 12 9 Test fit Corner Seat View how the bottom of the Corner Seat fits on top of the Shower Base Check to make sure the Corner Seat is level Fig 112. previously mentioned that allows for an 1 8 of acrylic or wall material and 1 8 of tape and adhesive If the tile is 3 8 thick the bullnose edge would be cut at 5 8 www ellasbubbles com Page 20 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS PLUMBING WALL INSTALLATION CONTINUED BULLNOSE EDGE FINISHES CONTINUED OPTION 2 Tri Guard Under Wall Panel Image II The tri guard will need to be installed before the wall panel Step 1 Measure from the floor to the ceiling Step 2 Mark the measurement on the tri guard and cut it with tin snips Step 3 Place a thick bead of silicone on the inside of the tri guard and push firmly into place Image JJ Q Ti p Butyl tape can also be used to adhere the tri guard Q Tip When measuring for your wall panel width you will want to keep the bullnose edge a 1 g to a 14 from the return wall edge so there is a place to apply a finishing bead of silicone Image KK Q Tip Cut the bullnose edge on the wall panel during the cutting step Cut the bullnose edge at 14 This allows room for 1 3 of acrylic or wall material and 1 3 of tape and adhesive OPTION 3 Tri Guard Over Wall Panel Image LL This will be done after the wall is installed Step 1 Measure from the floor to the ceiling Step 2 Transfer the measurements to the tri guard then cut with tin snips Step 3 Place a thick bead of silicone on the inside of the tri guard and push firml
3. 10 Mark the bottom where the Seat needs to be trimmed Fig 12 Fig 13 11 Trim bottom of Corner Seat as needed Fig 13 12 Test fit Corner Seat again 13 Trim and test fit as needed 14 Use a level to ensure the Corner Seat will be installed properly 15 Shim and level as needed www ellasbubbles com Page 42 08 14 e Q Installation ACCESSIBLE BATHROOMS CORNER SHOWER SEAT INSTALLATION Installing Corner Seat Once the Corner Seat is properly placed with shims as needed and level begin the final installation Fig 14 1 Pre drill holes through Corner Seat flanges into the frame previously built 2 Attached Corner Seat to studs through pre drilled holes with screws Fig 14 Fig 15 3 Measure cut and attach drywall to wall frames Fig 15 www ellasbubbles com Page 43 08 14 e Q Installation ACCESSIBLE BATHROOMS CORNER SHOWER SEAT INSTALLATION Add Acrylic Wall Surround Install acrylic walls around the Corner Seat Refer to Ella Installation Manual for more information Fig 16 1 Cut walls to fit around the Corner Seat Fig 16 2 Install walls following steps in Installation Manual 3 Apply final silicone seal around all seams www ellasbubbles com Page 44 08 14 0000000000000000000 N ella ella ella ello eljo ella ella eljo eljo eljo eljo eljo ello ello eljo eljo ella eljo ella ella eljo ella ella eljo ello August 2014 00000000
4. AE ey NI NINNI WaliVa Wa AV LINDYN www ellasbubbles com Page 30 08 14 e Q Wainscoting ACCESSIBLE BATHROOMS WAINSCOTING INSTALLATION CONTINUED Step 9 Wipe down the back of your wainscoting with a clean rag and denatured alcohol Place one end of the panel against the wall first and press the rest into place Step 10 Remove the slip sheet and wipe down the panel OUTSIDE CORNER TRIM INSTALLATION Step 1 Measure the height first from top of wainscoting to the floor at each corner Add 1 8 to account for extra material at the top Record the measurement Image G Step 2 Transfer measurement to the outside corner trim Cut the corner trim with tin snips being very careful to keep your hand steady Image H Step 3 Test fit for the return The top piece should sit on top of the wainscoting Hold the corner piece to the adjacent edge and scribe accordingly Image G Q Tip Installing corners varies depending on the bathroom Be sure to take your time because you may have to test fit measure and cut a few times to get the perfect fit Step 4 Install the outside corner piece by stretching and applying butyl tape on the inside of the piece Push the corner piece into place INSIDE CORNER TRIM INSTALLATION Step 1 Measure the height of the wainscoting adding 1 8 for the material at the top of the trim Hold a straight edge against the wainscoting to measure the depth again adding 1 8 for material Re
5. _I Utility Knife Stanley Swivel Lock LJ Sharpie Felt Pen LJ Butyl Tape Primer J Rags I Silicone Primer amp Cotton Swabs I Denatured Alcohol 160 Heavy Duty Yardstick J Steel Rafter Square 16 x24 I Levels 24 48 and 72 I Pliers I Hook Tool I Chisel I 3 Way Razor Scraper I Teflon Tape J Allen Wrenches J 1 1 4 and 2 Hole Saws LJ Heavy Duty Caulk Gun 4 4 Heavy Duty Wall Stripper www ellasbubbles com I 5 in 1 Painters Tool LJ Drop Light with 6 Cord or Flash I Work Table L 8 Shower Arms LJ Pipe Wrench J Adjustable Wrench J Vise Grip I Channel Locks I Handle Puller J Internal Pipe Wrench J Adjustable Slip Nut Wrench J Tube Cutter J Toilet Tank to Bowl Gaskets I Bolt Kits J Wax Mounting Seal I Toilet Supply Line 12 and 16 I White Soap Dishes w and w o handle and grout J Razor Blades J First Aid Kit J Jigsaw Blades LJ Scratch Remover Kit _I Scratch Repair Kit J Printed Cleaning Instructions LJ Copy of Warranty I 8 and 50 Extension Cords I Cutters LJ Wire Brush I Tool Apron J Drill Bits Metal and Masonry J Wall Anchors I Tool Box or 5 Gallon Pail L Suction Cup I Drop Cloths L Shop Vac I 3 8 Studs _I Broom amp Dust Pan J Hack Saw d x20 Drill amp Tap L Combo amp Handle I Wonder Pry Bar I File J Magnetic Drive Guide L Stud Finder L Nail Punch Set Page 4 I Sheet Rock Scr
6. CONTINUED Step 10 Make sure the primer is dry to the touch and apply the butyl tape on top of the primed areas Press firmly when installing so the butyl tape does not pull up when you remove the release paper Image CC Step 11 Remove the release paper Apply the silicone in between the butyl tape in a Z pattern keeping the bead about 1 4 thick Image DD Step 12 Clean the back of the new panel with denatured alcohol or damp cloth Press the panel firmly into place Image EE Remove the slip sheeting and wipe down the panel to ensure it is secured PLUMBING WALL INSTALLATION BULLNOSE EDGE FINISHES O There are three options for finishing the ends of your side walls Option 1 the bullnose edge Option 2 the use of a tri guard under the wall panel or Option 3 the use of a tri guard over the wall panel OPTION 1 Bullnose Edge Image FF Step 1 If the tile extends to the end of the wall you will need to remove the last row of tile Place a drop cloth over the floor and existing tub or shower base Step 2 Score along the edge of the tile to prevent damage to the existing wall and remaining tiles Image GG Step 3 Break out the first row of tile with a hammer and small pry bar Image HH Q Tip If you notice extensive damage to the corner bead mud and sand the wall Step 4 The bullnose edge will be cut during the cutting step of plumbing wall installation O Add the existing tile thickness measure to the 4
7. GFCI protected circuit using 10 gauge wire Frame of the tub has been properly grounded Door Seal has been cleaning with rubbing alcohol to remove any dust or debris left over from construction ___Temperature Control Valve operated on both hot and cold settings ___Both diverters function properly ___Hand Shower functions on all settings without leaking ___AIl supply lines have been checked for leaks while both diverters are on Drains open and close properly and the locking nut has been tightened on both stoppers Door seal is water tight after tub has been filled for a minimum of 20 minutes After running for a minimum of 20 Minutes both the Hydro and Air Pumps are functioning properly and all connections to the pumps and jets are water tight Chromatherapy Light and the Ozone Sterilization are working properly When the Ozone is on by itself it will make a light humming noise All drain fittings have been checked for leaks while the tub is draining Unit is installed with access to both plumbing and electrical connections www ellasbubbles com Page 47 08 14 a C Warranty Activation Form ACCESSIBLE BATHROOMS OWNER S INFORMATION Name Address City State Zip Telephone Email Date Signature Model Serial Number Purchase Date Purchase Price Place of Purchase Contact Name Phone Number Copy of sales receipt must be included with warranty activation forms To activate manufacturer s warrant
8. the codes in the city where you are working It is quite possible that a plumber may have to do this work Step 1 Remove the hardware Step 2 Take off the plumbing fixtures and accessories which includes the faucet showerhead shower grab bars soap dish and any other fixtures DO NOT remove the overflow cover It will be removed later Image A Step 3 If the existing tile does not go all the way to the ceiling pad out the existing wall above the tile to ensure the wall is flush O Tip Keep 14 and 1 2 drywall sheets in your vehicle Step 4 To pad the wall start by measuring the section of the wall that needs to be built out Transfer the measurements to the drywall then cut the drywall according to your measurements Step 5 Add silicone to the back of the drywall then press it onto the existing wall Screw the drywall onto the existing wall to keep it secure Image B Tip Though drywall is the recommended way to repair a damaged wall you may need to add additional layers of butyl tape to fir out the wall flush to the existing tile Please note butyl tape is 1 8 thick so you will need to assess the proper amount needed to fill the space Layer the tape one strip on top of another as needed Pull the release paper as you layer until you have the exact thickness Step 6 Clean the existing wall and tub system with industrial strength cleaner and denatured alcohol Remove all of the old caulk around the perimeter of th
9. the perimeter and from side to side in lines approximately 5 to 9 inches apart Image L Q Ti p If primer spills WD 40 can be used to remove it Step 16 Make sure the primer is dry to the touch and apply the butyl tape on top of the primed areas Press firmly when installing so the butyl tape does not pull up when you remove the release paper Tip If the tape is applied too close to an inside corner and comes in contact with the silicone it may discolor the finished silicone due to the carbon black in the butyl tape Step 17 Remove the release paper Apply the silicone in between the butyl tape in a Z pattern keeping the bead about 1 4 thick Step 18 Clean the back of the panel with denatured alcohol To ensure proper adhesion throughout press the ends of the panel near the plumbing and back walls into place first then work your way towards the center Make sure to apply even pressure throughout and push up on the panel to adhere it to the ceiling Step 19 Remove the slip sheeting and wipe down the panel to ensure it is pressed firmly into place www ellasbubbles com Page 16 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS SOAP DISH WALL INSTALLATION Step 1 Install corner reinforcements Corner reinforcements are part of the triple gasketing system and are used to square up the walls and provide a more permanent seal Start by measuring from the top of the tub or shower base to the ceiling and record the measu
10. 000000000 0 DOODODODODODOOODOOODDDDVD VD O eilo ACCESSIBLE BATHROOMS Ella s Bubbles LLC warrants to the owner of its ACRYLIC WALL LINERS as follows Ella s Bubbles LLC warrants acrylic showerliners acrylic wall surrounds and acrylic accessories sold to residential buyers to be free from chipping peeling cracking or fading for as long as the buyer owns the residence These guidelines expressly prohibit the use of any abrasive cleansers and damage resulting from their use that would not be covered under the terms of this warranty Since any fixture including a new one can be chipped or scratched by hard objects impacting the surface we cannot warrant against this type of damage or any acts of God In addition the following items or conditions could damage the acrylic surface and therefore void this warranty damage resulting from contact with dyes paints inks certain cosmetics or unapproved cleaning agents drain cleaners abrasive pads pigments certain foods paint remover fingernail polish remover solvents or other chemicals cigarettes or other sources of extreme heat or damage resulting either directly from misuse or abuse whether deliberate or unintentional The cause of any damage or defect shall be determined by Ella s Bubbles LLC in its sole discretion In the event of a legitimate failure of the acrylic surface under these terms Ella s Bubbles LLC reserves the right to partially repair completely rep
11. Page 23 e Q Wall Surrounds ACCESSIBLE BATHROOMS PLUMBING WALL INSTALLATION CONTINUED Step 1 Measure from the ceiling to the center of the shower arm hole Measure from the soap dish wall to the center of the shower arm hole Write down your measurements Image A Step 2 Measure from the ceiling and from the soap dish wall to the center of the mixer valve Record your measurements Image B Step 3 Measure down from the ceiling and from the soap dish wall to the center of the tub spout Record your measurements Image C AT Step 4 Transfer your measurements onto the new sheet of acrylic Use a straight edge to connect the measurements Image D Q Tip If you are using simulated tile double check that the grout lines will match up Step 5 Cut the panel slowly carefully supporting your panel with your other hand and keeping your fingers clear from the blade Image E Step 6 Use a 1 hole saw to cut out holes for all three hardware openings Tip The mixer valve hole will probably need to be enlarged Use a jigsaw to enlarge the hole for the mixer valve making it large enough to get at the screws but not bigger than the valve cover Image F Step 7 Test fit your panel Make sure that your plumbing holes line up and trim as needed Step 8 Wipe down the existing wall with denatured alcohol Tap any excess primer off your brush and into the can so it does not drip then apply it around the p
12. STALLATION Step 1 Dremmel out the drain hole be sure not to touch the acrylic Image J Step 2 Insert the turnbuckle into the pipe and tighten securely Step 3 Screw the adapter plate into the existing base with a flat head screwdriver Image K Step 4 Screw the cover on top of the adapter with an allen wrench Image L CROSSBAR DRAIN INSTALATION Step 5 If you are installing this drain on a flat liner you will have already installed the crossbar under the liner If installing on a liner with a dimpled recess place the crossbar on the recessed area Image M Step 6 Place the drain cap over drain hole Step 7 Secure in place with supplied screw using a flathead screwdriver Image N www ellasbubbles com Page 8 08 14 e Q Shower Bases ACCESSIBLE BATHROOMS SNAP IN DRAIN INSTALLATION Step 1 Place the cover on the drain and trace the perimeter Use a dremmel to cut out the hole then remove the rag from the drain Image P Step 2 Snap the drain into place Image Q www ellasoubbles com Page 9 08 14 e Q Shower Bases ACCESSIBLE BATHROOMS SHOWER PAN INSTALLATION TOOLS A Pipe Wrench 4 Notepad Aa Hammer or Sledge A Tape Measure A Pry Bar 4 Drop Cloths A Spud Wrench A Utility Knife A Sharpie Marker Step 1 Remove all hardware including the drain cover Image HH Step 2 Stuff a rag into the drain to keep debris from entering Step 3 Measure the drain center from the soap d
13. YSTAL DRAIN CLEANERS e GREENWORKS BATHROOM CLEANER e SCRUB FREE W BLEACH e SEVENTH GENERATION BATHROOM CLEANER REGULAR e MAGIC ERASER www ellasbubbles com Page 35 08 14 eljo ACCESSIBLE BATHROOMS Installation Tools amp Supplies Checklist Installation Below is a list of suggested tools and supplies for installing Ella Acrylic products Standard Tools REQUIRED Tape Measure 3 4 width Safety goggles knee pads amp elastic back support belt Levels 24 48 72 Dremmel Tool or Roto Zip Tool 25 and 50 Extension Cords Heavy Duty Caulk Gun Orbital Jigsaw w 10 TPI blades Drill bits metal and masonry Wall anchors and Non corrosive Screws 3 8 Electric Drill Cordless Drill 18V 1 5 8 and 3 Screws Utility Knife Channel Locks Pipe Wrench DOU OU UDO O U UUU OU DU U L Sawzall www ellasbubbles com DOO OUO O OU UOU U OU DU L 60 Metal Ruler Hammer Pliers Allen Wrenches Hole Saw Kit Screw drivers Crescent Wrench Teflon Tape 1 1 2 dia Die cast amp plastic slip joints amp washers 1 4 X 20 Drill amp Tap Combo amp Handle Steel Rafter Square 16 x24 Pipe cutters good quality Thread Compound Tub Drain Shoe Gaskets Page 36 DOOU OUUU OU OU OUUU OU OU DU L SUGGESTED Wire Brush or Paint Scraper Handle Puller Nail Punch Set Chisel Hack saw Duct Tape File Roto Zip Bits for wood plastic amp siding Co
14. aight edge Image N Step 7 Mark the bullnose edge using the bullnose line guide Locate the appropriate measurement for your bullnose edge Place your Sharpie marker into the appropriate hole and slide the bullnose line guide along the bullnose edge BACK WALL LEVEL MEASURE There are two measuring options the template method and the level method The following is the level method Please refer to page 44 for the back wall template method Step 1 Draw a level horizontal line across the back wall from soap dish wall to outside edge of back wall Image P Step 2 Measure from the horizontal line up to the ceiling in three different locations to determine if the ceiling is level Record the measurements on the existing wall Image Q Note If your ceiling is not level cut the top edge of the wall panel according to the difference in your measurements Step 3 Measure from the top of the tub or shower base up to your horizontal level line in 3 different locations Add these measurements to your measure ments from the level line to the ceiling and record them on the existing wall Image R www ellasbubbles com Page 26 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS BACK WALL INSTALLATION CONTINUED BACK WALL TEMPLATE MEASURE CONTINUED Step 4 Measure from the top of the tub or shower base down to the floor for the leg measurement Record your measurement Image S Step 5 Measure from the edge of the ba
15. any accessories Step 2 Make sure the bathroom is dust free Step 3 Use silicone primer on all seams before applying silicone Image A Step 4 Check that wall panels and accessories are pressed firmly into place and have not moved or lifted Step 5 Seal the perimeter of the liner and accessories and fill in all gaps Image B Step 6 Using a caulk finishing tool to clean off any excess silicone and smooth with your fingertip Image C Q Tip It s best to do a small area at a time so the silicone does not start to skin over www ellasbubbles com Page 34 08 14 e Q Product Information ACCESSIBLE BATHROOMS RECOMMENDED ACRYLIC CLEANERS Use only cleaning products whose labels state that they are SAFE FOR ACRYLIC Always test products on a small area of skirt before applying to complete bath area e SCRUB FREE e FORMULA 409 e BATHROOM DUCK e SCRUB FREE W OXY LEMON SCENT e ZEP SHOWER TUB amp TILE e GREENWORKS NATURAL ALL PURPOSE CLEANER e KABOOM SHOWER TUB amp TILE CLEANER e SEVENTH GENERATION SHOWER CLEANER NATURAL CITRUS DO NOT USE the following on your ACRYLIC Bath System The use of the following chemicals will cause a dull surface or chemical cracks The use of these products will VOID YOUR WARRANTY e DOW SCRUBBING BUBBLES e ABRASIVE CLEANERS e AJAX e COMET e FANITISTIK e TILEX e SOFT SCRUB e MR CLEAN e NAIL POLISH REMOVER e SCOURING PADS e AMMONIA e TOUGH ACT e POWDER OR CR
16. ate method and the level method The following is the template method Please refer to page 45 for the back wall level method Step 1 Using the large wall template place the template on the back wall with the long edge against the soap dish wall and the short sides tight against the ceiling and top of tub or shower base Image J Step 2 Check for any gaps due to bowed walls or other miscellaneous reasons and adjust accordingly Once you have set the angles tighten the lock knobs and remove the template Q Tip Be extremely careful not to bump the template once you ve set your angles If you do you will need to go back and re template Step 3 Measure from the soap dish wall side out to the location where the bullnose edge or tri guard will end In most cases this location should be at least 1 4 past the end of the existing tile Image K Step 4 Make sure that back wall bullnose edge matches up to the bullnose edge on the ceiling Image L www ellasbubbles com e Q Wall Surrounds ACCESSIBLE BATHROOMS BACK WALL INSTALLATION CONTINUED BACK WALL TEMPLATE MEASURE CONTINUED Step 5 Mark these measurements on your wall panel and connect the marks using a straight edge Image M Step 6 Place the wall template onto the new wall panel flush with the top ceiling edge Hold the template up to this depth line to mark the top and bottom angles of the back wall Remove the template and connect the marks using a str
17. ck wall to the outside of the tub to get the width of the leg Make sure to account for the radius of the tub Record these measurements on the existing wall Image T Step 6 Check to make sure the tub skirt or shower base is plumb using a small level Image U Tip If your leg is less than 2 it may tend to bow out during the test fit There are two ways you can fix this OPTION 1 If you have removed the floor trim and the panel comes to the floor when you reinstall the trim it can be used to support the leg against the tub Image S left OPTION 2 Drill a pilot hole and use a small finishing nail to secure the panel tight against the tub The nail should be placed close enough to the tub so it will be hidden by the liner once installed or when sealed with silicone Image S right Step 7 Draw a vertical plumb line from the ceiling to the top of the tub Measure from the vertical line to the soap dish wall corner reinforcement in three locations to determine if the wall is plumb Record these measurements on the existing wall Image W Step 8 Measure from the soap dish wall out to the location where you want the bullnose edge or tri guard to end Record your measurements Image X f s f dhe fo oe oe l ee LA ii Finishing tail pei Option 2 i i lei dell ATI at be dei d hy TA K ed gd de A E se x EN p www ellasoubbles com Page 27 08 14 e Q Wal
18. cord the measurements Image J Step 2 Transfer measurements to the inside corner trim and cut with tin snips Test fit the piece and trim if necessary Image K Step 3 Apply the butyl tape on the inside corner trim just like the outside corner trim Apply tape to both sides of the inside corner trim and push into place Image L www ellasoubbles com Page 31 08 14 e Q Wainscoting ACCESSIBLE BATHROOMS WAINSCOTING INSTALLATION CONTINUED SEAM TRIM INSTALLATION Tip Seam trim covers the seam of two pieces of wainscoting that meet in the middle of a wall Step 1 Measure the height from top of wainscoting to floor and add 1 8 for material Image M Measure the depth adding 1 8 for material Record the measurements Step 2 Transfer measurements to the seam trim Cut the seam trim then test fit and trim accordingly Step 3 Apply butyl tape to seam trim and push into place Image N FINAL SEAL Step 1 Wipe down panels and apply silicone primer to all seams Step 2 Apply color matched silicone sealant to all seams Image O www ellasbubbles com Page 32 08 14 www ellasbubbles com ejo ACCESSIBLE BATHROOMS Installation Final Silicone Adhesive Seal Page 33 08 14 e Q Final Silicone Adhesive Seal ACCESSIBLE BATHROOMS TOOLS 4 Color matching Silicone a Rag Paper Towels Q Silicone Primer Q Caulk Finishing Tool Step 1 Wipe down all the walls and the liner as well as
19. d which is the soap dish wall and mark accordingly Transfer the depth marks on the panel measuring back from the bullnose edge to the soap dish wall side Tip The measurements will be reversed when they are transferred to the ceiling panel The sheeted side where the markings are made will actually be the new ceiling surface when installed Be sure that you accurately identify which end of the panel is your plumbing wall and mark it appropriately Step 6 Connect depth marks with a straight edge Place the template on the panel Use the template to trace the angle onto the acrylic ceiling panel Db Tip Be extremely careful not to bump the template once you have set your angles If you do you will need to go back and re template Step 7 Hold the template up to your depth line and mark the plumbing wall angle Remove the template and connect the marks using a straight edge Step 8 When measuring to get the width use the plumbing wall template line as a starting point and create the opposite wall line Double check your measurements G H Plumbing Plumbing Plumbing Wal Side Soap Dish Wall Side Wall ae Soap Dish Wall Side dh i Soap Dish Wall Side 2 T E Bullnose Edge Bullnose Edge Bullnose Edge www ellasbubbles com Page 15 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS CEILING PANEL INSTALLATION CONTINUED Step 9 Mark the bullnose edge using the bullnose line guide The bullnose line guide is pr
20. e a continuous bead of silicone around the perimeter between the round tape and the wall and around the drain of the existing base Image SS Step 17 Insert the pan liner then walk up and down the perimeter to ensure proper contact Wipe off any excess silicone Step 18 Install the new drain Refer to page 22 for proper instructions Step 19 Once drain is installed use silicone primer along the perimeter of the pan liner followed by a color matching silicone www ellasoubbles com Page 11 08 14 ejo ACCESSIBLE BATHROOMS Installation Wall Surrounds www ellasoubbles com Page 13 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS TOOLS 4 Orbital Jigsaw with Bosch T101 Blade 3 Notepad 4 Vacuum or 10 to 12 Tooth per inch Wood Blade 4 Tape Measure 4 Broom and Dust Pan a Level 4 Hammer 4 Garbage Bags 3 Screwdriver A Chisel A Drywall and Screws 3 Suction Cup 4 Pipe Wrench A Pliers 4 Large and Small Wall Templates 4 Handle Puller 3 Tub Template A Utility Knife 4 Work Table 4 Drop Cloths 3 Sharpie Marker 3 Extension Cords Q Tip Itis recommended to install the wall surrounds first and then the bathliner If you wish to install the bathliner first please refer to page 11 for proper instructions SEQUENCE OF INSTALLATION Wall prep first then install the ceiling panel then the soap dish wall Next step is the two side walls and then the bathliner WALL PREP d Tip If you need to replace the mixer valve check
21. e bathtub using a safety scraper Image C www ellasbubbles com Page 14 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS CEILING PANEL INSTALLATION Step 1 Measure the depth from the soap dish wall to where the new ceiling panel will end in three separate locations Image D Step 2 Measure the width from the back wall to the plumbing wall in three separate locations Image E Step 3 Place the small wall template flush against the ceiling with the long edge against the soap dish wall This will measure the angles Image F Step 4 Adjust the template accordingly to find the angles for both sides of the ceiling that touch the walls Note any gaps due to bowed walls or other miscellaneous reasons and adjust accordingly Once you have the correct angle tighten the lock knobs and remove the template Q Tip Keep the clear or blue plastic slip sheeting on all the panels throughout the installation and make marks and cuts with it on This will help keep the panel from becoming scratched or damaged Q Tip In normal weather conditions allow a 1 8 gap on all sides for standard expansion and contraction This can be achieved by simply cutting off your reference lines during the cutting process In extreme temperatures the acrylic material may expand or contract up to 14 Allow around 20 minutes for the material to adjust to the climate conditions inside the house Step 5 Identify which end of your panel is the plumbing wall an
22. e line Step 11 Measure and mark the height of the threshold in 3 or 4 different locations Connect the markings with a straight edge Image NN Step 12 Using an orbital jigsaw carefully cut the liner supporting the liner with your other hand and keeping your fingers away from the blade Step 13 Test fit the liner and trim as necessary Now is the time to check the fit to the existing pan and see if you will need additional layers of tape Q Tip Itis okay if there is a tiny gap between the pan liner and existing walls The walls can be built out to cover the gap Q Tip If you intend to use a turn buckle or crossbar drain on a flat pan liner you will need to install the adapter plate before you begin to install the liner If your pan liner has a dimpled recess you can install the adapter plate after the liner is installed Step 14 Install the liner by placing butyl primer along the bottom of the acrylic liner keeping away from the drain area and the rail of the threshold Image OO Then prime the rail and the bottom of the existing base again keeping away from the drain area Image PP Step 15 Place flat tape on top of the primer setting it paper to paper Layer the tape as needed to ensure proper contact Pull the release paper and double up tape along the perimeter Remove the release paper Image QQ Step 16 Place round tape along the shelf of the existing base 1 2 away from the wall Image RR Remove the release paper Plac
23. e marked with holes at 1 8 increments for ease of measuring Locate the appropriate measurement for your bullnose edge For example if you are cutting your bullnose edge at 1 4 then locate the 1 4 hole Step 10 Place the Sharpie marker into the appropriate hole and slide the bullnose line guide along the bullnose edge Image J CD Tip If there is no tile on the original ceiling cut the bullnose edge at 14 This allows room for 1 g of acrylic or wall material and 1 g of tape and adhesive Step 11 Cut the acrylic according to the measurements Cut the panel slowly carefully supporting the panel with your other hand and keeping your fingers clear from the blade Clean up your scraps as you go Image K Tip Make sure your jigsaw is properly prepared See page 9 for instructions Step 12 Wipe off panel with a terrycloth towel Test fit the panel and mark any areas that may need to be trimmed Q Ti p Use suction cups to stabilize the panels when test fitting and installing Step 13 Trim any areas according to the new markings Test fit again Continue trimming and re test fitting as needed Step 14 Once the ceiling fits wipe down the existing ceiling with denatured alcohol Q Ti p Always use drop cloths to avoid spilling Step 15 Make reference lines around the ceiling about 1 2 inside the perimeter Tap any excess primer off the brush and into the can so it does not drip then apply butyl primer around
24. e template once you have set your angles If you do you will need to go back and re template www ellasbubbles com e Q Wall Surrounds ACCESSIBLE BATHROOMS SOAP DISH WALL INSTALLATION CONTINUED Step 5 Connect markings with a straight edge Step 6 Measure from the plumbing wall to back wall and record the measurements Image S Transfer these measurements by making three width marks on the panel using the plumbing wall line as the starting point Step 7 Connect the lines with a straight edge Image T This will be the back wall Q When your project includes simulated tile walls you will need to take some additional time to pre plan before cutting to ensure your grout lines will match up on all three panels This can be done by taking accurate measurements of your soap dish wall and preliminary measurements of your plumbing and back walls You always want to be sure the full tile is at the top and equal spacing of tiles are on the left and right Plumbing Wall Side SOAP DISH WALL LEVEL MEASURE OPTION D There are two measuring options the template method and the level method The following is the level method Please refer to page 36 for template method Step 1 Draw a level horizontal line across the soap dish wall from plumbing wall to back wall Measure from the horizontal line up to the ceiling in three different locations to determine if the ceiling is level Record the meas
25. ejo ACCESSIBLE BATHROOMS Acrylic Wall Liner Installation Manual Standard www ellasbubbles com Page 08 14 eljo ACCESSIBLE BATHROOMS Jigsaw PIEPD iecreereee renne MEn Mi 6 Shower BASES cccccescccceecse ie ccsccsccescceccesces Rici e Wall SUFTOUNAS a RZ 14 WINSCOTING gii a n Moena 30 Final Silicone Adhesive SEegl IMM zie 34 Product InformatioNi Mia 38 Installation Tools amp Supplies Checklist 36 Corner Seat Installation NBR NER ccc ec cece escent ees 38 WOITOIBIV MIP7 MM i 45 Warranty Activation FOI eee 4 www ellasbubbles com Page 3 08 14 eljo ACCESSIBLE BATHROOMS Suggested Tool List J Bathtub Liner Template J Expandable Spud Wrench with 1 Combination Wrench J Drain Extractor I Drain Identification Kit I 1 1 2 dia Tub Drain Shoes Brass and PVC J 1 1 2 dia Die Cast amp Plastic Slip Joint Nuts amp Washers J Tub Drain Shoe Gaskets LJ Tub Overflow Gaskets beveled and flat I 1 1 2 dia Plumb Quick Rubber Couplings or Boots LJ Drain Snake hand operated J Plumber s Putty J Butyl Primer Can and Brush J Orbital Jigsaw with 6 TPI Blades J Sawsall L Compound Miter Saw I Safety Goggles Knee Pads and Elastic Back Support Belt I 3 8 Electric Drill Cordless 18V L Dremmel Tool or Roto Zip Tool J Roto Zip Bits for Wood Plastic and Siding J Heat Gun I Screwdrivers
26. erimeter and from side to side in lines approximately 5 to 9 inches apart Keep primer inch away from the edge Step 9 Make sure the primer is dry to the touch and apply the butyl tape on top of the primed areas Be sure to press firmly when installing so the butyl tape does not pull up when you remove the release paper www ellasbubbles com Page 24 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS PLUMBING WALL INSTALLATION CONTINUED Step 10 Remove the release paper Apply the silicone in between the butyl tape in a Z pattern keeping the bead about 1 4 thick Image G Step 11 Clean the back of the new panel with denatured alcohol or damp cloth Press the panel firmly into place Remove the slip sheeting and wipe down the panel to ensure it s secured Step 12 Attach the plumbing fixtures with Teflon tape Image H Step 13 Use silicone to fill in the gaps before the escutcheon plates are affixed Seal behind and around the fixtures Image I BACK WALL INSTALLATION BULLNOSE EDGE FINISHES There are three options for finishing the ends of your side walls Option 1 the bullnose edge Option 2 the use of a tri guard under the wall panel or Option 3 the use of a tri guard over the wall panel You should finish the edge as you did when installing the plumbing wall See pages 39 and 40 for directions on the three finishing options BACK WALL TEMPLATE MEASURE There are two measuring options the templ
27. ews 2 and 2 1 2 I Propane Cylinder Solder and Flux J Fire Extinguisher I Hand Truck 3 thick Sheet Rock J Hammer J Tape Measure 3 4 width LJ Duct Tape I 24 x36 Wall Shield I Paper Towels _I WD 40 I Garbage Can amp Bags J Lava Hand Cleaner 08 14 ejo ACCESSIBLE BATHROOMS Installation Orbital Jigsaw Prep www ellasoubbles com Page 5 08 14 e Q Orbital Jigsaw Prep ACCESSIBLE BATHROOMS Step 1 Measure the length of the bottom of the orbital jigsaw Add 1 to your measurement Step 2 Cut Velcro according to your measurements Q Tip Velcro is recommended Step 3 Place the Velcro on the bottom of the orbital jigsaw leaving excess Velcro hanging off each end Step 4 Wrap the excess Velcro around both edges of the jigsaw Image A Step 5 Press firmly and do the same to the other side Image B Step 6 Before cutting make sure you are wearing your safety glasses and your orbital setting is on high www ellasoubbles com Page 6 08 14 ejo ACCESSIBLE BATHROOMS Installation Shower Bases www ellasoubbles com Page 7 08 14 e Q Shower Bases ACCESSIBLE BATHROOMS dd Tip If you intend to use turnbuckle or crossbar drain on a flat pan liner you will need to install the adapter plate before you begin to install the liner If your pan liner has a dimpled recess you can install the adapter plate after the liner is installed TURNBUCKLE DRAIN IN
28. ge on the ceiling Step 5 Mark these measurements on your wall panel and connect the marks using a straight edge Image QQ Step 6 Place the wall template onto the new wall panel flush with the top ceiling edge Hold the template up to this depth line to mark the top and bottom angles of the plumbing wall Remove the template and connect the marks using a straight edge Image RR Step 7 Mark the bullnose edge using the bullnose line guide Locate the appropriate measurement for your bullnose edge Place your Sharpie marker into the appropriate hole and slide the bullnose line guide along the bullnose edge Image SS www ellasbubbles com Page 22 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS PLUMBING WALL INSTALLATION CONTINUED PLUMBING WALL LEVEL MEASURE OPTION There are two measuring options the template method and the level method The following is the level method Please refer to page 41 for template method Step 1 Draw a level horizontal line across the plumbing wall from soap dish wall to outside edge of plumbing wall Image TT Step 2 Measure from the horizontal line up to the ceiling in three different locations to determine if the ceiling is level Record the measurements on the existing wall Image UU Note If your ceiling is not level cut the top edge of the wall panel according to the difference in your measurements Step 3 Measure from the top of the tub or shower base up to your horizontal
29. ing to ensure your grout lines will match up on all three panels This can be done by taking accurate measurements of your soap dish wall and preliminary measurements of your plumbing and back walls You always want to be sure the full tile is at the top and equal spacing of tiles are on the left and right SOAP DISH WALL INSTALLATION CONTINUED Step 6 Cut the wall panel slowly carefully support the panel with your other hand and keeping your fingers clear from the blade Clean up scraps as you go Image Z Step 7 Test fit the panel and mark necessary adjustments Image AA Use suction cups to assist in handling the panel during the test fit and installation Q Ti p Be real careful with larger panels while walking through the customers home T Tip If using simulated tile the suction cups will not adhere to the panel Instead you can pull down a section of the plastic slip sheeting to create handles and use those to help put the wall in place Image BB Step 8 Continue to measure trim and test fit until you have a desired fit Step 9 Wipe down the existing wall with denatured alcohol Tap any excess primer off your brush and into the can so it does not drip then apply it around the perimeter staying 1 2 away from the edge and from side to side in lines approximately 5 to 9 inches apart www ellasbubbles com Page 19 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS SOAP DISH WALL INSTALLATION
30. ish wall to the center of the drain and again from the plumbing wall to the center of the drain Record the measurements Image II Step 4 Use the small wall template to get the angles of the existing shower Place the template in the corner of the existing base with one end against the soap dish wall and the other end against the plumbing wall Set the template to fit and tighten the lock knobs Image JJ Step 5 Carefully remove the template from the shower base Do not bump the template If you do you will need to go back and re template Step 6 Measure the height of the threshold by holding a straight edge out from the top of the rail measure from the floor to the straight edge in 3 or 4 locations Image KK Step 7 Add 3 8 to your height measurements for thickness of acrylic material and adhesives Record the measurements Step 8 Transfer measurements To mark the drain center place a straight edge in the drain area Measure from the drain center to the soap dish wall and mark your measurements Then measure from the drain center to the plumbing wall and mark your measurement Image LL Step 9 Place the template along the marks and trace the outside of the template Image MM www ellasbubbles com Page 10 08 14 e Q Shower Bases ACCESSIBLE BATHROOMS SHOWER LINER INSTALLATION CONTINUED Step 10 Measure and mark the length of the liner using the width line as a starting point Use a straight edge to extend th
31. l Surrounds ACCESSIBLE BATHROOMS BACK WALL INSTALLATION CONTINUED Step 1 Transfer your measurements onto the new sheet of acrylic Image AA Use a straight edge to connect the measurements Tip If you are using simulated tile double check that the grout lines will match up Step 2 Cut the panel slowly carefully supporting your panel with your other hand and keeping your fingers clear from the blade Image BB Step 3 Test fit your panel and trim as needed Image CC Step 4 Wipe down the existing wall with denatured alcohol Tap any excess primer off your brush and into the can so it does not drip then apply it around the perimeter and from side to side in lines approximately 5 to 9 inches apart Keep primer 1 2 away from the edge Image DD Step 5 Make sure the primer is dry to the touch and apply the butyl tape on top of the primed areas Be sure to press firmly when installing so the butyl tape does not pull up when you remove the release paper Step 6 Remove the release paper from the butyl tape Apply the silicone in between the butyl tape in a Z pattern keeping the bead about 1 4 thick Image EE Step 7 Clean the back of the new panel with denatured alcohol or damp cloth Press the panel firmly into place Remove the slip sheeting and wipe down the panel to ensure it is secured Image FF www ellasbubbles com Page 28 08 14 ejo ACCESSIBLE BATHROOMS Installation Wainscoting www el
32. lace or provide a refund whichever Ella s Bubbles LLC deems appropriate This warranty is in lieu of all warranties expressed or implied and is in fact the only warranty in regard to walls surrounds offered by Ella s Bubbles LLC In any event Ella s Bubbles LLC shall be responsible only for repairs replacement of tub liners or wall systems or a refund not to exceed the total amount paid for the tubliners or wall systems originally and will in no way be liable for any losses time expenses attorney s fees inconvenience and or incidental or consequential damages The residential buyer specifically waives the warranty for fitness for a particular purpose All mailing notification must be sent via certified mail to Ella s Bubbles LLC 2101 S Carpenter Street Chicago IL 60608 Email info ellasbubbles com TOLL FREE 800 480 6850 l C Warranty Activation Form ACCESSIBLE BATHROOMS INSTALLER S INFORMATION Name Address City State Zip Telephone gt Email Date Signature Upon completing the installation of an Ella Walk In Tub the following Warranty Activation Form must be completed signed by both the customer and installer and returned to Ella s Bubbles LLC In order for the Warranty to be activated faxed scanned or emailed or hard copy mailed To be initialed by the installer s Tub is level in all directions and all support legs are touching the ground Tub is installed on a dedicated 30 Amp
33. lasoubbles com Page 29 08 14 e Q Wainscoting ACCESSIBLE BATHROOMS TOOLS 3 Tin Snips _1 Tape Measure Q Straight Edge A Orbital Jigsaw 3 Sharpie Marker WAINSCOTING INSTALLATION Step 1 Ask the customer how high up the wall they want the wainscoting to end Image A Tip Height cannot pass 59 Step 2 Draw a level horizontal line across the wall 1 below the desired location Image B a Tip If there is existing tile on the wall and the top of the existing tile is level you can use that as your horizontal line Step 3 Measure down from the horizontal line to the floor in 3 or 4 different locations Add 1 to the measurements Image C Record the measurements Step 4 Draw a level vertical line from your horizontal line to the floor Measure from the vertical line to one end of the wall in 3 or 4 different locations Record the measurements Image D Step 5 Cut the panel carefully supporting the panel with your other hand while keeping your fingers clear from the blade Keep slip sheet on to prevent any scrapes or scratches Step 6 Test fit the panel and make necessary adjustments Step 7 Prime along the border of the existing wall staying 2 away from the edge Place primer in vertical lines approximately 9 apart Image E Step 8 Allow primer to dry Cover the primer with butyl tape and remove the release paper Place silicone sealant between the lines in a Z pattern Image F
34. level line in 3 different locations Add these measurements to your measure ments from the level line to the ceiling and record them on the existing wall Image VV ye e A Step 4 Measure from the top of the tub or shower base down to the floor for the leg measurement Record your measurement Image WW Step 5 Measure from the edge of the plumbing wall to the outside of the tub to get the width of the leg Make sure to account for the radius of the tub Record these measurements on the existing wall Q Tip If your leg is less than 2 it may tend to bow out during the test fit There are two ways you can fix this OPTION 1 If you have removed the floor trim and the panel comes to the floor when you reinstall the trim it can be used to support the leg against the tub Image XX left OPTION 2 Drill a pilot hole and use a small finishing nail to secure the panel tight against the tub The nail should be placed close enough to the tub so it will be hidden by the liner once installed or when sealed with silicone Image XX right Step 6 Check to make sure the tub skirt or shower base is plumb using a small level Step 7 Draw a vertical plumb line from the ceiling to the top of the tub or shower base Measure from the vertical line to the soap dish wall corner reinforcement in three locations to determine if the wall is plumb Record these measurements on the existing wall Finishing www ellasbubbles com
35. mpound Miter Saw Stud Finder Adjustable Slip Nut Wrench Roto Zip bits for wood plastic amp siding 3 Ib Sledge Hammer Drain Snake hand operated 08 14 e Q Installation ACCESSIBLE BATHROOMS Installation Tools amp Supplies Checklist Installation Tools cont Other Tools Items SUGGESTED Drop Light w 6 cord or Folding Saw horses 1 sheet flashlight 4 x8 x3 4 plywood cutting table Shop Vac Magnetic Drive Guide Heat Gun 1 2 Thick Green Board Sheet Rock 24 X 36 Wall Shield scrap Propane cylinder Solder amp Flux piece of acrylic to protect wall Tool Box or 5 Gallon Pail when installing Bathliner Fire Extinguisher 3 8 Studs Drop cloths Sealant Finisher Wonder Pry Bar SUGGESTED _ Broom amp Dust Pan _ Lava Hand cleaner Sharpie Marker Razor Blades E Q tips _ First aid kit E E Soft clean rags Denatured Alcohol WD 40 Garbage Can or Trash Bags Paper Towels Bounty Select A Size www ellasoubbles com Page 37 08 14 e Q Installation ACCESSIBLE BATHROOMS CORNER SHOWER SEAT INSTALLATION Follow the steps below when installing a Ella Acrylic Corner Shower Seat i NOTE The Shower Base is installed before i the Corner Shower Seat The Wall i Surrounds are installed after the Corner Shower Seat 1 Shower Base installed 2 Corner Shower Seat installed I I I I I I I 3 Wall Sur
36. rement Image M Step 2 Transfer the measurement to the reinforcement Cut the reinforcement with tin snips Image N Step 3 Test fit the corner reinforcement Trim and re test fit as necessary Step 4 Once the reinforcement fits clean and prep the existing walls using industrial strength cleaner and denatured alcohol Step 5 Apply silicone on both sides of the inside corners of the wall in a continuous bead from ceiling to top of tub or shower base Press reinforcements into place Image O Q Tip Another continuous bead of silicone will be added on top of the corner reinforcements before final wall installation and after walls are in place SOAP DISH WALL TEMPLATE MEASURE OPTION There are two measuring options the template method and the level method The following is the template method Please refer to page 37 for level method Step 1 Using the large wall template place the long edge against the plumbing wall and the short sides against the ceiling and top of tub or shower base Image P Step 2 Check for any gaps due to bowed walls or any other miscellaneous reasons and adjust accordingly Step 3 Tighten the large lock knobs securely Image Q Step 4 Use the template to transfer the measurements onto the soap dish wall panel Place the template onto the new wall panel flush with the top ceiling edge and make three marks along all three sides of the template Image R Q Tip Be extremely careful not to bump th
37. rounds installed I Tools Supplies e 2 x4 s e Tape Measure e Drop cloths e Level e Broom dust pan e Dust mask e Drill e Garbage bags e Safety glasses gloves e Screwdrivers e Drywall e Jigsaw e Drywall screws e Sharpie Marker e Shims Initial Steps Install the Shower Base per instructions See Ella Installation Manual for more information Place cardboard in bottom of Shower Base for protection Check to make sure you have the right order for the right customer Double check the color of the Corner Shower Seat The Corner Seat is typically installed opposite of the plumbing es ye i E i CORNER SEAT DETAILS e Seat Area 16 x 16 e Corner Seat piece extends out 19 on both the left and right side Fig 1 e Can hold up to 300 pounds e Has been tested and approved by NAHB Research Center Fig 1 www ellasbubbles com Page 38 08 14 e Q Installation ACCESSIBLE BATHROOMS CORNER SHOWER SEAT INSTALLATION i Fig 2 Set Frame for Corner Shower Seat 1 Measure roughly 17 out from inside corner for outside edges of Corner Seat Fig 2 a This measurement may be different depending on the studs already in place 2 Atthe appropriate measurement add additional frame studs to inside wall area for seat as needed Fig 2 3 Add 2 x4 as needed for cross beams Initial Cutting The Corner Seat includes flanges and sprayfoam on the back for stability Fig 3
38. urements on the existing wall Image U Note If your ceiling is not level cut the top edge of the wall panel according to the difference in your measurements Step 2 Measure from the top of the shower base or tub up to the horizontal line in three different locations Add these measurements to the measure ments you took from the level line to the ceiling and record them on the existing wall Image V Step 3 Draw a vertical plumb line from the top of the shower base or tub to the ceiling Measure from the vertical line to the plumbing wall corner reinforce ments at 3 or 4 different locations to determine if the wall is plumb Record the measurements on the existing wall Image W www ellasoubbles com Page 18 08 14 e Q Wall Surrounds ACCESSIBLE BATHROOMS SOAP DISH WALL INSTALLATION CONTINUED SOAP DISH WALL LEVEL MEASURE OPTION CONTINUED Step 4 Measure from the plumbing wall to the back wall in the same 3 or 4 different locations you used to check if the wall was plumb Image X Tip Try to measure the walls using the same increments on both sides Step 5 Write all of your measurements on your notepad Transfer your measurements to your new wall panel and using a straight edge draw lines con necting the marks Image Y D Tip When your project includes simulated tile walls you will need to take some additional time to pre plan before cutt
39. y please complete both pages and use one of the options below to submit Via mail Via fax Via email Ella s Bubbles LLC Warranty Department 2101 S Carpenter St Chicago IL 60608 1 312 666 3551 warranty ellasbubbles com www ellasbubbles com Page 48 08 14
40. y into place Image MM Tip Buty tape can also be used to adhere the tri guard Step 4 When installation is complete you will apply a finishing bead of silicone along the tri guard Image NN Q Tip The tri guard comes in all color options as well as two different sizes See product catalog for details www ellasoubbles com Page 21 e Q Wall Surrounds ACCESSIBLE BATHROOMS PLUMBING WALL INSTALLATION CONTINUED PLUMBING WALL TEMPLATE MEASURE OPTION There are two measuring options the template method and the level method The following is the template method Please refer to page 42 for level method Step 1 Using the large wall template place the template on the plumbing wall with the long edge against the soap dish wall and the short sides tight against the ceiling and top of tub or shower base Image OO Step 2 Check for any gaps due to bowed walls or other miscellaneous reasons and adjust accordingly Once you have set the angles tighten the lock knobs and remove the template Q Tip Be extremely careful not to bump the template once you ve set your angles If you do you will need to go back and re template Step 3 Measure from the soap dish wall side out to the location where the bullnose edge or tri guard will end In most cases this location should be at least 1 4 past the end of the existing tile Image PP Step 4 Make sure that plumbing wall bullnose edge matches up to the bullnose ed
Download Pdf Manuals
Related Search