Coastal Shower Doors 6260.76B-C Instructions / Assembly
Contents
1. Towel Bar Screw 2 L6 Back Plate Cover e ees ee ee ee 2 L7 GON Al OE EE N 2 1 Measure the base opening along center of shower curb as shown in figure 1 then trim Sill A to measurement obtained 2 Trim the Vinyl Seal J to an inch and one eighth 1 1 8 less than the base opening Slide Vinyl Seal J into the Sill s re ceiver as shown in figure 2 and center it on the Sill MEASURE BASE OPENING 3 With high lip toward exterior of enclosure position Sill at figure 1 center of shower curb Temporarily tape Sill to shower curb to prevent movement 4 Place Wall Jambs B on to ends of Sill A and up against shower walls as shown in figure 3 Plumb the Jambs then pencil mark their installation holes locations on the shower walls 3 per jamb Remove Wall Jambs Using a 3 16 glass tile drill bit drill 1 deep installation holes in locations previously marked Insert Plastic Screw Anchors H into holes 5 Reposition Wall Jambs B as before and secure Jambs to shower walls using three 3 8112 Installation Screws G Make sure to attach Panel Bumpers F to top and bottom installations holes as shown in exploded view sheet 1 Please note that notches on bumpers are positioned so as to accept glass insertion as shown in figure 4 6 Measure the wall to wall opening at top of Wall Jambs and cut the Header C to the measurement2. ALL a A INSIDE PANEL S5 OUTSIDE PANEL ii n LOCATED TO ACCEPT GLASS figure 4 figure 5 figure 7
3. FAX NO 904 641 1697 P O BOX 16091 JACKSONVILLE FLORIDA 32245 Paragon 3 8 Frameless exploded view A KEY PART LETTER NUMBER DESCRIPTION A 651 CS ee rn eer IK B 643 WALL JAMB Cc 650 HEADER ou ceeeecesccscceeseeeseeeseeeceeesseeseeesees D GLASS PANEL ASSEMBLY ees ese di CP652C Hanger Bracket issie see ee d2 1 4 Flat Head Phillips Screw ees ee d3 PN3401 Nylon Roller iese ee ee ee ee Ee ee d4 832HEX Roller SCheWS ie EER KERE aa d5 Nylon Sleeve not Shown ese ee ee d6 8321875SS Nylon Set Screws not Shown Lees ee E 638PHPT 6 x 3 8 Self Drilling Phillips Screw F 5172B JAMB BUMPER iese sesse ese ee ee ee ee ee PARAGON 3 8 FRAMELESS BYPASS 04 20 18 Coastal Industries Inc TELEPHONE NO 904 642 3970 Se Ie Se KEY PART LETTER NUMBER DESCRIPTION QTY G 8112 INSTALLATION SCREWS cccccseeeees 6 H 1329 PLASTIC SCREW ANCHOR 000 6 C375G TRACK GUIDE ciscssssscsccsccsscscessscsescecasasteees 1 J C494B SILL SEAL VINYL ese esse see ee see ee ee ee 1 K designation not used ee eee L T24 TOWEL BAR ASSEMBLY 00008 2 L1 Towel Bar ee ties 1 L2 aoe Plastic Bushing 2 L3 o Plastic Spacer 4 L4 Back Plate 2 L5
4. led Locate center of Sill position the Track Guide on the Sill and using holes on Guide as templates secure Guide to the Sill using two 638phpt Self Drilling Screws E as shown in figure 6 10 Before beginning Towel Bar installation note that Towel Bars L1 are attached on the same side as the Nylon Rollers d3 as shown in the exploded view sheet 1 Install Towel Bars L see exploded view sheet 1 and figure 7 on this page Slip a Back Plate L4 a Plastic Spacer L3 and a Sleeve Bushing L2 onto a Towel Bar Screw L5 as shown in figure 7 Insert it into the glass hole as shown and attach one end of a the Towel Bar L1 to it do not forget Plastic Spacer L3 and Collar L7 Attach the other end of the Towel Bar onto the Glass Panel Tighten down on screws to secure Cover the screws by placing a Back Plate Cover L6 over the Back Plate L4 Repeat step for the remaining Towel Bar 11 Run a bead of clear mildew resistant caulking down the full length of each Wall Jamb outside where the Jambs meet the Walls Now run a bead outside where the Sill meets the curb Finally run a bead along the crevice where the Wall Jambs straddle the Sill see figure 3 Follow caulking manufacturer s instructions before using shower normally 24 hours Installation is now complete PARAGON 3 8 FRAMELESS BYPASS 04 20 18 INSERT SILL VINYL INTO RECEIVER figure 2 WALL JAMB STRADDLES SILL figure 3 SHOWER HEAD W
5. obtained Position and install the Header over the Wall Jambs 7 Attach Hanger Brackets as shown in exploded view sheet 1 and figure 5 this sheet Begin by inserting a Nylon Sleeve d5 into the glass panel holes Next screw in two Nylon Set Screws d6 onto the Hanger Bracket d1 as shown in figure 5 the purpose of nylon set screws is for leveling adjustment of hanger bracket so it will not see saw on glass adjust as required Position Hanger Bracket onto the Glass Panel and secure to glass using a 1 4 Phillips Flathead Screw d2 Finally install the Roller d3 as shown and secure with a Hex Screw d4 Repeat step for the remaining Hanger Brackets 8 Install the outside Glass Panel D by lifting the Panel up and into the Header B Lower the Panel into the Track Guide I and engage the Rollers d3 with the roller track Slide outside Door Panel into Wall Jamb located on wall opposite of shower head Check Panel to make sure that it is parallel to the Wall Jamb If it is not remove the Door Panel and adjust the rollers either up or down by loosening the Rollers Screws and sliding the Rollers When satisfied with outside Door Panel alignment proceed with inside Door Panel installation When satisfied slide inside Door Panel into Wall Jamb located on shower head wall and check for alignment with Wall Jamb Adjust Rollers as necessary 9 To insure proper operation Track Guide I must be centered on Sill A when instal
Download Pdf Manuals
Related Search