American Standard T028.900.295 Installation Guide
Contents
1. Installation Instructions TO28 900 Americam Standard DECK MOUNT TUB SYSTEMS DAZZLE TRIM KIT Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended Tools 3 Phillips Screwdriver 3 Flat Blade Screwdriver Drill with 3 16 bit SPOUT INSTALLATION E Complete FINISHED DECK before trim installation m Turn off the water supplies Remove the GUARDS 1 fram the VALVE BODIES 2 Remove the GUARD 3 and 1 4 PLUG 4 from the SPOUT SHANK 8 The SPOUT SHANK 5 height should be 1 to 2 above the FINISHED DECK Cut the SPOUT SHANK 5 if necessary Remove all burrs and bevel the end of the shank Failure to do so may damage the SPOUT O ring during installation and cause water leakage Drill a 3 16 hole in the finished deckfor spout locking pin See TEMPLATE for location gt a 8 4mm 21 64 E 3 16 DIA HOLE 19 pmm a 18 8mm DIA I I I I p 28732 47 64 y SPOUT SHANK I I I I I I TEMPLATE FOR y SPOUT ROLL FRONT PIN LOCATION 3 16 DRILLED HOLE a Certified to comply with ANSI A112 18 1 U S Patent No D403 750 M968495 Rev 1 2 Channel Locks djustable Wrench REMOVE ALL BURRS AN 1 A SPOUT INSTALLATION Lubricate th2. coLD Slowly turn on the water supplies 7 3 HANDLE Operate the HANDLES to flush water lines thoroughly Check SPOUT connection for leakage Turn the Handles off Replace the SPOUT END STREAM STRAIGHTENER 5 SERVICE To change the direction of handle rotation Turn off the water supplies Turn HANDLE 1 to the off position Unthread the HANDLE BASE 2 from HANDLE ADAPTER 3 Unthread HANDLE ADAPTER 3 and remove Remove VALVE LOCKNUT 4 A 17mm deep socket is required Remove the CARTRIDGE 5 by pulling up on the SLEEVE 6 Remove SCREW 7 and pull off SLEEVE 6 Remove the SPRING CLIP 8 Remove the STOP WASHER 9 Turn it 90 and replace Replace the SPRING CLIP 8 Reverse the above steps to reassembly the components lf the spout drips operate the handles several times from the off to the on position Do not force the handles only turn 90 CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968495 Rev 1 2
3. e SPOUT ADAPTER O RING 6 and SPOUT O RING 7 Push SPOUT ADAPTER 8 on SPOUT SHANK 5 and align slot in SPOUT ADAPTER 8 with 3 16 drilled hole Tighten SPOUT ADAPTER SET SCREW 9 securely with 4mm HEX KEY 10 supplied Position the RUBBER RING 14 in the groove in the base of the ESCUTCHEON 11 Push the SPOUT 12 with ESCUTCHEON 11 down onto the SPOUT ADAPTER 8 and tighten the SET SCREW 13 securely with the 5mm HEX KEY 15 supplied INSTALL HANDLE ADAPTERS Place the ESCUTCHEON SEALS 1 into groove of DECK ADAPTERS 2 Align the HANDLE STEM 3 with the SLEEVE 4 as necessary Thread the HANDLE ADAPTER 5 into the VALVE BODY 6 until the DECK ADAPTERS 2 contacts tight against the finished deck INSTALL HANDLES Push ADAPTER 1 on VALVE STEM 2 so that the hole of the ADAPTER 1 without a spline is facing up See figure A Tighten STEM SCREW 3 to secure ADAPTER 1 Find correct position of LEVER HANDLE ASSEMBLY 4 by adjusting male teeth on ADAPTER 1 to female teeth in HANDLE 4 Thread LEVER HANDLE ASSEMBLY 4 onto DECK ADAPTER 3 until THREAD ON snug against mounting surface Repeat steps for opposite handle Tock A ADAPTER i TOP Pag PLU errr LAN i DN p SPLINE END DOWN Figure A M968495 Rev 1 2 4 TESTING M Turn the HOT HANDLE clockwise and the COLD HANDLE counterclockwise to the off position Unscrew and remove the STREAM STRAIGHTENER
Download Pdf Manuals
Related Search