DreamLine DL-6714-01CL Installation Guide
Contents
1. 5 16 R Fig 5 5 Slide the Corner profile 10 over the aluminum vertical edge of the Return glass panel 09 Drill the holes into the aluminum profile on the Return glass panel using an 1 8 drill bit through the predrilled holes in the Corner profile Secure the Corner profile to the Return glass panel with the Round head screws ST4 2x10 04 Set this Return glass panel assembly aside 2 See fig 6 and 7 details Fig 6 FLEX Enclosure Rev 1 Ver 3 03 2014 Fig 7 6 Install the Handle 13 onto the Door assembly 02 Move 1 the Door assembly onto the Shower base and slide the Stationary glass side into the Wall profile 01 See Fig 8 and Fig 9 for details FLEX Enclosure Rev 1 Ver 3 03 2014 Fig 8 Fig 9 7 Slide the Return glass panel 09 assembly into the groove of the Return wall profile 11 See Fig 10 for details Fig 10 FLEX Enclosure Rev 1 Ver 3 03 2014 9 Extend width of the Door assembly 02 by stretching the top and bottom Expanding rails toward the Corner profile 102. DLTA0M4B ir iX DLT 1036481 36 x48 DLT 1036601 36 x60 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 Right Hand Drain Configuration W1 D1 DLT 1034482 34 x48 MODEL SPECIFICATION D1 in W1 in 6 DLT 1036482 36 x48 DLT 1036602 36 x60 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 10 Diagram of the Shower Base Cross Section Finished Wall ya board Shower Base OOOO Mortar Plaster 2 x4 Stud Drain 2 PVC Waste Pipe SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 11 Shower Base Installation Preparation 1 Ensure that the floor and the studs are at right angle Provide a 5 x5 opening the sub floor for the drain The 2 PVC waste pipe should extend above the surface of the sub floor according to the drain installation instructions and the height of the Shower base Refer to the product drawings in these installation instructions for the drain location See Fig 1 and Fig 2 for details SLIMLINE SHOWER Rev 3 5 07 2013 2 PVC Waste Pipe 5 x5 Opening See Product Chart for Drain Location Fig 1 x 2 PVC Waste Pipe 5 x5 Opening See Product Chart for Drain Location Fig 2 12 2 Install the shower drain NOT PROVIDED according to the drain installation manual supplied with the drain See Fig 3 for details 3 Place the tray into the designated position so that the Drai
3. OREAMLINE dream in style FLEX Shower Enclosure and Base Kit Shower Enclosure and Shower Base Kit Installation Instruction IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical d rawings manuals or any other details please refer to the support BathAuthority com_ web page STEP 1 Install Shower Base STEP 2 Install Shower Enclosure hower Enclosure Installation Instructions Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support gro at support BathAuthority com For more information on DreamLine Shower Enclosure please visit www BathAuthority com ream in siyle FLEX SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Mon
4. When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wired brushes SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 16 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Installation of DreamLine product by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professionals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DA
5. please ensure that the installation surface is level and solid and will be able to support the total weight of the unit Also make sure that the walls are plumb Depending on the type of unit you are installing some adjustments in leveling may be possible However irregular installation surface level or out of square conditions can result in serious problems for your installation Please note that some adjustments and drilling may be necessary Please protect all primary surfaces of the product during installation Never set your glass down directly onto a tile floor Always use a piece of wood or cardboard to protect the bottom edge and corners of the glass Tools Required E Tape Philips Ec Caulk Measure Pencil Screwdriver 1279 16 Level Gun Hammer 2 1 8 FLEX Enclosure Rev 1 Ver 3 03 2014 2 Detailed Diagram of Shower Enclosure Components 1 10 11 el ies Door packing List 01 Wallprofle 2 06 Decorative cover Wallanchor 8pcs 08 Bottom anti waterstip 1 _ 105 Round head screws 9742540 41 Return panel packing List Round head screw ST4 2x10 Corner profile 106 Decorative cover 26 11 Returnwallprofile lpc 109 Return glasspanel OO shower enclosure please use only one wall profile NOTE Unpack y
6. Insert Glass door side into the Corner profile NOTICE The maximum adjustable length of the Expanding rails is 4 1 2 See Fig 11 and Fig 12 for details FLEX Enclosure Rev 1 Ver 3 03 2014 L 11 9 Make sure the Door assembly 02 is fully extended inside the Wall profile 01 and the Corner profile 10 Adjust top and bottom Expanding rails to the same length Use a tape for See Fig 13 for details 10 Drill holes in top and bottom Expanding rails through the predrilled holes using an 1 8 drill bit ATTENTION Do not drill the Expanding rail throughout only the first layer Secure the Expanding rails using Round head screws ST4 2x10 04 with the raised white washers Cover exposed screw heads with Decorative covers 06 See Fig 14 for details FLEX Enclosure Rev 1 Ver 3 03 2014 LE 12 Do the final adjustments to the Door assembly 02 and Return glass panel 09 if required Open and close the Glass door to make sure that the magnetic strips are fully attracted to each other Drill holes into the aluminum profile of the Door ass
7. any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period of one 1 year from initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one
8. 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS DreamLine warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THIS WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of special incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such a photos may be required to fully process your warranty claim 4 Proof o
9. Glass MASS RET Attach both pieces of the Bottom Anti water strip to the 2 bottom edge the Glass door gt See Fig 17 for details 14 Apply the silicone along the connection edges of the Wall profile 01 Return wall profile 11 bottom Expanding rail and the base of the Return glass panel 09 from both inside and outside the shower oon EE 2 Ou Waterproof gt Silicone 7 FLEX Enclosure Rev 1 3 03 2014 Product Maintenance To ensure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To ensure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe off the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scouring agents as this may scratch the surface Never use bristle brushes or abrasive sponges To ensure a long lasting hardware finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the sur
10. MAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHOWER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays DreamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or implied including but not limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its election repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repa
11. day through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Enclosure please visit www BathAuthority com Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or is missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns If this unit is going to be installed in a new construction please install all of the required plumbing and drainage before installing the shower Use a competent and licensed if required by local code plumber for all plumbing installation period Prior to installation
12. e Install the cement board or the wallboard above the tile flanges and secure it to the studs Put the tiles or other finishing material over the cement board leaving 1 8 gap between the bottom of the tile and the Caulk Ceramic Tile splash rim of the shower base Use caulk to fill that gap See Fig 8 and Fig 9 for details SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 15 Product maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To insure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To assure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week
13. embly through the predrilled holes in the Wall profile 01 using an 1 8 drill bit Drill holes into the aluminum profile of the Return glass panel through the predrilled holes in the Return wall profile 11 using an O 1 8 drill bit ATTENTION Do not drill the profiles throughout only the first layer Secure the Door assembly and the Return glass panel inside the Wall profile and Return wall profile using the Round head screws ST4 2x10 04 with the raised white washers Cover the exposed screw heads with the Decorative covers 06 See Fig 15 for details Drill holes into the aluminum profile of the Door assembly 1 02 through the predrilled holes in the Corner profile 10 using 1 8 drill bit Secure the Door assembly inside the Corner profile using the Round head screws ST4 2x10 04 with the raised white washers Cover the exposed screw heads with the Decorative covers 06 See Fig 16 for details FLEX Enclosure Rev 1 Ver 3 03 2014 1 8 ss Fig 16 13 Attach Flanged Anti water strip III 1 07 to the vertical edge of the Ris Stationary glass Dr Cut Bottom Anti water strip Outside 08 in two pieces to cover the BM RS bottom edge of the door from A lt Rh pivot to both sides of the
14. f purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com dream in style TEL 866 731 2244 FAX 866 227 1533 WWW BATHAUTHORITY COM For more information on DreamLine Shower Doors please visit www BathAuthority com
15. face as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not against the grain Never use an abrasive sponge or cloth steel wool or wired brushes FLEX Enclosure Rev 1 Ver 3 03 2014 14 OREAMLINE ream in style SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Bases please visit www BathAuthority com Preparation 1 boxes packages for shipping damage Carefully remove Shower base from the packaging and check for any visual defects or shipping damages If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department with
16. in 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions Install all of the required plumbing and drainage before installing the shower Use a competent and licensed if required by local code plumber for all plumbing installation Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project Please insure that prior to the installation the installation surface is leveled and solid and will be able to support the total weight of the unit Also make sure the walls are at right angles While some adjustment in leveling of the tray is possible irregular installation surface level or improper angle of side walls will result in serious problems for your installation Please note that some adjustments and drilling might be necessary during the installation process IMPORTANT NOTE Dimensions provided for reference only You must measure the actual shower tray sizes before installation Allowed tolerance for center of the drain is 1 2 Tools Required Tape Measure Pencil L evel SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 2 SINGLE THRESHOLD SHOWER Ce
17. ir of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warranty In no event will DreamLine be liable for costs of repair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modification or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be performed by either a DreamLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containi
18. n Body drops around the Drain Pipe and butt the Shower Base up against the studs See Fig 4 for details Lift and lower base over the center of The drain pipe and set it into the place Fig 4 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 13 4 Level the tray and place marks on the studs above the upper edge of the tile flange See Fig 5 for details Level base in two directions Fig 5 5 Mix the bedding material Mortar Plaster etc Concrete 15 recommended Apply enough bedding material to support the entire bottom of the shower base See Fig 6 for details Mortar Plaster Fig 6 SLIMLINE SHOWER Rev 3 Ver 5 07 2013 14 6 After the bedding material has been poured and before it sets place the shower base into the position with the drain assembly sliding over the PVC waste pipe It will be necessary to push the shower base until the top of the tile flange aligns with the marks drawn on the studs and the front edge is contacting the rough floor along the entire length of the shower base Ensure that the base is level in all directions You may need to use shims to hold the tray in the level until the bedding settles and supports the tray Remove all extra mortar See Fig 7 for details Fig Waterproof Drywall Waterproof Drywall 7 Allow the bedding material to completely harden before applying weight to the bottom of the shower bas
19. ng abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers end users or by any party other than DreamLine THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISCLAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERSON OR FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR OR MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and
20. nter Drain Configuration U MODEL SPECIFICATION D1 in DLT 1132320 32x37 DLT 1136360 36 x36 DLT 1136480 36 x48 30760 327x607 Mex i9 3 _ 60 3 i9 30 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 Left Hand Drain Configuration MODEL SPECIFICATION D1 in W1 in DITiisgdi 30 15 17 _ 32 15 DLT 1132601 32 x60 L 82 T _ 607 wq 12 DLT 1134601 34 x60 34 60 DLT 1136601 36 x60 SLIMLINE SHOWER Rev 3 Ver 5 07 2013 Right Hand Configuration WI D1 MODEL SPECIFICATION D1 in W1 in 30 x 60 mo ox ow ode oam omaa 36x59 1 i17 _ 36 6 ix _ SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 NEO SHOWER BASE 01722036360 36736 185 16 DLT 2088380 38538 38 20516 25 m DLT 2040400 40 22 5 16 14 3 8 DLT 2042420 4254 a SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 QUARTER ROUND SHOWER DLT 7033330 33 x33 21 5 8 DLT 7036360 36 36 21 5 8 DLT 7038380 38 x38 21 5 8 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 DOUBLE THRESHOLD SHOWER Corner Drain Configuration MODEL SPECIFICATION W in C in DLT 1032320 37x37 DLT 1036360 SLIMLINE SHOWER BASE Rev 3 Ver 5 07 2013 Left Hand Drain Configuration WI1 D1 MODEL SPECIFICATION D1 in W1 in
21. our unit carefully and inspect it Lay it out and identify all parts using parts diagram and part list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement NOTE Retain these installation instructions for future reference FLEX Enclosure Rev 1 Ver 3 03 2014 Door Assembly Diagram Alluminum profile Return Wall profile Stationary glass Return Glass panel _Expandable rail Corner profile Glass door N er Alluminum profile Expandable rail FLEX Enclosure Rev 1 Ver 3 03 2014 Shower Enclosure Installation NOTE The installation of this shower enclosure requires two installers NOTE The shower enclosure can be installed on the shower base or custom threshold 1 Prior to the Shower door installation Shower base installation and plumbing must be completed See Fig 1 for details 2 The width of the shower enclosure is adjustable and can be adjusted to the size of your shower base or custom threshold 0 Mark position of the Wall profile 01 the Return wall profile 11 on the wall according to the model size and dimensions provided in the size table Place the Wall profile and the Return wall p
22. rofile onto the Shower base or threshold against the finished wall and level it vertically See Fig 2 and table below for details Model No W1 W2 SHDR 2234340 RT 01 34 1 2 32 1 2 36 1 2 FLEX Enclosure Rev 1 Ver 3 03 2014 SHDR 2230300 RT 01 30 1 2 28 1 2 32 1 2 ke 3 Trace the drilling holes on the wall through the predrilled holes in the Wall profile 01 Drill the holes on the wall using a 5 16 drill bit and insert the Wall anchors 03 Apply a bead of silicone to the wall along the drilled holes and around the holes Attach the Wall profile to the wall with the Round head screws ST4 2x40 05 See Fig 3 and Fig 5 for details 4 Trace the drilling holes on the wall through the predrilled hole in the Return wall profile 11 Drill the holes on the wall using a 5 16 drill bit and insert the Wall anchors 03 Apply a bead of silicone to the wall along the drilled holes and around the holes Attach the Return wall profile to the wall with the Round head screws ST4 2x40 05 See Fig 4 and Fig 5 for details FLEX Enclosure Rev 1 Ver 3 03 2014 5 16 I FIN CUT N 27
Download Pdf Manuals
Related Search