American Standard 2833.128.020 Installation Guide
Contents
1. ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed on chart MODELS DIMENSION A 2383 010 2830 128 _ E 2384 010 2833 128 FINISHED WALL 2386 010 2836 128 254mm 10 2756 016 2849 128 2383 012 2758 813 2384 012 2829 128 2386 012 2832 128 SUPPLY _ 2 2386 800 2835 128 AS 2431 010 2835 813 305mm 12 REQ D 2431 101 2232 128 2755 016 2235 128 2758 128 2235 813 FINISHED FLOOR 2758 800 2383 014 2386 014 356mm 14 2384 014 2757 016 14 ROUGHS CLOSET SEALANT FLANGE TAPERED s WASHER CLOSET Pa INSTALL WAX SEAL INSTALL CLOSET BOLTS Invert toilet on floor cushion to prevent POSITION TOILET ON FLANGE Install closet bolts in flange damage and install wax ring evenly a Unplug floor waste opening and install toilet on closet flange channel turn 90 and slide around waste flange horn with tapered so bolts project through mounting holes into place 6 152mm apart end of ring facing toilet Apply a thin bead b Loosely install retainer washers and nuts Side of washers and parallel to wall of sealant around toilet base marked THIS SIDE UP must face up AS America Inc 2011 730928 100 Rev Q Product names listed herein are trademarks of AS America Inc USE FUTURE R F O SAVE For Tanks Bowls using Speed Connect System Tank mounting bolts pre installed TANK MTG BOLTS PRE BO TCAP I2. 0 Avebury Rd AS Maquila S A de C V Piscataway New Jersey 08855 Mississauga Ontario Via Morelos 330 Attention Director of Consumer Affairs Canada L5R 3M3 Col Santa Clara Ecatepec 55540 Edo Mexico For residents of the United States warranty Toll Free 800 387 0369 www americanstandard com mx information may also be obtained by calling www americanstandard ca the following toll free number 800 442 1902 www americanstandard us com a 730928 100 Rev Q
3. INSTALLATION INSTRUCTIONS American Standard CARE AND MAINTENANCE Style That Works Better CADET 3 1 6 GPF TWO PIECE TOILET Models 2383 2384 2386 2431 2755 2756 2757 CAD ET CADET 3 FloWise 1 28 GPF TWO PIECE TOILET Models 2232 2235 2758 2829 2830 2832 2833 A Ei 2835 2836 2849 2431 E Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed
4. LING 7 WASHER WASHER CONE WASHER _ COUPLING _ EXISTING NUT COUPLING COUPLING NUT NUT METAL COPPER FLARED TUBING WATER WATER WATER WATER B SHUT OFF SHUT OFF SHUT OFF B SHUT OFF B o p p Captive cone washers already Use existing spiral cone washer Fluidmaster cone included No washer may not additional washers water leakage Water supply seal completely on needed tube or pipe must extend at spiral type supply least 1 2 inside threaded line These parts must be used as illustrated to insure water tight connection Use of existing coupling nut may result in Use existing coupling nut and washer With correct washers in place see Step 9a shank of valve does not apply to flanged tubing CAUTION DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE CAUTION Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding tighten COUPLING NUT 1 4 turn beyond hand tight DO NOT OVERTIGHTEN WARNING Do not use plumber s putty pipe dope or any other sealant on the water supply connection to this tank If the connection leaks after hand tightening replace the supply line If the connection continues to leak with the new supply line replace the fill valve Warranty is void if any type of sealant is used on the water supply connection 730928 100 Rev Q Adjust Water Level Water Level To Level Indicated Adjustment Knob On Tank By
5. NSTALLED INSTALL TANK a Install large rubber gasket over threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening and tank mounting bolts go through mounting holes Secure with metal washer nut combo WASHER NUT INSTALL TOILET a Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange Alternately tighten nuts until toilet is firmly seated on floor With tank parallel to wall alternately tighten nuts until tank is snugged down A CAUTION evenly against bowl surface DO NOT OVERTIGHTEN NUTS OR BASE Maree DAMAGEDI USE INCLUDED TOOL NUT DRIVER OR DEEP SOCKET RACHET Install caps on washers If necessary cut bolt height to size before installing caps A CAUTION DO NOT OVERTIGHTEN NUTS MORE Smooth off the bead of sealant around base THAN REQUIRED FOR A SNUG FIT Remove excess sealant si INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer s directions Before continuing determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply DO NOT use plumber s putty to seal these fittings METAL FLANGED METAL SPIRAL VINYL BRAIDED TUBING TUBING CONNECTOR E LOCK NUT N LOCK NUT N LOCK NUT N LOCK NUT CONE XN EXISTING EXISTING COUP
6. Turning Refill Tube Water Level l i Adjustment Knob Trip Lever Rod To Move Float h Cup Up Or Down Approximate Water Level Float Cup Flotador Flush Valve _ Chain Fill Valve Cadena de la Or Water V lvula de Control Descarga Overflow Flapper Seal N Tank to Bowl Gasket Water Supply Line CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth WARNING Do not use in tank cleaners These products can seriously corrode fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any damage caused by the use of in tank cleaners 3 730928 100 Rev Q TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 13 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The end of the refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time Fluidmaster Model 242 Replacement Seal may be needed IMPORTANT Always clear e While holding a container e Replace TOP by engaging Go to o
7. s fluidmasterguide pdf Poor or Bowl water level too low Check that refill tube is connected to water control and sluggish inserted into overflow tube without being kinked or damaged flush Supply valve partly closed Open supply valve fully Be sure that proper supply tube size is used Partially clogged trapway and or drain pipe Remove obstruction Consult a plumber if necessary and or vent Supply pressure too low Normal supply pressure must be at least 20 psi Toilet leaks Poor supply line connection Review Step 8 of installation procedure Poor bowl to tank floor connection Review Step 1 through 6 of installation procedure Toilet does Flapper seal leaking or deformed Clean debris from seal surface Replace flapper seal as needed not shut off b Sand or debris lodged in water control Shut off water supply Remove cap and clean as per Fluidmaster maintenance instructions at Flush valve chain too tight holding www americanstandard us com enews fluidmasterguide pdf flapper open Readjust chain length as needed Toilet bowl Wax ring not fully compressed Retighten bowl to floor knobs rocks after Floor not level Use toilet shims and or place a bead of caulk around the base of installation the toilet FOR REPAIR PARTS LIST SEE UNDER TANK LID In the United States In Canada In Mexico American Standard Brands AS Canada ULC Customer Service Manager P O Box 6820 590
8. ur website at www fluidmaster com for more solutions sand and rust from system over the uncapped VALVE lugs and rotating 1 8 turn to toilet problems e Make sure water supply is to prevent splashing turn clockwise MAKE CERTAIN For troubleshooting information please contact oft Remove valve TOP by arames Laava water LOCKED POSITION VALVE Maara a ege mynor Fluidmasterine counterclockwise pressing IS NOT FULLY TURNED TO 30800 Rancho Viejo Road down slightly on cap THE LOCKED POSITION San Juan Capistrano CA 92675 F oer 949 728 2000 800 631 2011 Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster shall www fluidmaster com not be responsible or liable for any damages caused by products used with Fluidmaster valves that were ooreis juiamaster Inc not manufactured by Fluidmaster Inc Registered trademark of Fluidmaster Inc See Step 10 For Diagram Troubleshooting Guide Problem Possible Cause Corrective Action Does not a Water supply valve closed Open valve and allow water to fill tank flush b Supply line blocked Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Flush valve chain too loose or disconnected Readjust chain length as required Sand or debris lodged in water control Shut off water supply Remove cap and clean as per Fluidmaster maintenance instructions at www americanstandard us com enew
Download Pdf Manuals
Related Search