American Standard 2795204.020 Installation Guide
Contents
1. U SE FUTURE R F O SAVE Apply weight evenly Do not move after placement Water tight seal may break Thread then hand tighten water supply A Hand Tighten Only Do Not Overtighten Tighten handles alternately until tank contacts bowl HAND TIGHTEN ONLY TIP Place 2 pieces of masking tape on floor as shown to help with alignment in step 6 For seat installation see instructions included with seat A WARNING Overtightening of water supply line nuts could result in breakage and potential flooding If the connection leaks after hand tightening replace the supply line Do not use any type of sealant on the water supply connection A Use of plumber s putty pipe dope or any other type of sealant will void the warranty 7301692 100 Rev C SEE STEP 12 Rod Adjustment SEE STEP 13 IMPORTANT Refill Float Adjustment If short flush does not refill the bowl turn thumbscrew CCW 1 turn flush repeat if necessary Install and adjust push button rods for about 1 16 1 1 2mm clearance between rod snd and valve butto Turn on water supply Submerge the FLOAT CUP under the water Ma eT ee SEE STEP 13 TIPS for 30 seconds Adjust the water n a E l to desired level by turning WATER ADJUSTABLE LEVEL ADJUSTMENT ROD and HEIGHT moving FLOAT CUP up or down LOCK NUT THREADED x E SHANK Diagram 1 LEJ FLUSH PUSH BUTTONS e The large flush button should line up over the LARGE FL2. 221 ari S O S pennn NOTE Distance from wall to Style That Works Better uct closet flange centerline must Hossa 140mm CENTERS be as listed below 14 18 1 2 356mm T J 470mm SUPPLY IMPORTANT Water supply F REQUIRED position 1 or position 2 on the wall is required at ae TEPE 2 1 4 or 8 from centerline sajas H h 140mm 1 of the toilet See rough in QO ae R Cae ARA BACK VIEW First suggested position is 7412 18 14 16 cis i 191mm i 347mm ISHED a oem for reference hidden behind the toilet The 12 gue m 305mm 1 geom wy of Ihe toilet gives RIGHT HEIGHT ROUND FRONT 2 PIECE TOILET space for this installation FINISHED p 28 1 4 The second suggested J aa Cmm 221mm position is next to the toilet Between these two PrE E ERT Sas HOLES 5 1 2 positions the space for the Ve 140mm CENTERS supply between wall and L e toilet is limited to 4 1 2 In AT te o o p g REQUI RED Soe j this case check your supply i nea position 2 and hose dimensions 16 1 2 NS 419mm a 5 1 2 264mm 140mm i 7 1 2 12 7 8 6 BACK VIEW 191 aioe 328mm FINISHED 152mm for reference 12 y l FLOOR 12 3 16 305mm 309mm 73016 Product names listed herein are trademarks of AS America Inc i ee a 92 100C
3. INSTALLATION INSTRUCTIONS l CARE AND MAINTENANCE American Standard Studio Dual Flush Concealed Trapway Right Height Elongated Model 2794 Right Height Round Front Model 2795 D ey eo Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this ae centied by product is installed properly please read these instructions carefully before you begin Certain installations nee may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed RIGHT HEIGHT ELONGATED 2 PIECE TOILET FINISHED WALL ROUGHING IN k 30 114 768mm D l M E N l N
4. ON VALVE MAY NOT TURN ON IF TOP IS NOT FULLY TURNED TO THE LOCKED POSITION For troubleshooting information please contact Fluidmaster me 30800 Rancho Viejo Road San Juan Capistrano CA 92675 949 728 2000 800 631 2011 Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster Inc www fluidmaster com u d aSIEr C 2001 Fluidmaster Inc Registered trademark of Fluidmaster Inc BOWL NUMBER REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked inside tank NOTE XXX represents color or trim finish options Specify when ordering PART NUMBER 738168 XXX DESCRIPTION TANK COVER 3053 3075 7301540 200 XXX0A BOLT CAP KIT 738565 457 0070A FLUIDMASTER INLET VALVE 7381205 400 0070A DUAL FLUSH VALVE ASSEMBLY 7381213 200 0070A FLUSH VALVE SEAL 7381 147 200 0070A EZ TANK COUPLING KIT 7381203 201 0070A PUSH BUTTON ASSEMBLY 738570 1040A REFILL TUBE 5121 110 XXX VN SEAT ROUND FRONT 5218 110 XXX NN ONNINSSSSS SEAT ELONGATED TROUBLESHOOTING GUIDE POSSIBLE CAUSE CORRECTIVE ACTION Does not flush a Water supply valve closed b Water supply line blocked c Sand or debris lodged in water control Poor or sluggis
5. USH BUTTON SMALL FLUSH BUTTON white actuator on the flush tower in the tank FOR SOLID WASTE FOR LIQUID WASTE 1 6 gal flush 1 1 gal flush e The small flush button should line up over the 6 Liter flush 4 1 Liter flush gray actuator on the flush tower in the tank e Pressing both buttons at once will result in a short flush TIPS With the lid removed directly press the flush button in the tank to confirm that the toilet is working properly If not follow troubleshooting guide Install Threaded Rods into holes in bottom of push buttons approximately 1 2 12mm Lightly snug Locking Nut Place Lid on Tank tockn ts Push Button to test flush If more stroke is needed loosen Locknut and turn Threaded Rod counterclockwise one 1 turn Replace Lid Repeat until flush action is achieved Threaded Rods If Valve stays open turn Threaded Rod clockwise one 1 turn and lightly snug Locknut CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish A WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and prop
6. enance c Set water level to mark on back of tank In Canada AS Canada ULC 5900 Avebury Rd Mississauga Ontario Canada L5R 3M3 In Mexico American Standard B amp K Mexico S de R L de C Via Morelos 330 Col Santa Clara Ecatepec 55540 Edo Mexico Toll Free 01 800 839 1200 www americanstandard com mx Toll Free 800 387 0369 www americanstandard ca 7301692 100 Rev C
7. erty damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite Pe a 7301692 100 Rev C NOTE Pictures are representative and may not TROUBLESHOOTING exacily depict the flush valve IMPORTANT Always clear sand and rust from system e Make sure water supply is off Remove valve TOP by lifting arm and rotating top and arm 1 8 turn counterclockwise pressing down slightly on cap e While holding a container over the uncapped VALVE to prevent splashing turn water supply on and off a few times Leave water supply off IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 15 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The end of the refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some ame Fluidmaster Model 242 Replacement Seal may be needed Go to our website at www fluidmaster com for more Replace TOP by angaging lugs solutions to toilet problems and rotating 1 8 turn clockwise MAKE CERTAIN TIP IS TURNED TO THE LOCKED POSITI
8. h flush a Tank water too low b Bowl water too low c Water supply valve partly closed d Partially clogged trapway and or drain pipe e Supply pressure too low a Open valve and allow water to fill tank b Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble c See Fluidmaster maintenance see Step 15 a Check that the water level is set to the mark inside the tank b Check that the refill tube is connected to the water control and flush valve port Adjust refill float down until bowl water is restored see Step 11 c Open water supply valve fully Be sure that proper supply tube size is used d Remove obstruction Consult a plumber if necessary e Minimum water supply pressure 20psi Wait for tank to refill and or vent Toilet leaks a Poor supply line connection a Review Step 9 b Poor bowl to floor connection b Review Step 6 Toilet does not shut off a Flush valve seal leaking or deformed b Sand or debris lodged in water control c Water level set too high In the United States American Standard Brands P O Box 6820 Piscataway New Jersey 08855 Attention Director of Consumer Affairs For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902 www americanstandard com a Clean debris from seal surface Replace flush valve seal as needed b See Step 15 Fluidmaster maint
Download Pdf Manuals
Related Search