American Standard 2886.216.222 Installation Guide
Contents
1. FINISHED WALL CLOSET BOLTS SUPPLY AS INSTALL CLOSET BOLTS Install closet bolts in flange channel and slide into place parallel to wall SEALANT NUT cle TAPERED WASHER CLOSET Va POSITION TOILET ON FLANGE a Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes b Loosely install retainer washers and nuts Side of washers marked THIS SIDE UP must face up INSTALL WAX SEAL Invert toilet on floor cushion to prevent damage and install wax ring evenly around waste flange horn with tapered end of ring facing toilet Apply a thin bead of sealant around toilet base Product names listed herein are trademarks of AS America Inc 7301416 100 Rev F AS America Inc 2009 USE FUTURE R FO SAVE RUBBER RUBBER GASKET BOLT CAP INSTALL TANK a Insert rubber grommets through holes in the tank then insert bolts through holes in the grommets Install large rubber gasket over threaded outlet on bottom of tank and CLOSET BOLT WASHER NUT INSTALL TOILET a Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange lower tank onto bowl so that tapered Alternately tighten nuts until toilet is firmly seated on end of gasket fits evenly into bowl floor water inlet opening With tank parallel to wall alternately tighten nuts until tank is snugged down evenly against bowl surface A CA2. VALVE 738565 429 0070A FLUIDMASTER BASE VALVE 12 738657 100 0070A REFILL TUBE 738657 101 0070A REFILL TUBE 7381042 0070A FLUSH VALVE SILICONE SEAL 034783 XXX0A BOLT COUPLING KIT 7301476 100 0070A TANK COUPLING KIT NOTE Pictures are representative and may not TROUBLESHOOTING exactly depict the flush valve IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 13 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The end of the refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time Fluidmaster Model 242 Replacement Seal may be needed IMPORTANT Always clear While holding a container sand and rust from system e Make sure water supply is off prevent splashing turn water MAKE CERTAIN TIP IS TURNED Remove valve TOP by lifting arm supply on and off a few times TO THE LOCKED POSITION ae and rotating top and arm 1 8 turn Leave water supply off VALVE MAY NOT TURN ON IF For troubleshooting information please contact counterclockwise pressing down TOP IS NOT FULLY TURNED TO e Replace TOP by engaging lugs over the uncapp
3. apply slight downward pressure and twist it until the flush valve disengages from the bayonet e To reinstall Flush Valve reverse the above procedure making sure the blue Small Flush Button will line up with the Small Flush Button with 3 dots on the Tank Lid Turn on water supply Submerge the FLOAT CUP under the water for 30 seconds Adjust the water to desired level by turning WATER LEVEL ADJUSTMENT ROD and moving FLOAT CUP up or down Pressing both buttons at once will flush the small flush amount 0 9 gal flush or 3 4 L flush The Small Flush Button with 3 dots should line up over the blue actuator on the flush tower in the tank The Large Flush Button with 9 dots should line up over the white actuator on the flush tower in the tank Small Flush Button with 3 dots for liquid waste 1 0 gal flush 3 8 L flush Large Flush Button with 9 dots for solid waste 1 6 gal flush 6 L flush TIPS If the flush doesn t flush properly after eliminating other causes remove the tank lid and directly push the flush button in the tank If the flush works you will need to adjust the push button mounted on the tank lid with the settings as follows 1 Turn the lid upside down Loosen the black plastic lock nut Adjust the white threadrod one turn counterclockwise Re tighten the black plastic lock nut Put lid back on tank and test If it is still not flushing properly repeat steps 1 through 4 until the probl
4. INSTALLATION Americam Standard INSTRUCTIONS Style That Works Better Siphonic Dual Flush Two Piece Toilet Models 2886 2887 2889 3380 3381 lt a Certified by IAPMO R amp T Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed below A 12 305mm CLOSET FLANGE
5. UTION DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED Install caps on washers If necessary cut bolt height to size before installing caps Smooth off the bead of sealant around base Remove excess sealant A CAUTION DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer s directions Before continuing determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply VINYL BRAIDED CONNECTOR SPS Lock NUT COUPLING METAL COPPER METAL FLANGED METAL SPIRAL FLARED TUBING TUBING TUBING E LOCK NUT LOCK NUT N LOCK NUT CONE gt EXISTING EXISTING lt WASHER WASHER CONE WASHER COUPLING NUT COUPLING NUT _ COUPLING EXISTING NUT WATER WATER WATER SHUT OFF SHUT OFF N SHUT OFF IE Captive cone washers already Use existing spiral cone washer Fluidmaster cone included No washer may not additional washers water leakage Water supply seal completely on needed tube or pipe must extend at spiral type supply least 1 2 inside threaded line These parts must be used as illustrated to insure water tight connection Use of existing coupling nut may result in Use existing coupling nut and washer shank of valve does not apply to flanged tub
6. ed VALVE to and rotating 1 8 turn clockwise Go to our website at www fluidmaster com for more solutions to toilet problems RoW slightly on cap THE LOCKED POSITION Fluidmaster ne i a 30800 Rancho Viejo Road Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products San Juan Capistrano CA 92675 Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster Inc 949 728 2000 800 631 2011 www fluidmaster com 2001 Fluidmaster Inc Registered trademark of Fluidmaster Inc TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Does not flush a Water supply valve closed a Open valve and allow water to fill tank b Supply line blocked b Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Also see Fluidmaster maintenance see step 13 Push button not properly set Readjust push button rod length as required Refer to step 12 Sand or debris lodged in water control d Shut off water supply Remove cap and clean per Step 13 Poor or sluggish flush Bowl water level too low Check that refill tube is connected to water control and inserted into refill float without being kinked or damaged b Supply valve partly closed Open supply valve fully Be sure that proper supply tube size is used Partially clogged trapway and o
7. em is resolved If one counterclockwise turn is too much and causes the flush valve to stay open adjust 1 2 turn clockwise and return to step 4 CARE AND CLEANING ll ll BLACK PLASTIC LOCK NUT Te BLACK PLASTIC LOCK NUT SI p BLUE THREAD ROD J WHITE THREAD ROD When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish A WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite 7301416 100 Rev F REPAIR PARTS LIST TANK NUMBER Repair parts are determined by toilet tank number which can be found marked inside tank 4349 216 4349 516 NOTE XXX represents color or trim finish options Specify when ordering 4348 216 4348 516 4339 216 4339 516 PART NO DESCRIPTION Without Liner With Liner 735138 400 XXX TANK COVER 7381092 200 XXX0A RECTANGLE PUSH BUTTON 7381091 400 0070A DUAL FLUSH VALVE 7381091 401 0070A DUAL FLUSH
8. ing CAUTION DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE CAUTION Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding With correct washers in place see Step 9a tighten COUPLING NUT 1 4 turn beyond hand tight DO NOT OVERTIGHTEN A WARNING Do not use plumber s putty pipe dope or any other sealant on the water supply connection to this tank If the connection leaks after hand tightening replace the supply line If the connection continues to leak with the new supply line replace the fill valve Warranty is void if any type of sealant is used on the water supply connection 7301416 100 Rev F ADJUSTMENTS a NIPPLE REFILL a P SET WATER x HERE b Adjust water level Water level should be adjusted to level indicated on tank by adjusting float cup See Step 11 for water level adjustment method Flush Valve Setting Adjustments With Liner Tank 4349 516 4348 516 4339 516 Flush Valve Without Liner Tank 4349 216 4348 216 4339 216 Full Flush Adjustment WATER LEVEL ADJUSTMENT b RELEASE SILICONE THREADED SHANK PARTS FOR WATER CONNECTION SEE STEP 9 CONE WASHER gay COUPLING NUT WW HAND TIGHT ONLY Diagram 1 LP FLUSH BUTTONS ON TANK Partial Flush Adjustment NOTE All other settings will result in either more or less water and is not recommended e To remove Flush Valve
9. r drain pipe and or vent Remove obstruction Consult a plumber if necessary Supply pressure too low d Normal supply pressure must be at least 20 psi Toilet leaks Poor supply line connection a Review Step 9 of installation procedure Poor bowl to tank floor connection Review Step 4 through 7 of installation procedure Toilet does not shut off Push button rod is too long holding flush valve open a Readjust rod as needed Review step 12 Flush valve seat and or seal worn or deformed Replace seal flush valve assembly as needed Sand or debris lodged in water control Shut off water supply Remove cap and clean per Step 13 Sa 7301416 100 Rev F
Download Pdf Manuals
Related Search