Home

Mr. Steam S3C1IAFWH Installation Guide

1. Do not operate the iSteam 2 0 control with other than a Mr Steam iSteam 2 0 compatible steam generator Mr Steam residential steam generators with serial numbers lower than 930030 or any other brand of steam generator are not to be operated with iSteam 2 0 controls Doing so may result in an inoperative installation If your generator s serial number is lower than 930030 contact Mr Steam Technical Service for upgrade options and components to enable your steam generator to function with iSteam 2 0 e This document contains important safety operation and maintenance information Leave this document with the homeowner Do not discard this document e Discontinue use of the steam generator or control if the steam generator is damaged or otherwise not functioning properly Doing so may result in an inop erative or hazardous installation e Refer to the Steambath Generator Installation Operation and Maintenance Manual PN 100472 for locating and installing the steamhead Do Not alter or modify any Mr Steam products Doing so may result in an inoperable or hazardous installation and will void the warranty mr steam Locating the Control Determine the desired installation location of the control The iSteam 2 0 controls are designed to be installed inside or outside the steam room as a matter of personal preference If the control is installed inside the steam room Locate the control 4 5 feet above the floor near the bathe
2. Route the control cable from the wall cutout to the steam di df generator Connect one end of the cable to the steam generator if n Ln connector The two ends of the control cable are the same 9 N ME y BEd rd Ss a d Wa STEP 2 When used route the AudioWizard Cable from the wall cut out to the AudioWizard The two ends of the AudioWizard cable are the same See the AudioWizard Installation Operation amp Mainte nance Manual PUR 100478 for complete AudioWizard Installation instructions Q IMPORTANT NOTE Be careful not to strain staple pinch or otherwise damage the control cable Route cable as required to permit replacement Do not route cable inside conduit together with power lines or close to hot water or steam piping Finish the iSteam 2 0 installation using the instructions on page 7 6 mr steam Controls Installation Instructions for iSteam 2 09 STEP 1 PLUG the 30 control cable into the iSteam 2 0 control pigtail 1a The iSteam 2 0 pigtail is the longer cable with the ID Tag If the optional AudioWizard is used remove the Red Cap from the AudioWizard pigtail 1b and plug it into the AudioWizard cable NGOS Do not force or twist cable ends together Forcing or twisting cable ends may damage the connectors N N N i Control N H Cable QOH Rd Bird Cable Steam Generator See the AudioWizard Installation Operation and Maintena
3. 2 NPT 1 DO NOT install any valve in steam line Flow of steam must be unobstructed 2 Use 1 2 inch brass pipe or copper tubing from unit to steam head as permitted by codes 3 Insulate steam line using pipe insulation rated 212 F or higher 4 Pitch steam line 1 4 per foot towards steam head or steam generator to avoid valleys and trapping of condensate NOTE Running the steam line down and then up will create a steam trap blocking the flow of steam NOTE A 1 5 hole in the steam room is required to mount the steamhead SAFETY VALVE 34 NPT Where permitted by local codes provide an outlet plumbing connection for safety valve ANQZSG OIRO To insure proper and automatic safety valve operation DO NOT connect a shut off valve or a plug at safety valve outlet DO NOT connect a shut off valve or any obstruction in steam supply pipe DO NOT connect the safety valve output into the steam line DRIP PAN Mr Steam strongly recommends the use of a drip pan in the unlikely event of a plumbing leak Check local plumbing codes for receptor trap and vent requirements Drip pans drain by gravity The drip pan is equipped with an integral 3 4 fitting See page 15 for additional drip pan installation information AROMASTEAM If the optional AromaSteam Electronic Oil Delivery System PN MS AROMA is to be installed a 90 degree T plumbing fitting must be installed at a designated location on the steam outlet line See the Mr Steam Ar
4. The location where this owner s manual is kept shall be written in the space provided on the label using permanent ink SIBBITI COM PURATA 7 14 Not Actual Size For a replacement warning label contact Mr Steam customer service at 1 800 76 STEAM or hello mrsteam com mr steam OSETTING THE STEAM BATH TEMPERATURE AND DURATION NWZSNING Set the steam bathing temperature according to personal preference however it is highly rec ommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels Set duration to a maximum of 10 minutes to gauge comfort and safety levels This will allow the steam generator to heat up and begin producing steam SAFETY AND OPERATING INFORMATION DO NOT install or use any iSteam iTempo Plus iTempo HomeWizard or iGenie controls without reading and understanding the Mr Steam steam generator Installation and Operation Manual Failure to read and understand these instructions may result in an inoperative or hazardous installation ANQZSIXIN The peel and stick warning sticker located in this manual must be read and permanently affixed in a conspicuous location near the steam room Failure to read and affix this warning sticker in a conspicuous location may result in serious injury or death If an iSteam iTempo or iTempo Plus control is installed outside the steam room a Remote Temperature Probe PN MSTS or iMSTS must be installed inside the steam
5. dd he Installation Operation and Maintenance Manual Steambath Generator Systems Residential Models MS90E MS400E and MSSUPERT1E 6E mr steam Feel Good Inc READ ME FIRST ANWZEGINTE As you follow these instructions you will notice warning and caution symbols This blocked information is important for the safe and efficient installa tion and operation of this generator These are types of potential hazards that may occur during installation and operation ANTNNLDTS Indicates a potentially hazardous situation which if not avoided could result in death or serious injury VAM CAUTION Indicates a potentially haz ardous situation which if not avoided may result in minor or moderate injury or product damage IMPORTANT NOTE This highlights information that is especially relevant to a problem free installation All information in these instructions is based on the latest product information available at the time of publication Sussman Automatic Corporation reserves the right to make changes at any time without notice When installing and using this electrical equipment basic safety precautions should always be followed including the following IMPORTANT SAFETY INSTRUCTIONS 1 READ AND FOLLOW ALL INSTRUCTIONS 2 DO NOT permit children under D Excessive temperatures have a high the age of 16 to use this steambath potential for causing fetal damage dur 3 Steam is hot and can cause
6. 43 20 34th Street Long Island City NY 11101 9410 S La Cienega Blvd Inglewood CA 90301 TEL 1 800 76 STEAM Fax 718 472 3256 TEL 1 800 72 STEAM Fax 310 216 2944 mr ste am Sussman Automatic Corporation hello mrsteam com www mrsteam com us 2014 Sussman Automatic Corporation Mr Steam and des AromaFlo AutoFlush AutoSteam Butler Package ChromaSteam Clean Steam Every Time Club Therapy Digital 1 Express Steam From Bathroom to Spa iGenie iSizing iSteam iSteam Plus Making Wellness a Way of Life MusicTherapy Spa Package Steam Genie Steam on Demand Steam Home iTempo iTempo Plus SteamTherapy Sussman Valet Package Virtual Spa System Voice Genie and Voice Wizard are registered trademarks of Sussman Automatic Corporation AudioWizard A Lifetime of Pleasure Home Wizard iButler iSteamTV iTempo iTempo Plus MySteam Smart Sizing Steam in a Box SteamStart SteamStop The Intelligent Steambath are trademarks of Sussman Automatic Corporation PUR 1004724 Rev 3 15 dd he Installation Operation amp Maintenance Manual Steam 2 0 Control Feel Good lnc mr steanr READ ME FIRST ZA WARNING As you follow these instruc tions you will notice warning and caution symbols This blocked information is impor tant for the safe and efficient installation and operation of this generator These are types When installing and using this electrical equipment basic safety precautions should alw
7. lesen 5 Installation Plumbing Water Supply Drain Steam Outlet Safety Valve Drip Pan AromaSteam 6 Steam Head Installation SS se ss se eee 7 Steam Generator Dimensions 0 00005 8 Electrical Specifications amp Field Power Wiring 9 viri ed Marais yeasts age pees ITO a LoT T 10 11 Optional Tandem Cable Diagram 11 Initial Start Up Gc Check ut so sg eg owe ada ee qon Re ms 12 Optional amp Accessary Equipment 12 Troubleshooting sesse borat drea D RR E OH RR ed 12 System Status Codes ene 13 Liquid Level Control Board 0 004 13 Optional AutoFlush System llle 14 Sou AE od TP 15 Optional Express Steam 2 cae quce oda drehen ied desc det 15 Parts Identification Diagram SEE SE ee see 16 Replacement Parts List eus guns Ies db pr eee edges 17 CONTROL INSTALLATION Before Installing cetera oom qao UR a oes Ae aeta Tea 18 Eer rol koue el sae sd SERE SEG eee EEG 18 HOMEOWNER SECTION Important Safety Instructions ES see 19 Setting Steam Bath Temperature amp Duration 20 Safety amp Operating IS uiuo m ace e pce sor o onus 20 Care Tips for Controls and Generator Maintenance 20 Using the AromaSteam Essential Oils sun 21 Ee OER AAR OE EE ER RE EE EE OR TED 21 mr steam Feel Good Inc mr steam Installation Operation amp Maintenance Manual SELECT YOUR MR STEAM I
8. room per installation instructions supplied with the Remote Temperature Probe Failure to install according to instructions will result in an inoperative control and overheating of the steam room To prevent slip and fall hazards non skip strips must be installed on the steam room floor DO NOT alter or modify any Mr Steam product Doing so may result in an inoperative or hazardous installation and will void the UL listing and warranty IMPORTANT NOTES Malfunction due to power spikes lightning fire freezing or flooding is not covered under the warranty Discontinue use of the steam generator or control if the steam generator is damaged or otherwise not functioning properly Doing so may result in an inoperative or hazardous condition 20 Installation Operation amp Maintenance Manual CARE TIPS FOR ALL CONTROLS AND STEAMHEADS 1 Use only mild soap and water on a soft cloth to clean the control and steamhead 2 DO NOT use abrasive cleansers 3 If the decorative cover is damaged on the iTempo or iTempo Plus call Mr Steam technical service for replacement parts NOTE Replacement of the decorative covers requires removal and reinstallation of the control from the mounting surfaces STEAM GENERATOR MAINTENANCE Mr Steam steambath generators require little maintenance Other than periodic draining maintenance procedures are mini mal Every 2 months or more often in hard water areas the manual drain valv
9. Department for installation of any equipment not shown in these instructions East Coast 800 767 8326 West Coast 800 727 8326 WARRANTY To view or download the Mr Steam m Controls amp Accessories Warranty and register your product go to blog mrsteam com wr AutoFlush Shown Fully Assembled Generator de Plumb to Drain Line Drain Valve DO NOT TURN OR REMOVE THE DRAIN VALVE shown in the correct open position INSTALLING AUTOFLUSH ON OLDER MODEL GENERATORS 5N 899 999 and below 1 Remove the connector from the C location in the jacket Cut off the connector where shown and strip back the wires approx 0 375 Cut the connector off the AutoFlush cable where shown and strip back the wires approx 0 375 Remove the knockout in the side of the genera tor and install a bushing to prevent chafing Route the wires from the AutoFlush through the knockouts and connect the white wire from the AutoFlush to the white wire from the circuit board using a wire nut Repeat for the black Wire n
10. Operation amp Maintenance Manual PARTS IDENTIFICATION DIAGRAMS Contactor Liquid Level Control Board MS REGULAR MODELS MS65E MS400E Liquid Level Probe with AutoFlush Power Supply Knock Out shown with cover removed Transformer __ Water Feed Solenoid Se Water Inlet Plug and Play Connection see page 13 _ Steam Outlet Access Cover f NOTE FOR ILLUSTRATIVE PURPOSES ONLY Some components may be omitted or altered for clarity DO NOT use for wiring repair or other purposes not related to AutoFlush Valve optional component identification Express Steam d 7 Heater optional Heating Element Stainless Steel Tank d Nipple Manual not included Drain Valve MS SUPER MODELS MS SUPER 1E MS SUPER 6E with AutoFlush shown with cover removed Liquid Level Control Board Contactor mY zZ Water Feed Liquid Level Probe E Solenoid NOTE Super 1E 240 1 Power Supply Knock Out models are not supplied with internal fusing pem a Plug and Play Connection see page 13 Element CR Access Cover NOTE FOR ILLUSTRATIVE PURPOSES ONLY Some components may be omitted or altered for clarity DO NOT use for wiring repair or other purposes not related to AutoFlush Valve optional component identification Express Steam ee heater optional Heating Element Manual not inc
11. SETTINGS PG 11 Dashboard Screen The Dashboard displays key steam bathing ep features and optional accessories in one convenient screen The key features include TIME TEMPERATURE and USER settings The Chromasteam optional accessories include the ChromaSteam siene EAN AromaSteam and AudioWizard mr steam Timer Pc 9 Preferences PG 10 Set Timer Screen Press the TIMER button on the Dashboard to ac xd cess the SET TIMER screen Swipe your finger a a T from left to right to select the desired time 1 60 S ET TIMER minutes Press CANCEL to return to the Press to MUS op Steam Dashboard without changing the time Press HOME to return to the Dashboard saving the Timer 25 Minutes time for this steambath session only Press SAVE swipe area to save the time setting as the new default or as the selected user setting The control will turn off when the steambath session times out Then the START screen will be displayed mr steam Controls Set Temperature Screen 8 19 AM mr steam Press the TEMPERATURE button on the Dashboard SET TEMPERATURE user 4 to access the SET TEMPERATURE screen l am e Temperature The control is preset and will display a temperature set swipe area IE ting of 110 F default setting Swipe your finger from left to rightto adjust the desired temperature 80 120 F in one degree increments Press CANCEL to return to the Dashboard without chang E ing the t
12. STEAM ROOM GUIDELINES 1 Steam room must be completely enclosed with full walls door floor and ceiling 2 It is recommended that a gasketed door is used for steam containment 3 ANIESSBTS To prevent slip and fall hazards non skip strips must be installed on the steam room floor 4 Check the suitability of any materials with the manufacturer Walls and ceilings must be constructed of water resistant non corrosive surface such as tile marble molded acrylic or other non porous material 5 The ceiling should be sloped to prevent dripping of condensate 6 Provide a floor drain 7 No heating venting or air conditioning devices should be installed inside the steam room 8 Steam room tile construction information is available from the Tile Council of America Inc by purchasing the TCA Handbook for Ceramic Tile Installation Tel 864 646 8453 or www tileusa com 9 Windows that are part of the steam room should be double paned and tempered safety glass 10 Limit steam room ceiling height to 8 feet Exceeding 8 feet may require a higher rated steam generator NUZSSNINS Never use damaged equipment doing so may result in an inoperative or hazardous installation e Discontinue use of the steam generator and control if the steam generator or control are damaged or otherwise not functioning properly Doing so may result in an inoperative or hazardous installation e ELECTRICAL SHOCK HAZARD Mr Steam steam gen
13. SUPPLY DISCONNECT WITHIN SIGHT OF THE STEAM GENERATOR OR ONE N THAT IS CAPABLE OF BEING LOCKED IN THE OPEN POSITION AS REQUIRED BY CODE Contact FIELD POWER WIRING eet Liquid Level Control Board Liquid d Transformer Level Probe Water Feed Solenoid 1 TO AVOID EQUIPMENT DAMAGE DO NOT CONNECT POWER SUPPLY Knock Out DIRECTLY TO ELEMENTS Field Wiring _ Water Feed 2 L1 L2 Ground to be field wired _ AutoFlush Plug and Play Connection see page 14 Steam Outlet 3 Super 1E 240 1 models are not supplied with internal fusing Models MS 90E MS 40 single phase wiring shown 4 All Drawings are for illustrative purposes only Consult with qualified licensed electrician for electrical installation Liquid Level Probe Power Block Fuses Liquid Level Control Board 3 Contactor Transformer Power Supply Illi r Knock Out A Water Feed Solenoid Field Wiring Water Feed AutoFlush Plug and _ Play Connection see page 14 Steam Outlet Models MS Super 1E 6 single phase wiring shown 9 Inf steam Installation Operation amp Maintenance Manual SINGLE PHASE 208 240 VOLT WIRING DIAGRAMS POWER INPUT L1 L2 o d LEGEND All Diagrams 7 WIRING BEU FIELD 3 E WIRING BLACK J OKL MODELS MS90E MS150E MS225E MS400E FACTORY WAT
14. and allow tank to fill with water 2 Turn off Mr Steam control Water should stay in tank 3 Turn off power at the panel box Water should discharge from tank 4 Turn on power at panel box 9 Repeat iN CAUTION PROVIDE DRAIN PLUMBING ACCORDING TO LOCAL All drawings are for illustrative purposes only CODES PLUMB AS REQUIRED FOR AUTOFLUSH SYSTEM TT steam Installation Operation amp Maintenance Manual OPTIONAL DRIP PAN Mr Steam strongly recommends the use of a drip pan in the unlikely event of a plumbing leak Locate the drip pan on a solid level surface and place the steam generator inside the drip pan Insure the steam generator is level see page 4 for locating the steam generator All plumbing shall be performed by a qualified licensed plumber and in accordance with applicable national and local codes Check local plumbing code for receptor trap and vent requirements Drip pans drain by gravity The drip pan is equipped with an integral female JA NPT fitting OPTIONAL EXPRESS STEAM only available factory installed Available for all MS Models Express Steam genera tors are equipped with a low power heating element and thermostat to keep the water in the tank warm enough to bring up steam quicker All Express Steam components and wiring are installed at the factory No additional wiring or plumbing is required by installers All drawings are for illustrative purposes only Inr steam Installation
15. homeowner Do not dis card this document The following general information should be used in conjunction with consultations with an architect designer and contractor in determin or service by unqualified persons or failure to use Mr Steam parts ing factors necessary in providing a suitable and safe steam room may result in property damage or in a hazardous condition e The MS series of steam generators are for residential use only Commercial or other nonresidential applications void the warran ty and may adversely affect product performance and may repre sent a safety hazard Mr Steam steam generators are intended to be operated with Mr Steam iSteam iTempo Plus iTempo Home Wizard and iGeniee controls only and are to be installed strictly in accordance with the specific instructions contained in this manual and as supplied in the manuals provided with the controls or accessories 3 mr steam WATER QUALITY INFORMATION For optimum results the water supply should be tested prior to installation If the mineral content exceeds the following recommended limits various external treatment processes are recommended to correct the problem NOTE An analysis of the on site water must be made by a recognized and reliable water treatment company to ascertain the existing condition and treatment required Poor water quality can affect efficiency or result in steam gen erator damage Water contains impurities in solution a
16. the desired time 1 60 min utes Press CANCEL to return to the Dashboard without changing or SAVE to save the new time 20 MINUTES Controls Set Temperature Screen Press the temperature on the Dashboard to ac cess the Set Temperature screen Swipe your finger to select the desired tem perature 80 120 degrees F Press CANCEL to return to the Dashbaord without changing or SAVE to save the new temperature The temperature units F C will automatically adjust to the setting of iSteam 2 0 110 FAHRENHEIT Accessories Music Press the MUSIC button Ja to access the music screen 144 Previous Track PHT Play Pause Pb Next Track Use the slider to adjust Volume The iSteam 2 0 app can be used to play the music stored in your device Start the music in your pre ferred music player and then navigate to the iSteam 2 0 app The App will display the track name iPhone and iPad users will also be able to view their album art AromaSteam Y The AromaSteam is an optional accessory that automatically infuses aromatic oils into the steam flow Press the AROMA button to turn it ON The AromaSteam turns OFF automatically when the steam generator stops Press the AROMA button to turn it OFF during a steam session ChromaSteam 9 The ChromaSteam is an optional accessory that activates colored lights in the steam room Press the CHROMA button to turn it ON Turn the button OFF then back ON to s
17. the Mr Steam control s intended use and function e Do not use the iSteam 2 0 control without reading and understanding the Mr Steam steam generator Installation and Operation Manual PN 100472 A peel and stick warning sticker is provided in the Mr Steam steam generator Installation Operation and Maintenance Manual This manual is provided with every steam generator The warning sticker must be read and permanently affixed in a conspicuous lo cation near the steam room Failure to read and affix this warning sticker in a conspicuous location may result in serious injury or death Please call Mr Steam at 800 767 8326 for a free replacement or if you have any questions regarding the warning sticker e f an iSteam 2 0 control is installed outside the steam room a Remote Temperature Probe PN iMSTS must be installed inside the steam room per installation instructions supplied with the Remote Temperature Probe Failure to install according to instructions will result in an inoperative control and overheating of the steam room WARNING REDUCE THE RISK OF OVERHEATING AND SCALDING 1 EXIT IMMEDIATELY IF UNCOMFORTABLE DIZZY OR SLEEPY STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING 2 CHILDREN UNDER THE AGE OF 16 SHOULD NOT USE THE STEAM BATH 3 CHECK WITH A DOCTOR BEFORE USE IF PREGNANT DIABETIC IN POOR HEALTH OR UNDER MEDICAL CARE 4 BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL DRUGS O
18. 5 Connect each end to the printed circuit board as shown 5 Connect separate plumbing and power supplies for each unit AutoFlush rol AutoFlush e e e Wiring Diagram MS Super 4E MS Super 5E MS Super 6E LEG EN D Al Dingras FIELD dd WIRING FACTORY PRIMARY UNIT SECONDARY UNIT WIRING POWER INPUT POWER INPUT L1 L2 G _ L1 12 G __ TT T TRANSFORMER T N rT TRANSFORMER BLACK AE BLUE BLACK AIL BLUE BLACK oA BLACK s a s FUSES WHT BLUE Sy pee L EN qe SS dc do FEED SOLENOID SOLENOID o v vx VALVE o v VALVE RED WHT GRAY WHT GRAY WHT RED WHT RED optional DEE o optional iTempo Start optional Do Not V V Connect TO PROBE iSteam or TO PROBE D Control HEATING ELEMENT iTempo Plus HEATING ELEMENT For connecting more than 2 steam generators in tandem POWER INPUT PRIMARY UNIT POWER INPUT SECOND UNIT AutoFlush optional Steam Genie optional EE Steam or TO PROBE iTempo Plus HEATING ELEMENT CONTACTOR ew PURPLE O O U TO PROBE HEATING ELEMENT PLUG THIS END TO MASTER UNIT CONTROL BOARD CONTROL BOARD Optional Tandem Cable for 2 5 Generators Length is 30 ft PN 103917 TT steam Installation Operation amp Maintenance Manual INITIAL START UP AND CHECKOUT Turn on control Follow specific instructions provided with controls ND Steam will begin to appear in a
19. 8 6 F The symptoms of hyperthermia include an increase in the internal temperature of the body d dizziness lethargy drowsiness and fainting The effects of hyperthermia include c Unawareness of impending risk Fetal damage in pregnant women e Physical inability to exit the steambath and f Unconsciousness NAAN The use of alcohol drugs or medication can greatly increase the risk of hyperthermia Designed Engineered and Assembled in the QU CE Usa LISTED PUR 100472A Rev 3 15 Inr ste ATN e sussman Automatic Corporation hello mrsteam com www mrsteam com 43 20 34th Street Long Island City NY 11101 TEL 1 800 76 STEAM Fax 718 472 3256 9410 S La Cienega Blvd Inglewood CA 90301 TEL 1 800 72 STEAM Fax 310 216 2944 RESIDENTIAL STEAMBATH GENERATOR SYSTEMS MODEL S INSTALLATION OPERATION amp MAINTENANCE MANUAL MODELS MS 90E MS 150E MS 225E MS 400E MS SUPER 1E SERIAL NO MS SUPER 2E MS SUPER 3E MS SUPER 4E MS SUPER 5E MS SUPER 6E TABLE OF CONTENTS Important Safety Instructions Inside front cover Select Your Mr Steam Model ss eee eee 2 Generator Specification Chart 0 0 cee eee eee 2 INSTALLER SECTION Before Installing ea EED HERE EE ER BEEBE de oR 3 Steam Room Guidelines EE SS sk ee 3 Water Quality Information llle 4 Locating the Steam Generator 0 0 0 0 cee eee 4 Typical Installation Instructions
20. ALLATION PLUMBING All plumbing shall be pertormed by a qualified licensed plumber and in accordance with applicable National and local codes 1 Use unions on all pipe connections 2 Use only brass piping or copper tubing as permitted by codes 3 DO NOT use black galvanized PVC pipe or PEX WATER SUPPLY Ys NPT 1 Connect to cold water line 2 Provide a shut off valve in the water supply line upstream of the steambath generator 3 DO NOT overheat inlet solenoid valve with solder connections Overheating will damage parts 4 Flush inlet water line thoroughly before making connection to unit 5 Strainer recommended upstream of teed water connection 6 For best pertormance water pressure should be 15 to 20 psig Reduce pressure as required 7 Provide anti water hammer device as required 8 Install an approved backflow preventer as required by local codes DRAIN 12 NPT NANKIN The drain from the generator should not share an undersink trap unless the generator is mounted higher than the sink to prevent damage to the generator if the drain backs up NOTE A drain valve is provided to facilitate servicing Provide a drain line connection from steambath generator drain valve according to National and local Codes Check local plumbing code for receptor trap and vent requirements Do not connect Drain line and Safety Valve line together Unit drains by gravity DO NOT connect the drain valve to the steam line STEAM OUTLET
21. Drawings for illustrative purposes only Consult with qualified designer architect or contractor for steam room construction details iSteam iTempo temperature sensor Locate the control in a location de or ilempo Plus representative of the desired steambathing temper atures Do not locate the control above or near the steam head or direct steam emissions b Ri H Control Refer to Control 1 Installation Manual __ for installation u information IN l Provide unions as required to facilitate installation and disconnect of piping Field installed Field installed water supply line power supply Drain Valve must be closed when the optional AutoFlush is not installed Field installed Steam supply pipe JN CAUTION To avoid unintentional steambath operation do not locate the control When installing the optional AromaSteam install a down where other controls accessories shower heads valves body sprays or similar within the ward facing 90 degree T in the steam supply line See the shower could cause confusion or interfere with the Mr Steam control s intended use and function AromaSteam Installation Manual for complete information TYPICAL INSTALLATION INSTRUCTIONS FOR MODELS MS SUPER 4E 5E amp 6E shown with optional AutoFlush Printed Circuit Board Component shown enlarged for illustrative purpose 1 Install each steam generator as in a single instal
22. ER FEED SOLENOID VALVE WHT GRAY WHT RED CONTACTOR AutoFlush PURPLE SteamGenie or iGenie optional V iSteam iTempo HEATING ELEMENT TO PROBE or iTempo Plus Control POWER INPUT MODELS MS SUPER 1E L1 2 G MS SUPER 2E EN po MS SUPER 3E Note Super 1E 240V does not have fuses SOLENOID AutoFlush CONTACTOR PURPLE SteamGenie or iGenie optional iSteam iTempo or iTempo Plus HEATING ELEMENT CONTROL BOARD Control THREE PHASE 208 240 VOLT WIRING DIAGRAM POWER INPUT MODELS MS90E MS150E MS225E MS400E MS SUPER 1E EL L2 Eg MS SUPER 2E d L3 G D a MS SUPER 3E SOLENOID WHT RED CONTACTOR o JOF AutoFlush optional PURPLE o o SteamGenie or HEATING ELEMENT TEN iSteam iTempo Inr steam Installation Operation amp Maintenance Manual INSTALLATION INSTRUCTIONS FOR MODELS MS SUPER 4E MS SUPER 5E AND MS SUPER 6E 1 Install each unit as in a single installation Install the two generators as close to each other as possible 2 ANWZEGOINT Shock Hazard Power must be disconnected at the main electrical supply before removing steam generator covers 3 Connect the iSteam or iTempo Plus control to either generator per the control instructions 4 Remove one knock out on each generator as shown Insert the ends of interconnecting cable provided PN 103904 through the knock outs as shown in the Diagram on page
23. N if the generator is ON FORCE ON Press this button to operate the generator This button is for trouble shooting only and will operate TEST BUTTON if a control is connected or not Pressing the button again will shut the generator OFF The test button will only allow the generator to operate for 10 minutes Liquid Level Control Board PN 103975 shown without wiring Te Dane BESS All drawings are for illustrative purposes only Force On Test Button TT steam Installation Operation amp Maintenance Manual OPTIONAL AUTOFLUSH Box Contents x Steam Generator 3 Pin Connector AutoFlush Valve with Cord ao uf for AutoFlush Installation Instructions OPERATION The optional AutoFlush System feature automatically drains the Mr Steam generator following each use A time delay allows the water to cool down about two hours before it drains by gravity for a safe and gentle operation E AutoFlush Cord Connector NOTE If the Express Steam option has been installed the AutoFlush will drain for ten minutes then refill with fresh water aa EA Nipple copper or brass to begin the pre neat cycle nipple 5 NPT x 314 or AutoFlush Cord Arun INSTALLATION INSTRUCTIONS 1 Plumbing to be performed by a qualified plumber and shall be in j K i Drain Valve ti n Plumb to accordance with applicable national and local codes Unit drains shown in the correct J Drain Line by gravity A drain line that i
24. R MEDICATION IS CAPABLE OF CAUSING UNCONSCIOUSNESS 3 DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD REDUCE THE RISK OF SLIPPING AND FALL INJURY 1 USE CARE WHEN ENTERING OR EXITING THE STEAM ROOM FLOOR MAY BE SLIPPERY NOTE FOR ADDITIONAL SAFETY CONSIDERATIONS SEE OWNER S MANUAL s s WHICH IS KEPT Py THE OWNER S MANUAL CAN BE FOUND AT WWW MRSTEAM COM OR BY SCANNING THE QR CODE USE OF STEAM ROOM IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL CAN BE DANGEROUS AND CAN RESULT IN INJURY THROUGH SLIP AND FALL OR OTHERWISE IMT SCE AT 43 20 34th Street Long Island City NY 11101 180076 STEAM w ALLES com Controls NEU Do not route iSteam 2 0 control wiring inside conduit together with power lines or close to hot water or steam piping Doing so may result in an inop erative or hazardous installation Do not alter or modify any Mr Steam products including the steam generator or iSteam 2 0 control Doing so may result in an inopera tive or hazardous installation and will void the warranty IMPORTANT NOTES e The iSteam 2 0 Control is designed to be flush mounted However the control may be surface mounted when conditions permit Consult a MrSteam Customer Service or Technical Service representative to determine if the iSteam 2 0 control can be surface mounted e Turn power to the steam generator OFF before connecting the control to the generator Failure to turn the power off will result in an inoperable control
25. STEAM or hello mrsteam com WARNING REDUCE THE RISK OF OVERHEATING AND SCALDING 1 EXIT IMMEDIATELY IF UNCOMFORTABLE DIZZY OR SLEEPY STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING 2 CHILDREN UNDER THE AGE OF 16 SHOULD NOT USE THE STEAM BATH 3 CHECK WITH A DOCTOR BEFORE USE IF PREGNANT DIABETIC IN POOR HEALTH OR UNDER MEDICAL CARE 4 BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL DRUGS OR MEDICATION IS CAPABLE OF CAUSING UNCONSCIOUSNESS 5 DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD REDUCE THE RISK OF SLIPPING AND FALL INJURY 1 USE CARE WHEN ENTERING OR EXITING THE STEAM ROOM FLOOR MAY BE SLIPPERY NOTE FOR ADDITIONAL SAFETY CONSIDERATIONS SEE OWNER S MANUAL req WHICH IS KEPT E EE THE OWNER S MANUAL CAN BE FOUND AT WWW MRSTEAM COM OR BY SCANNING THE QR CODE USE OF STEAM ROOM IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL CAN BE DANGEROUS AND CAN RESULT IN INJURY THROUGH SLIP AND FALL OR OTHERWISE Inr Stealmn 43 20 sete Street Lang Island City MY 1110L 180078 STEAM www mretBam pom PURLODOTA 7 18 Not Actual Size NANKIN if acrylic fiberglass or other non heat resistant mate rials are used as part of the steam room enclosure Consult with the material manufacture and see pg 7 Installing the Steamhead for additional details IMPORTANT NOTES This document contains important safety operation and maintenance information Leave this document with the
26. Sizing SteamStart SteamStop and The Intelligent Steambath are trademarks of Sussman Automatic Corporation PUR 100489 A REV 2 15 Inr steam Optional Autoflush System BOX CONTENTS e AutoFlush System Valve with Cord e Installation Instructions ASSEMBLY OF OPTIONAL AUTOFLUSH SYSTEM ms IE u P3 a End BY T F T Plumb to Steam Generator Drain Valve End ip shown in the correct open position Nipple lt DO NOT REMOVE THIS DRAIN VALVE copper or brass nipple po 1 2 NPT x 90mm or Arrow indicates correct 1 2 NPT x 3 1 2 or direction of flow longer not supplied Drain Line OPERATION The optional AutoFlush System feature automatically drains the Mr Steame system following each use A time delay allows the water to cool down about two hours before it drains resulting in a safe and gentle operation PUR 100200 Rev 5 13 Inf Stealn sussman Automatic Corp hello mrsteam com www mrsteam com 43 20 34th Street Long Island City NY 11101 tel 1 800 76 STEAM fax 718 472 3256 9410 S La Cienega Blvd Inglewood CA 90301 tel 1800 72 STEAM fax 310 216 2944 INSTALLATION INSTRUCTIONS 1 Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes Unit drains by gravity A drain line that is lower than the AutoFlush assembly must be available The AutoFlush System valve outlet is threaded 1 2 NPT Check plumbing code for receptor trap an
27. ays be followed including the following IMPORTANT SAFETY INSTRUCTIONS of potential hazards that may occur during installation and operation NOTA indicates a potentially 2 AGI Do not permit children under 1 READ AND FOLLOW ALL INSTRUCTIONS the age of 16 to use this steambath M WARNING Steam is hot and can cause injury or death if improperly used Steam rooms contain D Excessive temperatures have a high potential for causing fetal damage dur ing the early months of pregnancy Pregnancy or possibly pregnant women hazardous situation which if not avoided could result in death or serious injury TT indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury or A product damage in steam and elevated temperatures Please read and observe all warnings in this manual before stalling or using a steam room 4 To reduce the risk of injury The wet surfaces of steam enclosures may be slippery Use care when entering or leaving B The steam head is hot Do not touch the IMPORTANT NOTE This highlights information that is especially relevant to a problem free installation All information in these instructions is based on the latest product information available at the time of publication Sussman Automatic Corporation reserves the right to make changes at any time without notice HYPERTHERMIA occurs when the internal tem perature of the body reac
28. c or any locations where water could freeze and cause pipes to rupture and cause property damage 6 Install steambath generator on a solid and level sur face Keyhole slots are provided for wall mounting result in an inoperative or hazardous installation Insure the steam generator is properly secured and level when mounting with keyhole slots to prevent damage to the steam generator 7 Install steambath generator in an upright position only to prevent damage to the generator IMPORTANT NOTES Items 8 11 8 Install anti water hammer device as necessary 9 Provide a minimum of 12 inches at both ends and top of the steam generator or as required for servicing See page 8 10 Provide unions as required to facilitate installation and disconnection of piping 11 Mr Steam controls can be located inside the steam room or on the outside of the steam room See the Control Installation Manual for your specific control package for specific details 12 The MS series of steam generators are for residential use only Commercial or other nonresidential applications void the warranty and may adversely affect product per formance and may represent a safety hazard NOTE Mr Steam Generators inclusive of the iTempo and iSteam series Controls are CE and UL listed Suitable for operation in ambient not exceed ing 45 C 113 F mr steam Installation Operation amp Maintenance Manual TYPICAL MR STEAM INSTALLATION NOTE
29. d vent requirements 2 Use copper or brass nipple 1 2 NPT x 90mm or 1 2 NPT x 3 1 2 or longer not supplied to connect AutoFlush valve end B to the Drain Valve valve end A and B are indi cated on bottom of AutoFlush Valve DO NOT REMOVE THE DRAIN VALVE Removal may cause equipment and property damage If there is not enough room for the valve an elbow and a short nipple not provided can be added 3 Open Drain Valve handle must be aligned with brass nipple 4 Connect the AutoFlush System cord connector to the three pin connector as shown Do not drain into a steam enclosure or any loca tion where accidental contact with drain water may occur In the event of a power failure the AutoFlush System valve will open and may discharge boiling water SWEAT FITTINGS When using sweat fittings use only tin base solder with a melting point below 600 degrees F Do not overheat Ends of water sup ply tubing must be thoroughly clean for a minimum distance of 1 from ends Do not remove valve cover TO CHECK OPERATION 1 Turn on Mr Steam and allow tank to fill with water see Mr Steam instruction manual 2 Turn off Mr Steam control Water should stay in tank 3 Turn off power at the panel box Water should discharge from tank 4 Turn on power at panel box 5 Repeat PROVIDE DRAIN PLUMBING ACCORDING TO LOCAL CODES PLUMB AS REQUIRED FOR AUTOFLUSH SYSTEM IMPORTANT NOTE Contact the Mr Steam Technical Service
30. e screen on iSteam 2 0 after Wi Fi has been enabled Press the appropriate iSteam 2 0 you want to control Passcode Enter the passcode that was set on the iSteam 2 0 when the Wi Fi was enabled in the passcode screen and press ENTER Start Screen Press the START button to turn the steam genera tor ON and to display the Dashboard screen Steam will begin to flow a few min utes after the START button Is pressed and the warnings are read The time required for the steam room to reach steam bathing tempera ture depends on the steam room construction and steam generator specifications mr steam User Settings Pressing the USER 1 USER 2 or USER 3 but ton before pressing the START button will auto matically load the user settings User 1 and User 2 settings are stored in iSteam 2 0 and cannot be adjusted trom the App User 3 settings are stored in the app To adjust the User 3 settings press and hold the USER 3 but ton The User 3 setting screen will open press the parameter you wish to adjust To accept the adjust ments press SAVE use the CANCEL button to close without making changes Dashboard Screen The Dashboard displays key steam bathing features and optional accessories In one convenient screen including TIME SET POINT TEMPERATURE ROOM TEMPERATURE ChromaSteam and AromaSteam status Set Timer Screen Press the time on the Dashboard to access the Set Timer screen Swipe your finger to select
31. e should be opened fully flushing out accumu lated materials salts and other particles which are natural by products of boiling water INSIST Flush a minimum of two three hours after the con trol has been turned off to insure that the water has cooled Draining immediately after a steam cycle may expose PVC and other piping to high temperature water Check local codes The unit will refill automatically when the control is activated again In areas of hard water a Mr Steam AutoFlush system is recommended for generator longevity NQESIING Failure to allow the water to cool will expose the equipment and user to scalding water and cause property and personal injury mr steam USING MR STEAM ESSENTIAL OILS Enjoy AromaSteam essential oils by placing a drop or two into an unheated AromaSteam steamhead as shown in the illustration Only use Mr Steam AromaSteam essential oils in the Mr Steam AromaSteam steamhead ANQZS XIN Essential oils and or aroma therapy can cause inflammation burns headache nausea and allergic reactions Consult a physician before using aroma therapy 1 Use essential oils with caution Essential oils are for exter nal use only Keep out of reach of children Essential oils are highly concentrated and are potent substances and should not be applied directly to the skin as they can be irritants Use essential oils with caution 2 Place the drops into the Mr Steam AromaSteam steamhead recess prior
32. eating Element 7 5 KW 240V MS 225E 29091BMS Heating Element 9 KW 208V MS 400E 29091CMS Heating Element 9 KW 240V MS 400E 29101BMS Heating Element 10 KW 208V MS SUPER 1E amp MS Super 4E 29101CMS Heating Element 10 KW 240V MS SUPER 1E amp MS Super 4E 29121BMS Heating Element 12 KW 208V MS SUPER 2E amp MS Super 5E 29121CMS Heating Element 12 KW 240V MS SUPER 2E amp MS Super 5E 29151BMS Heating Element 15 KW 208V MS SUPER 3E amp MS Super 6E 29151CMS Heating Element 15 KW 240V MS SUPER 3E amp MS Super 6E 104058 iGenie All Models 104059 iGenie Interface Module All Models 104060 iGenie Interface Cable 5 ft All Models mr steam CONTROL INSTALLATION Installation Operation amp Maintenance Manual Refer to Control Manual for specific installation requirements BEFORE INSTALLING Turn power to the steam generator OFF before connecting the control to the generator Failure to turn the power off will result in an inoperable control To avoid unintentional steambath operation DO NOT locate the control where other controls acces sories shower heads valves body sprays or similar within the shower could cause confusion or interfere with the Mr Steam control s intended use and function DO NOT use any iSteam iTempo Plus iTempo HomeWizara or iGenie controls without reading and understanding its own manual and the Mr Steam steam generator Installation and Operation Manual Failure to read and understand these
33. eatures an integral temperature sensor Locate the control in a location representative of the desired steambathing temperatures DO NOT locate the control above or near the steam head or direct steam emissions 4 on a vertical wall The control cable length is 30 feet Insure that the control and or steam generator are located accordingly An optional 60 foot cable is available PN 103990 60 for iTempo and PN 104117 60 for iSteam Contact a Mr Steam technical service representative if a 60 foot cable is required Excess control cable should be neatly coiled and twisted into a figure 8 IMPORTANT NOTES e f the control is installed outside the steam room a Remote Temperature Probe Part Number MSTS or iMSTS must be installed inside the steam room depending on the control e Insure Mr Steam steam generator is isteam or iTempo com patible and has a serial number 900000 or higher If iSteam is used with a generator having serial number 900000 through 930030 contact Mr Steam technical support for an upgraded PC board See instructions for the MSTS or iMSTS Temperature Probe located in the Control Installation Manual related to your specific control package before rough in or installation of control mr steam Installation Operation amp Maintenance Manual HOMEOWNER SECTION READ ME FIRST NWSI As you follow these instructions you will notice warning and caution symbols This blocked information is important f
34. ectrical code 240 i 208 1 29 8 8 POWER WIRING MS 150E 150 6 0 3 17 10 10 See Field Power Wiring Diagrams below 240 1 25 8 8 3 14 12 12 1 Check power voltage Use 240V rated unit when supply EE T is greater than 208V Most homes have 240V 1PH MS 225E 225 75 3 21 10 10 service Use 208V rated unit for 208V power 240 1 32 8 8 E 3 18 10 10 2 Use minimum 90 C 300V rated insulated copper TAE T conductors only sized in accordance with National MS400E 360 90 3 25 9 9 Electrical Code and local electrical code for the current 240 1 38 8 8 in Ampere Chart If allowed by codes NM cable may 3 22 10 10 require a larger wire size than as listed on the chart 208 1 49 6 6 MS Super 475 10 0 3 20 8 8 3 Connect suitably sized equipment grounding wire to 1E 240 1 42 g b ground terminal provided 3 24 8 8 4 Install a separate circuit breaker between supply and i p P PPI MS Super 575 120 3 34 8 8 unit Provide a power supply disconnect within sight 2E 240 1 50 b 7 of the steam generator or one that is capable of being 3 29 8 8 locked in the open position 208 1 73 4 3 MS Super 675 15 0 3 42 8 6 5 For single phase units use two wire supply source and 3E 240 1 63 4 4 equipment grounding wire Neutral white wire is not 3 36 8 8 required See page 2 for room sizing tAll specifications shown are for 208V and 240V Consult factory for other voltage specifications WARNING PROVIDE A POWER
35. elect the desired color Press again to turn the lights OFF mr steam Care Tips Use only mild soap and water on a soft cloth to clean the control Do not use abrasive cleansers Safety and Operating Information Set the steam bathing duration and tempera ture according to personal preference however it is highly recommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels Set the duration at 10 minutes max to gauge comfort and safety levels This will allow the steam generator to heat up and begin produc ing steam Do not use any iSteam 2 09 control without reading and understanding the Mr Steam steam generator Installation and Operation Manual PN 100472 Failure to read and understand these instructions may result in an in operative or hazardous installation A peel and stick warning sticker is provided in the Mr Steam steam generator Installation Operation and Maintenance Manual This manual is provided with every steam generator The warning sticker must be read and permanently affixed in a conspicuous location near the steam room Failure to read and affix this warn ing sticker in a conspicuous location may result in serious injury or death Please call Mr Steam at 800 767 8326 for a free replace ment or if you have any questions regarding the warning sticker If an iSteam 2 0 control is installed outside the steam room a Remote Temperature Probe PN iMSTS must be installed in
36. erators are connected to 240V line voltage and contain live electrical components All installation and service to be performed by qualified and licensed electricians and plumbers only Installation Installation Operation amp Maintenance Manual the steambath room Pay particular attention to room volume and construction If any questions please refer to Mr Steam sizing and selection guide on page 2 3 Marble or glass walls or ceilings ENLARGE the room s size requiring a generator larger than one based only on the room s cubic foot L x H x W volume 4 The physical size of the unit clearance for plumbing servicing and its distance from the steam room must all be considered before final installation 5 Consider any controls and accessories before initiating installation Read the Installation and Operation Manual of all controls and accessories available at www mrsteam com technical downloads The peel and stick warning label located in this manual is an essential part of providing a safe environment for steam room users The peel and stick warning label must be applied to the wall of the shower or steam enclosure at a point that is visible to all users Failure to install this sticker may result in serious injury or death The location where this owner s manual is kept shall be written in the space provided on the label using per manent ink For a replacement warning label contact Mr Steam customer service at 1 800 76
37. ext Track connected for functions to work Please refer to the PP Bluetooth only Bluetooth pairing instructions in this manual Please note that the Play Pause and Change Track functions apply to Bluetooth only and will not work when playing audio from a hard wired music source a Increase Volume m Decrease Volume AromaSteam Y ChromaSteam 9 The ris The ChromaSteam is an optional accessory that ee ea A a on Into t o activates colored lights in the steam room Press ow Fress the utton to turn It ON the CHROMA button to turn it ON Turn the The AromaSteam turns OFF automatically when button OFF then back ON to select the desired color the steam generator stops Press the AROMA Press again to turn the lights OFF button to turn it OFF during a steam session mr steanY Controls Optional Accessories Screen ian eens Press the ACCESSORIES button on the START ACCESSORIES screen to access the optional ChromaSteam and AudioWizard accessories when a steam bath is not in session ChromaSteam See page 10 for information on the AudioWizard ChromaSteam and AudioWizard operation Settings Screen The Setting Screen allows access to less frequently used screens including the setting of DAY TIME DISPLAY BRIGHTNESS PASSCODE LOCK aa SYSTEM RESET and LANGUAGE Page 9 i rem 8 19 AM mr steam SETTINGS Settings gt Set Day Time umori Access the system SETTINGS screen by pressing the Prev
38. hase an optional 60 ft cable PN 103990 60 cement board or mortar bed for Tempo and PN 104117 60 for iSteam 3 Ceiling Height For each foot above 8 feet Add 15 4 Add all figures above to obtain the Total Room Volume required Compare your Room Volume to the Chart below and select the appropriate model e e e e e e e e eee RESIDENTIAL STEAM GENERATORS SPECIFICATION CHART Amps for Wire Total Adj Water Usage Shipping Model No KW 240v 1PH t Sizet Room Vol Gallonstt Dimensions Wt Ibs MS90E 5 21 10 100 067 14 Lx 14 Hx 6 D 30 MS150E 6 25 8 1 150 i 0 80 142 L x 1434 H x 6 D 30 MS225E 7 5 32 8 225 1 0 14 2 L x 14 4 H x 64 D 30 MS400E 9 38 8 1 360 1 2 MA Lx 14 Hx 6 D 30 I I I I MS SUPER 1E 10 42 8 475 1 4 17 Lx 18 H x 7 D 40 MS SUPER 2E 12 50 6 5S 1 6 17 Lx 18 H x 7 D 40 I I MSSUPER3E 15 63 4 1 695 20 17 Lx 18 H x 7 D 40 I I I I I I MSSUPER4E 20 84 8 1 875 i 27 17Lx185 Hx74 Dx2 80 I I I I MS SUPER 5E 24 100 6 1075 i 3 2 17 Lx 18 H x 74 D x 2 80 MS SUPER 6E 30 125 4 1275 4 0 17 Lx 18 H x 74 D x 2 80 I I I I IMPORTANT NOTES Dimensions are for generator only without e Add C1 suffix to Model No for 240V 1Ph Add B1 suffix to Model No for 208V 1Ph AutoFlush or plumbing features e Models SUPER 1E 6E must use iTempo Plus control Shipping weight and pricing are for generator only All Mr Steam MS Models are cULus Listed and CE approved wit
39. hes a level several degrees above the normal body temperature of 98 6 F The symptoms of hyperthermia include an increase in the internal temperature of the body dizziness lethargy drowsiness and faint ing The effects of hyperthermia include C steamhead and avoid the steam near the steamhead Prolonged use of the steam system can raise excessively the internal human body tempera ture and impair the body s ability to regulate its internal temperature hyperthermia Limit your use of steam to 10 15 minutes until you are certain of your body s reaction a b c Unawareness of impending risk Failure to perceive heat d Fetal damage in pregnant women e Physical inability to exit the steambath and f Unconsciousness Failure to recognize the need to exit the steambath should consult a physician regarding cor rect exposure Obese persons and persons with a history of heart disease low or high blood pressure circulatory system problems or diabetes should consult a physician before using a steambath Persons using medication should consult a physician before using a steambath since some medication may induce drowsiness while other medications may affect heart rate blood pressure and circulation SAVE THESE INSTRUCTIONS The use of alcohol drugs or medication can greatly increase the risk of hyperthermia Table of Contents Box Contents Important Safety Ins
40. hout control or steamhead W 20 mi f ion NOTES All MS Generators available in 240v 1PH 208v 1PH and other voltages phases TI Water usage Based AE ot operation t Amps are for 240 1PH rated units Wire size AWG based on minimum 90 C rated THHN copper conductors Refer to the National Electrical Code for other types of conductors See Mr Steam Installation and Operation Manual for complete dimensional and installation information MS SUPER 4E includes two MS SUPER 1E steam generators and require one iTempo Plus Control and two matching steamheads MS SUPER 5E includes two MS SUPER 2E steam generators and require one iTempo Plus Control and two matching steamheads MS SUPER 6E includes two MS SUPER 3E steam generators and require one ITempo Plus Control and two matching steamheads mr steam BEFORE INSTALLING Carefully inspect the Steam Generator and packaging for shipping damage In the event of shipping damage please contact the carrier for claim information Our customer service department can assist you with any missing or damaged parts Read these instructions before installation or service Although this MS steambath generator has been fully qualified for shipment by Mr Steame the following must be reviewed for proper safe and enjoyable steam bathing 1 Verify that the model and accessories specifications are correct for the incoming line voltage 2 Insure steambath generator has been correctly sized for
41. ime Press HOME to return to the Dashboard sav a ing the time for this steambath session only Press SAVE to F C TOGGLE save the time setting as the new default or as the selected be used the next time the control Oo ELE user setting is turned on If the control times out not manually turned off then the previous user Changing the Temperature Units F C time and temperature settings will be used when Press the UNITS button in the lower right corner of the steambath is used again the SET TEMPERATURE screen to change trom Fahr enheit to Celsius Press the SAVE button to User Preferences User1 and User2 accept the new value and exit Press USER 1 USER 2 button Enter the preferred time and temperature settings and press SAVE Memory Feature iSteam 2 09 will automatically save the settings If the control is turned off manually before it times out To recall the user preferences press USER 1 USER then the default settings of 20 minutes and 110 F will 2 the next time the steambath is used AudioWizard 2 0 iSteam 2 0 Interface Press the MUSIC button Jd to access the AudioWizard screen The AudioWizard will automatically turn on when audio is sent to it AudioWizard automatically enters sleep mode 2 minutes after music stops Previous Track 144 Bluetooth only s Return to Previous Screen gt Il e gt Bluetooth Pairing Bluetooth only 9 Button If you are using a Bluetooth audio source it must be i N
42. in an inoperable control 2 DO NOT operate iSteam iTempo Plus iTempo HomeWizard or iGenie controls with other than a Mr Steam iSteam or iTempo compatible steam generator Mr Steam residential steam generators with serial num bers lower than 900000 or any other brand of steam generator are not to be operated with iTempo controls Doing so may result in an inoperative or hazardous instal lation If iSteam is used with a generator having serial number 900000 through 930030 contact Mr Steam tech nical support for an upgraded PC board This document contains important safety operation and maintenance information Leave this document with the homeowner Do not discard this document 4 Discontinue use of the steam generator or control if the steam generator is damaged or otherwise not function ing properly Operating a damaged steam generator may result in an inoperative or hazardous installation Refer to Installation Instructions for the specific control IMPORTANT NOTE The control cable should be run in a dedicated 1 conduit to facilitate installation and service 1 Determine the desired installation location of the con trol The iSteam iTempo and iTempo Plus controls are designed to be installed inside or outside the steam room as a matter of personal preference If the control is in stalled inside the steam room the control must be located 2 4 5 feet above the floor near the bather seating area 3 The control f
43. ing the early months of pregnancy Pregnancy or possibly pregnant women should consult a physician regarding correct exposure injury or death if improperly used Steam rooms contain steam and elevated temperatures Please read and observe all warnings in this manual before installing or using a steam room E Obese persons and persons with a his tory of heart disease low or high blood 4 To reduce the risk of injury Y J pressure circulatory system problems A The wet surfaces of steam enclosures or diabetes should consult a physician may be slippery Use care when entering before using a steambath r leaving l N ee F Persons using medication should con B The steam head is hot DO NOT touch the sult a physician before using a steam steam head and avoid the steam near bath since some medication may the steam head induce drowsiness while other medica C Prolonged use of the steam system can raise tions may affect heart rate blood pres excessively the internal human body temper sure and circulation ature and impair the body s ability to regu late its internal temperature hyperthermia Limit your use of steam to 10 15 minutes until you are certain of your body s SAVE THESE INSTRUCTIONS reaction HYPERTHERMIA occurs when the internal temperature of the a Failure to perceive heat body reaches a level several degrees above the normal body b Failure to recognize the need to exit the steambath temperature of 9
44. instructions may result in an inopera tive or hazardous installation NANI A peel and stick warning sticker must be read and permanently affixed in a conspicuous location near the steam room Failure to read and affix this warning sticker in a conspicuous location may result in serious injury or death Install the iSteam iTempo or iTempo Plus controls according to installation instructions Failure to install according to instructions will result in an inoperative control or hazardous overheating or inadequate heating of the steam room If an iSteam iTempo or iTempo Plus control is installed out side the steam room a Remote Temperature Probe PN MSTS or iMSTS must be installed inside the steam room per instal lation instructions supplied with the Remote Temperature Probe Failure to install according to instructions will result in an inoperative control and overheating of the steam room CONTROL ROUGH IN DO NOT route iSteam iTempo Plus iTempo HomeWizard or iGenie control wiring inside conduit together with power lines or close to hot water or steam piping Doing so may result in an inoperative or hazardous installation DO NOT alter or modify any Mr Steam product Doing so may result in an inoperative or hazardous installation and will void the UL listing and warranty IMPORTANT NOTES 1 Turn power to the steam generator OFF before connect ing the control to the generator Failure to turn the power off will result
45. ional use of the steambath Enter a 4 digit passcode using the keypad Press the passcode lock Loj ojtoj o pogon button ON under the 4 digit code to turn the passcode lock on EE Press SAVE to store the passcode The next time the iSteam 2 0e control is turned on the user will be prompted to enter the pass code Press CANCEL to exit without storing the passcode lock mr steam Passcode Lock Enable WiFi AIEN CANCEL HOME SAVE If you forget your passcode power should be turned off at the cir cuit breaker After 1 minute turn the breaker back on The passcode lock will automatically be turned OFF To enable WiFi on your iSteam 2 0 so you can use the iSteam 2 0 app slide the Enable Wi Fi switch to ON AutoStart NIE AutoStart will automatically turn the steam gen 12 03 AM re erator on at your preset time Activating the steam in an occu AUTOSTART pied room may subject persons to the hazards described in this manual Only activate the steambath if the steam room door is closed Activating or using the steambath with an open door may cause property damage or injury to persons outside of the Ue E3 ES BE steam bath Ka The AutoStart feature can be used to turn on the steambath at a predetermined time Select the day s of the week and the time of day you would like to turn the steam bath on You can also set the ChromaSteam and AromaSteam to turn on To activate AutoStart slide the switch to the ON position and pres
46. ious screen Page 12 button on the start screen To set the TIME press the at es parameter HOURS MINUTES AM PM DAY to be l adjusted Use the UP DOWN arrows to change Press Set Day Time the SAVE button to save the time Press the CANCEL 7771 button to exit without saving the changes Press the MY EJ HOME button to return to the SETTINGS screen ET SUNDAY CANCEL HOME SAVE Settings gt Display Press to change from To adjust the screen brightness swipe your 12 to 24 hr a finger as shown The OFF screen can display the clock remain blank until touched or be 8 19 AM mr steam the START screen by using the buttons 9 to 10096 DISPLAY SETTINGS shown A screen saver can be DIM FULLY BRIGHT turned ON OFF using the DEE EIE button shown When ON the a display will automatically dim View when off std GENS Erg after it has been on for 1 hour screen Saver Occ fen Settings gt Language To change the language used in iSteam press ae the LANGUAGE button in the settings screen Select LANGUAGE the language you would like to use by taping it Press SAVE to confirm the language change mr steam CANCEL HOME SAVE mr steanyY Controls Settings gt Passcode The Passcode feature can help prevent unintentional use of the steambath Please refer to the steam generator AD Installation Operation and Maintenance manual PN 100472 before PASSCODE using the steam bath The Passcode feature cannot insure uninten t
47. l AudioWizard is used STEP 3 Line up the two TABS 3a on the right of the box against a stud These TABS help locate the box to sit PROUD of the stud 3b STEP 4 SCREW 4a the two supplied screws into the stud STEP 5 Route the CONTROL CABLE 5a through the back of the rough in box and clip it under one of the TABS 5b that previously held the screws The two ends of the control cable are the same Controls mr steanyY Controls Installation with Optional Rough In Box cont IMPORTANT NOTE Be careful not to strain staple pinch or otherwise damage the cables Route cables as required to permit replacement Do not route cables inside conduit together with power lines or close to hot water or steam piping STEP 6 When used route the AudioWizard Cable 6a through a second knockout in the rough in box and clip 6b The two ends of the AudioWizard cable are the same See the AudioWizard Installation Operation amp Maintenance Manual PUR 100478 for complete AudioWizard Installation instructions STEP 7 Use the rough in box as a guide to cut out the 3 x BA opening in the wall Rough In box used as o f aguidetocutoutthe Finish the iSteam 2 0 installation using the instructions on page 7 opening Installation without Rough In Box STEP 1 GET 9 H 1 H t 2 4 Make a 3 6 x 5 cut out in the desired location using the i template provided on page 2 of this manual STEP 2
48. lation Install genera tors as close as practical to each other not exceeding 10 feet The interconnecting cable length is 12 feet 2 AITSA Shock Hazard Power must be disconnect ed at the main electrical supply Remove steam gen erator covers Retain screws and covers for reuse iSteam or iTempo Plus Control Power M Supply Interconnecting 3 Connect the iSteam or iTempo Plus control to ZA Cable PN 103904 either unit as per the Installation Manual supplied with each control 4 Remove one knock out on each generator as shown Insert the ends of interconnecting cable provided PN 103904 through the knock outs as shown in diagram Connect each end to the printed circuit board connector labeled TANDEM as shown 5 Prevent the interconnecting cable from contacting hot surfaces such as steam outlet safety valve and the like Steam Heads shown with optional acrylic 6 Connect separate plumbing and power supplies T shields for each unit Replace covers with cover screws 7 Provide unions as required to facilitate installation and disconnection of piping Optional AutoFlush see AutoFlush Secondary Unit Installation page 14 NOTE The secondary unit will de energize when the steam room reaches steambathing temperature resulting in a more gentle and energy efficient operation All drawings are for illustrative purposes only TT steam Installation Operation amp Maintenance Manual INST
49. luded Drain Valve Stainless Steel Tank mr steam REPLACEMENT PARTS LIST Part No Description Generator 99178MS Drain Valve All Models 99297 Safety Valve 15PSI All Models 100479 Water Feed Solenoid Valve w filter All Models 10477 3 Transformer 24VAC All Models 103975 Liquid Level Control Board All Models 103904 Tandem Cable for 2 generators 12 ft All Models 103917 Tandem Cable for up to 5 generators 30 ft All Models 103990 30 Cable for iTempo Control 30 ft All Models 103990 60 Cable for iTempo Control 60 ft All Models 104117 30 Cable for iSteam 30 ft All Models 104117 60 Cable for iSteam 60 ft All models MSTS Remote Temperature Probe for iTempo Plus All Models IMSTS Remote Temperature probe for iSteam All Models 100476 2 Contactor 50A 2 pole MS 90E 400E Single phase 29012 Contactor 50A 3 pole All 3 Phase Models 103453 Contactor 50A 4 pole MS Super 1E Super 6E 100471 2 Probe Assembly All Models 99096MS Heating Element Gasket All Models 103938 Round Acrylic Shield iTempo amp iTempo Plus All Models 103938 Square Acrylic Shield iTempo amp iTempo Plus All Models Installation Operation amp Maintenance Manual 99314 Power Fuse 60A 250V MS Super 1E 6E Single phase 29051BMS Heating Element 5 KW 208V MS 90E 29051CMS Heating Element 5 KW 240V MS 90E 29061BMS Heating Element 6 KW 208V MS 150E 29061CMS Heating Element 6 KW 240V MS 150E 29071 BMS Heating Element 7 5 KW 208V MS 225E 29071 CMS H
50. m FDD IMPORTANT NOTE A Wi Fi network is required to use the iSteam 2 0 App If you cannot connect to your iSteam 2 0 the Wi Fi sig nal may be too weak The wireless router can be moved closer to the iSteam 2 0 control or a wireless repeater can be installed near the iSteam 2 0 control Open the iSteam 2 0 app and press CONFIGURE iSTEAM WIRELESS Ensure the SSID listed is the name of your Wi Fi network If the SSID is different from your network or no SSID is listed ensure Wi Fi is enabled on your de vice If your wireless network is password protected enter the password in the location provided Press CONFIGURE NOW When iSteam 2 0 is properly configured the app will re turn to the Configure Search Demo screen If an error occurs ensure the Wi Fi has been enabled on iSteam 2 0 you are in the proper wireless network your password is correct and the wireless signal at the iSteam 2 0 is strong Controls IMPORTANT NOTE Only one smart device can control iSteam 2 0 at a time To use more devices the App must be closed on all other device To use iSteam 2 0 from another device simply press search for iSteam 2 0 after the iSteam 2 0 has been configured Configuring the iSteam 2 0 only needs to be done once Search for iSteam After configuring iSteam 2 0 press SEARCH OF iSTEAM UNITS Your iSteam 2 0 will be displayed as iSteam XX XX The 4 digit code will match the last 4 digits of the MAC address displayed in the passcod
51. medication may induce drowsiness while other med ications may affect heart rate blood pressure and circulation SAVE THESE INSTRUCTIONS REDUCE THE RISK OF OVERHEATING AND SCALDING 1 EXIT IMMEDIATELY IF UNCOMFORTABLE DIZZY OR SLEEPY STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING 2 CHILDREN UNDER THE AGE OF 16 SHOULD NOT USE THE STEAM BATH 3 CHECK WITH A DOCTOR BEFORE USE IF PREGNANT DIABETIC IN POOR HEALTH OR UNDER MEDICAL CARE 4 BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL DRUGS OR MEDICATION IS CAPABLE OF CAUSING UNCONSCIOUSNESS 5 DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD REDUCE THE RISK OF SLIPPING AND FALL INJURY L USE GARE WHEN ENTERING OR EXITING THE STEAM ROOM FLOOR MAY BE SLIPPERY NOTE FOR ADDITIONAL SAFETY CONSIDERATIONS SEE OWNER S MANUAL ofe WHICH IS KEPT 4 THE OWNER S MANUAL CAN BE FOUND AT WWIW MRSTEAM COM s OR BY SCANNING THE QR CODE T USE OF STEAM ROOM IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL CAN BE DANGEROUS AND CAN RESULT IN INJURY THROUGH SLIP AND FALL OR OTHERWISE MYT SCE AM 43 20 34th reet Long and City NY LLIGI 1800 76 STEAM ww this manual is an essential part of providing a safe envi ronment for steam room users The peel and stick warning label must be applied to the wall of the shower or steam enclosure at a point that is visible to all users Failure to install this sticker may result in serious injury or death
52. n considering the purchase or Mr Steam Your Fingertips use of this steambath system please note that if Start working smarter with Mr Steam s mobile sizing app you are pregnant have a coronary condition are now available for the iPade iPode and most smart phones in poor health are being treated for any other medical condition or are using medication or Visit mrsteam com to size your generator automatically drugs Mr Steam recommends that you obtain or go directly to http isizing mrsteam com the approval of a physician before use For information about this product and safety issues please call 1 800 76 STEAM Materials of construction room size and special design features such IMPORTANT NOTES as large glass areas all affect the steam generator model selection For steam rooms constructed of acrylic or synthetic materials select next lower rated 1 Measure length width amp height in feet of the steam shower or tub shower MS model Multiply the Length _ x Width x Height ROOM VOLUME The Mr Steam Sizing Chart allows for up to 60 feet of insulated steam line from the MS genera 2 Construction Materials tor to the steam room If the 60 foot line is exceeded consult with factory The steam genera For natural stones natural marble Add 110 tor control locations must be taken into account stone shale glass block or concrete A 30 foot cable is standard Contact Mr Steam to For ceramic or porcelain tile on Add 40 purc
53. nce Manual PUR 100478 for complete AudioWizard Installation instructions Turn the generator on and test the control and AudioWizard when installed to verity correct con nection With proper function proceed to Step 2 Optional AudioWizard For illustrative purposes only mr steam Controls Installation Instructions for iSteam 2 0 cont STEP 2 Peel the double stick adhesive off the back of the iSteam 2 0 control 2a Apply a bead of silicone around the rear of the iSteam 2 0 control to create a moisture seal 2b Carefully feed the cables into the rough in box and secure the control to the wall Care must be taken to not pinch the cables Ensure the control is level IMPORTANT NOTE The iSteam 2 0 control display reads in one direction only The control must be in stalled with the arrow on the Peel Off screen protector facing up If the Peel Off screen protector has been removed see the drawing in Step 2b for the proper orientation NOTE The silicone supplied by Mr Steam can be used to meet a variety of sealing and gasketing It cures to silicone rubber and adheres to glass wood metal porcelain ceramictile painted surfaces many plastics and rubber Surfaces must be clean and dry Apply thin layer of product Fit together and support if necessary Allow excess material to cure then trim with a sharp blade Sealant skins in 5 minutes dries to touch in 1 hour Fully cures and bonds in 24 h
54. nd sus pension These impurities concentrate in the generator The concentration of these impurities increases as more feedwater is introduced into the generator and steam is produced If the suspended solids are allowed to concentrate beyond certain limits a deposit or scale will form on the generator internal surfaces This deposit can interfere with the proper generator operation and cause generator failure The concentration of these impurities is generally controlled by the water quality and by periodic draining of the generator LOCATING THE STEAM GENERATOR Select a location as near as practical to the steam room Installation Operation amp Maintenance Manual RECOMMENDED FEEDWATER QUALITY Hardness ppm 8 85 0 5 5 gpg P Alkalinity ppm 85 410 5 24 gpg T Alkalinity ppm 200 500 7 0 gpg pH strength of alkalinity 8 0 11 4 Every 2 months or more often in hard water areas the manual drain valve should be opened fully flushing out accumulated materials salts and other particles which are natural by products of boiling water The optional AutoFlush System feature automatically drains the Mr Steam generator following each use A time delay allows the water to cool down about two hours before it drains by gravity for a safe and gentle operation Typical locations include closet vanity cabinet heated attic or basement NOTE The standard length of the cable for connecting the c
55. omaSteam Operation and Instruction Manual PN 100402 for installation information before the steam line is installed at the technical downloads section of www mrsteam com mr steam INSTALLING THE ROUND OR SQUARE AROMASTEAM STEAMHEAD 2 NPT NOTE A 17 clearance hole around the steam pipe is needed to mount the steamhead STEP 1 Locate steam head 6 12 inches above floor except for 1 Tub shower enclosures install 6 inches above tub top edge 2 For enclosures with acrylic or other non heat resistant flooring install Acrylic Shield Part Number MS 103938 STEP 2 Install steamhead with the oil well facing up as shown Hand tightening is sufficient when teflon or equal pipe thread sealing compound is used STEP 3 Secure a bronze drop ear fitting to a header and run a Jo copper steam line from the steam generator to the drop ear fitting Install a temporary nipple 6 or longer in the drop ear fitting to locate the steamhead after the wall is finished STEP 4 After the wall has been finished mark on the nipple where the surface of the wall is Remove the nipple and measure the portion that was in the wall the end to your mark Subtract from that dimension and select a brass nipple of that length to finish the installation STEP 5 Wrap teflon tape around the threads of the new nipple and screw the nipple into the steamhead Do not use wrenches or tools which would damage the steamhead s finish Wrap teflon tape ar
56. ontrol to the steam generator is 30 feet The steam generator and control must be located accordingly A 60 foot cable is available as a special order part for eTempo and iTempo PN 103990 60 for iTempo and PN 104117 60 for iSteam IMPORTANT NOTE The control cable should be run in a dedicated 1 conduit to facilitate installation and service DO NOT route iSteam iTempo Plus iTempo HomeWizard or iGenie control wiring inside conduit together with power lines or close to hot water or steam piping Doing so may Items 1 4 DO NOT install steambath generator inside steam room a shock hazard will occur DO NOT install steambath generator outdoors or wherever environmental conditions may result in a shock hazard or affect performance of the generator To prevent damage to the steam generator or a fire hazard DO NOT install steambath generator near flam mable or corrosive materials or chemicals such as gaso line paint thinners or the like Installation in areas hav ing high concentrations of chlorine such as pool equipment room must be avoided Burn Hazard Steam line safety valve drain valve and plumbing become hot during operation and remain hot after shutdown for a period of time Provide appro priate protection including insulating plumbing lines Avoid plumbing runs and steamhead locations that can come in contact with bathers Items 5 7 5 DO NOT install steambath generator or plumbing lines in unheated atti
57. or illustrative purposes only Inf steam Installation Operation amp Maintenance Manual GENERATOR DIAGRAM Water Inlet Control amp Accessory Connections La e el for servicing 4 LL EE EEN IMPORTANT NOTES Provide a minimum of 12 inches at both ends and top of the steam generator or as required for servicing Alternately provide unions as required to facilitate installation and dis connection of the steam generator The minimum clearance from combustible surfaces is zero all around __ Side View Showing 7 Element Access Panel NOTES 1 M Optional AutoFlush TO AVOID EQUIPMENT 2 All units in inches MM DAMAGE DO NOT 3 MS Super 4E includes 2 MS Super 1E units CONNECT POWER 4 MS Super 5E includes 2 MS Super 2E units SUPPLY DIRECTLY TO 5 MS Super 6E includes 2 MS Super 3E units ELEMENTS WATER INLET A STEAM OUTLET fe SAFETY VALVE MANUAL DRAIN VALVE 4 AUTOFLUSH VALVE yy All drawings are for illustrative purposes only mr steam Installation Operation amp Maintenance Manual ELECTRICAL CHART ELECTRICAL Vol Max Room Wire Size Wire Size Model No Cu Ft KW Volts Phase Amps Wafer 40 C AWG for 45 C Ambient Ambient NSOE All electrical wiring to be installed by 208 21 10 5 a qualified licensed electrician in accordance with MS 90E 100 5 0 3 14 12 12 National Electrical Code and local el
58. or the safe and efficient installation and operation of this generator These are types of potential hazards that may occur during installation and operation ATSTITA Indicates a potentially hazardous situation which if not avoid ed could result in death or serious injury NANI Indicates a potentially hazardous situation which if not avoid ed may result in minor or moderate injury or product damage IMPORTANT NOTE This highlights information that is especially relevant to a problem free installation All information in these instructions is based on the latest product information available at the time of publication Sussman Automatic Corporation reserves the right to make changes at any time without notice HYPERTHERMIA occurs when the inter nal temperature of the body reaches a level several degrees above the normal body temperature of 98 6 F The symp toms of hyperthermia include an increase in the internal temperature of the body dizziness lethargy drowsiness and faint ing The effects of hyperthermia include a Failure to perceive heat b Failure to recognize the need to exit the steambath c Unawareness of impending risk d e and Fetal damage in pregnant women Physical inability to exit the steambath f Unconsciousness NESNE The use of alcohol drugs or medication can greatly increase the risk of hyperthermia When using this steam bath equipment basic safety precau
59. ound the threads of the nipple and screw the nipple and steamhead assembly you just made into the drop ear fitting in the wall The steamhead should be flush with the wall and the well must be facing up IMPORTANT NOTE DO NOT disassemble steamhead Mr Steam s steamhead is shipped fully assembled and requires no additional assembly To preserve steam head finish DO NOT use wrench or other tools to tighten DO NOT use abrasive cleansers or chemicals Use only water with mild soap and a non abrasive sponge Because the steam head and direct steam emissions are very hot locate the steam head where incidental contact by bather with the steam head or direct steam emis sion cannot occur Consult with supplier of acrylic fiberglass and other non heat resistant enclosures for recommended steamhead location Use Acrylic Shield PN MS 103938 round or PN MS 103938SQ square See instructions provided with steam shield Apply with silicone or equal Installation Operation amp Maintenance Manual 1 8 minimum clearance required when Acrylic Shield is used See installation instructions provided E with the Acrylic Shield Use Teflon or equal sealant on pipe threads sealant as required for moisture seal istur End of pipe to be recessed ER 1 4 without Acrylic Shield Oil Well 1 8 with Acrylic Shield Steamhead shown with optional acrylic shield Locating Nipple All drawings are f
60. pproximately 5 minutes unless equipped with factory installed Express Steam option at the steam head Steam will shut off when desired temperature is reached and will automatically resume when room temperature drops below set point GO Steam will shut off automatically when control counts down to zero To shut steam off manually turn control OFF To clear steam from enclosure area turn shower on before opening door p If unit does not start and control does not turn ON control display does not light up then turn breaker off for 20 seconds and try again C1 Check all internal and external plumbing fittings for leaks while the steam is on OPTIONAL amp ACCESSORY EQUIPMENT Refer to specific instruction manual for installation operation and maintenance of optional equipment and accessories such as iSteam iTempo Plus iTempo Home Wizard iGenie and MSTS TROUBLESHOOTING All electrical troubleshooting to be performed by a qualified licensed electrician Step 1 Check main incoming power to the unit Step 2 Verify the transformer is receiving 208 240 VAC Step 3 Verify that you have 24VAC coming out of the transformer WHT amp WHT BLU wires into the board Step 4 Verify that you have the green light on the PC board Contactor Water Feed Solenoid Step 5 Push the white test button to Water Fee run the generator for 10 minute test cycle Make sure the steam room i
61. r seating area The control features an integral temperature sensor Locate the control in a location representative of the desired steam bathing temperatures Do not locate the control above or near the steam head or direct steam emissions Locate the control on a vertical wall e The control and AudioWizard cables are 30 feet Insure that the control steam generator and optional AudioWizard are located accordingly IMPORTANT NOTES e If required contact Mr Steam to purchase an optional 60 iSteam 2 0 control cable part number 104117 60 e A 60 foot cable is NOT available for AudioWizard e f the control is installed outside the steam room a Remote Temperature Probe Part Number iMSTS must be installed inside the steam room Refer to the iMSTS installation manual before installing the control e Insure Mr Steam steam generator is iSteam 2 0 compatible and has a serial number 930030 or higher Installation with Optional Rough In Box A rough in box is supplied with iSteam 2 0 for new construction The rough in box will allow precise location of the iSteam 2 0 control and provide a secure and easily identifiable place for the cables while the steam room is being constructed STEP 1 Take the rough in box out of the package Remove the two screws 1a and place them in the top and bottom wings of the rough in box 1b STEP 2 Select a KNOCK OUT 2a to route the control cable into the box Use a second KNOCK OUT if the optiona
62. rs IMPORTANT NOTE Do not apply excessive amounts of silicone Do not apply silicone to any other parts of the control including the adhesive gasket Insure the mounting surface is clean and dry as required for good adhesion Hold the control with the arrow on Before use remove the screen protector facing up and press the control ano cene INE poss off screen protector against the wall until the adhesive sticks and holds firmly Control may have to be supported or secured until the silicone has cured for 24 hours This End Up mr steam Controls Operating Instructions Set the steam bathing duration and tem perature according to personal preference however it is highly recommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels mr steam Set the duration at 10 minutes max to gauge comfort and safety levels This will allow the steam generator to heat up and begin producing steam 8 19 AM Monday Stand By Screen Touch anywhere on the display to wake up the iSteam 2 0 Control Start Screen n Press the START button to turn the steam gen erator ON and to display the Dashboard screen Steam will begin to flow a few minutes after the fonds START button is pressed The time required for the steam room to reach steam bathing tempera system Settings tures depends on the steam room construction P6 11 and steam generator specifications Accessories p ACCESSORIES
63. s AUD y s and Play empty Knock Out g Connectic Field Wiring Liquid Step 6 Verify that you have 24 VAC Level Probe to the water feed solenoid GRY amp R IK K 7 Ste WHT GRY wires will fill when needed ie E Step 7 Temporarily short out the WLS Purple wire and i d A Ov s GND Green wire terminals and verify the contactor engages Step 8 When the red light is on verify 24 VAC RED amp WHT RED wires to the contactor Step 9 Check main voltage on the load side of the contactor when it is engaged Step 10 If all steps on the power path were verified turn off power to the unit and pull the heating element via the left hand access panel for inspection DO NOT disassemble internal components internal components contain no serviceable parts All drawings are for illustrative purposes only mr steam Installation Operation amp Maintenance Manual SYSTEM STATUS CODES The control either iSteam iTempo or iTempo Plus may display a status code if the steam generator is not functioning properly Code Code Meaning Probable Cause Suggested Remedy H20 Water level is not satisfied within 5 min Prri Temperature Probe Error or Prr2 Er Incorrect Field Supply Voltage green light on liquid level control board will be off Err2 Button on control is pressed for more than 5 minutes Errb Water level not satisfied in a tandem set up Check secondary generators see H20 Err Liguid Le
64. s lower than the AutoFlush assembly PEL ae DO NOT REMOVE A npn e vd must be available The AutoFlush System valve outlet is 2 NPT y THIS DRAIN VALVE Arrow indicates correct direction of flow Check plumbing code for receptor trap and vent requirements NO Use copper or brass nipple 2 NPT x 3 2 or longer not supplied to connect AutoFlush valve end B to the Drain Valve valve end A and B are indicated on bottom of AutoFlush Valve NANN DO NOT REMOVE THE DRAIN VALVE Removal may cause equipment and property damage If there is not enough room for the valve an elbow and a short nipple not provided can be added 3 Open Drain Valve handle must be aligned with brass nipple 4 Connect the AutoFlush System cord connector to the three pin connector as shown NYLSUNBNS DO NOT drain into a steam enclosure or any location where accidental contact with drain water may occur In the event of a power failure the AutoFlush System valve will open and may dis charge boiling water causing a scalding hazard Steam Generator Drain Valve Nipple e b When using sweat fittings use only tin base solder with a melting THE DRAIN VALVE ide point below 600 degrees F DO NOT overheat Ends of water supply shown in the correct open tubing must be thoroughly clean for a minimum distance of 1 from pone ends DO NOT remove valve cover AutoFlush Shown Fully Assembled TO CHECK OPERATION 1 Turn on Mr Steam
65. s save When AutoStart is armed you will see a in the upper right corner of the screen When AutoStart starts your steambath it will allow the steambath 12 05 am to run for only 10 minutes To continue steam bathing press the continue button If the continue button is pressed AutoStart will remain active for the next scheduled start time To stop the steam bath press the stop button If the ON button is pressed within 10 minutes the steambath will turn off If the STOP button or 10 minute time out turns the steam generator off AutoStart will automatically be deactivated mr steam iSteam 2 0 App The iSteam 2 0 App can be downloaded trom the App Store or Google Play BEFORE REMOTELY ACTIVATING THE STEAMBATH CONFIRM THAT IT IS UNOCCUPIED Activating the steam in an occupied room may subject persons to the hazards listed in this manual NENG ONLY ACTIVATE THE STEAMBATH IF THE STEAM ROOM DOOR IS CLOSED Activating or using the steambath with an open door may cause prop erty damage or injury to persons outside of the steam bath IMPORTANT NOTE The iSteam 2 0 and App will update each other based on changes inputted There may be a lag of a few seconds between making a change on one device and it updating on the other Configuring the iSteam 2 0 Set the passcode and turn on the Wi Fi from the iSteam 2 0 see page 11 The default passcode is 0000 Configure iSteam Wireless Search for iSteam units Dema Made iStea
66. side the steam room per installation instructions supplied with the Remote Temperature Probe Failure to install ac cording to instructions will result in an inoperative control and overheating of the steam room Warranty e To view or download the Mr Steam Control Warranty and register your product go to blog mrsteam com wr l Controls mr steam Feel Good Inc www mrsteam com Products information and specifications are subject to change without notice For more information call Sales amp Support at 1 800 76 STEAM East Coast or 1 800 72 STEAM West Coast for more information Im r Steame sussman Automatic Corporation hello mrsteam com www mrsteam com 43 20 34th Street Long Island City NY 11101 9410 S La Cienega Blvd Inglewood CA 90301 1800767 8326 Fax 718 472 3256 180072 STEAM Fax 310 216 2944 2014 Sussman Automatic Corporation Mr Steam and des AromaFlo AutoFlush AutoSteam Butler Package ChromaSteam Clean Steam Every Time Club Therapy Digital 1 Express Steam From Bathroom to Spa iGenie iSizing iSteam 2 0 iSteam 2 0 Plus Making Wellness a Way of Life MusicTherapy Spa Package Steam Genie Steam on Demand Steam Home SteamTherapy Sussman Valet Package Virtual Spa System Voice Genie and Voice Wizard are registered trademarks of Sussman Automatic Corporation AudioWizard A Lifetime of Pleasure HomeWizard iButler iSteam 2 0TV iTempo iTempo Plus MySteam Smart
67. tions should always be followed including the following IMPORTANT SAFETY INSTRUCTIONS 1 READ AND FOLLOW ALL INSTRUCTIONS 2 DO NOT permit children under D Excessive temperatures have a high the age of 16 to use this steambath 3 AWZGQIN Steam is hot and can cause injury or death if improperly used Steam rooms contain steam and elevated tempera tures Please read and observe all warnings in this manual before installing or using a steam room 4 To reduce the risk of injury A The wet surfaces of steam enclosures may be slippery Use care when entering or leaving B The steam head is hot DO NOT touch the steam head and avoid the steam near the steam head C Prolonged use of the steam system can raise excessively the internal human body tempera ture and impair the body s ability to regulate its internal temperature hyperthermia Limit your use of steam to 10 15 minutes until you are certain of your body s reaction The peel and stick warning label located in potential for causing fetal damage during the early months of pregnancy Pregnancy or possibly pregnant women should consult a physician regarding correct exposure E Obese persons and persons with a his tory of heart disease low or high blood pressure circulatory system problems or diabetes should consult a physician before using a steambath F Persons using medication should con sult a physician before using a steam bath since some
68. to turning on the steambath DO NOT place drops in a hot steam head as serous injury can result if you do not follow this warning 3 Start with one drop to gauge strength and suitability Limit to a maximum of a few drops for a steambathing session 4 The bather should exit the steambath IMMEDIATELY if dizziness occurs If skin irritation occurs stop using the oils immediately Remove any excess oil by washing in mild soap and water If ingested rinse mouth with water Administer water or milk to dilute Contact a physician immediately Aromatic oils should be added to steamhead before turning on the steambath unit DO NOT add oil dur ing steambathing or when the steam head is heated Tightly close bottles when storing oils Keep bottles away from sources of ignition All drawings are for illustrative purposes only WARRANTY To view or download the Mr Steam Residential Generator Warranty and register your Product go to blog mrsteam com wr Installation Operation amp Maintenance Manual AromaSteam 10ml bottle with integrated dropper 77 Recess for essential oil AromaSteam steamhead install per instructions on pg Steam emission slot 21 mr steam Feel Good Inc www mrsteam com Products information and specifications are subject to change without notice Please call Sales amp Support at 1 800 76 STEAM East Coast or 1 800 72 STEAM West Coast for more information
69. tructions 2 e iSteam 2 09 Control Installation Template sie RE 2 Control Cable 30 ft BO Content os EE 3 Steamhead Dimensional Information 3 Tube of Silicone Sealant Before net Ge ER BERE RE 4 ee Locating CCC ONO ae see 5 no Box Installation with Rough In Box 5 6 Optional Surface Installation without Rough In Box 6 Mount Gasket iISteam 2 0 AS el eel AE 7 8 Operating Instructions Stand By Start Dashboard Set Timer 9 Set Temperature User Preferences 10 Accessories AudioWizard AromaSteam Bea RE N Seen eT eer eee 10 Optional Accessories esses 11 Settings gt Set Day Time gt Display 11 Setting PAN OU le NE TTE 11 Settings gt Passcode s 12 AO E see ees E N 12 Steam 2 0 FOR E ema 13 14 Care Tips Safety amp Operating Info 15 llis ICY RE 15 Dimensional Information MUT 4 bh gt Control ID Tag Pigtail 8 474 Audio Pigtail Blue Cap 7 4 TAA Wall location for optional surface mount Wall location for flush mount mr steam Before Installing INWZSININ To avoid unintentional steambath Op eration do not locate the control where other controls accessories shower heads valves body sprays or simi lar within the shower could cause confusion or interfere with
70. vel Control Board malfunction Water Supply is off Defective water feed solenoid Turn on Water Supply Check replace water solenoid valve Water feed probe not functioning Drain Valve Open AutoFlush not functioning Control cable MSTS cable cut Check clean probe Check probe wiring Check Close drain valve Check Replace AutoFlush Replace control cable MSTS Internal problem with control MSTS Incorrect voltage supplied to Generator Control cover misalignment Replace control MSTS Supply steam generator with the correct voltage noted on the data plate label Remove and reinstall control cover Remove control cover and clean cover Debris behind control cover Memory error in LLCB control and keypad with a damp cloth Press ON OFF to clear Replace control if code remains LIQUID LEVEL CONTROL BOARD Explanation of LED Indicators GREEN LED is ON when there is 208 240 Volt incoming power connected 24 Volt transformer secondary output and on board 5 Volt DC control power are present YELLOW Water level indicator LED is OFF when no water is detected for more that 5 seconds ON when water level is satisfactory For units with AutoFlush if more than five hours have elapsed since last usage and this LED is ON it is indicative of an AutoFlush or water level probe circuit malfunction RED Contactor relay indicator LED is ON when relay is closed and sending 24 Volts to the contactor coil This LED comes O

Mr. Steam S3C1IAFWH Installation Guide

Contents

Download Pdf Manuals

Related Search

Related Contents