Home

Mr. Steam MSITPLUSSQ-ORB Installation Guide

1. Installed Remote Temperature Probe showing a minimum of 1 4 of the probe exposed to steam room air mr steam iTempo Operating Instructions The iTempo Control features programmable digital temperature control a fixed 60 minute duration ON OFF and PAUSE The control can be set at a temperature range from 80 F up to 120 F NGG Set the steambathing temperature according to personal preference however it is highly recommended to begin steambathing at a low temperature setting for a very short duration to gauge comfort and safety levels ON OFF Diagram 1 Press the ON OFF key to start or stop the flow of steam Steam will begin to flow a few minutes after the control is turned ON The duration required for the steam room to reach steambathing tempera tures depends on the steam room construction and steam generator specifications Steam may continue to flow for a short time after the control is turned OFF PAUSE FEATURE Diagram 2 If a pause in steam flow is desired press the PAUSE key The display will flash while the control is in the PAUSE mode The timer will continue to countdown while in the PAUSE mode Steam may continue to flow for a short time after pause is pressed Installation amp Operating Instructions mr steam DIAGRAM 1 mr steam DIAGRAM 2 Drawings for Illustrative Purposes Only mr steam Installation amp Operating Instructions HOF N li TIMER FEATURE
2. When the control is turned ON a 60 minute time du ration is initiated The control will turn off after 60 minutes unless the control is turned off manually MEMORY FEATURE If the control is turned off manually before 60 minutes then the default temperature of 110 F will be used the next time the control is turned on If the control times out at 60 minutes not manually turned off then the previous user temperature setting will be used when the steambath is used again DIAGRAM 3 SETTING THE TEMPERATURE Diagram 3 The control is pre set and will display the temperature setting of 110 F default setting Use the UP and DOWN keys to change the temperature setting from 80 F to 120 F in one degree increments CHANGING THE TEMPERATURE UNITS F C Diagram 4 When the generator is Off Press and hold ON OFF key for 10 seconds The temperature units will be dis played as Fahrenheit TuF or Celsius TuC Use the UP DOWN keys to choose between TuF and TuC Press ON OFF key to accept the new units and exit DIAGRAM 4 Drawings for Illustrative Purposes Only 12 mr steam Installation amp Operating Instructions iTempo Plus Operating Instructions m am The iTempo Plus Control features programmable tempera ie g ture control programmable time duration clock Aroma Steam ChromaSteam ON OFF and two personal settings NOSAINE Set the steambathing temperature according to personal preference however
3. 00000 or any other brand of steam generator are not to be operated with iTempo controls Doing so may result in an inoperative installation This document contains important safety operation and maintenance information Leave this document with the homeowner Do not discard this document e Discontinue use of the steam generator or control if the steam generator is damaged or otherwise not functioning properly Doing so may result in an inoperative or hazardous installation All illustrations are for illustrative purposes only mr steam Installation amp Operating Instructions Dimensional Information f for the Round and Square l iTempo and iTempo Plus BOX CONTENTS e iTempo or iTempo Plus Control e Control Cable 30 ft Steam head e Tube of Silicone Sealant ete eet S t CA e Owner s Manual Drawings for Illustrative Purposes Only mr steam Installation amp Operating Instructions Installation Instructions for Round amp Square iTempo and iTempo Plus STEP 1 Determine the desired installation location of the control The iTempo and iTempo Plus controls are designed to be installed inside or outside the steam room as a matter of personal preference If the control is installed outside the steam room a Remote Temp erature Probe part number MSTS must be installe
4. INSTALLING cont Install the iTempo or iTempo Plus controls ac cording to installation instructions Failure to install according to instructions will result in an inoperative control or hazardous overheat ing or inadequate heating of the steam room If an Tempo or iTempo Plus control is installed outside the steam room a Remote Temperature Probe PN MSTS must be in stalled inside the steam room per instructions for the Remote Temperature Probe Failure to install according to instructions will result in an inoperative control and overheating of the steam room Do not route iTempo Plus iTempo Home Wizard or iGenie control wiring inside conduit together with power lines or close to hot water or steam piping Doing so may result in an inoperative or haz ardous installation Do not alter or modify any Mr Steam products including the steam generator iTempo Plus iTempo iGenie or Home Wizard controls Doing so may result in an inoperative or hazardous installation and will void the warranty Installation amp Operating Instructions IMPORTANT NOTES e Turn power to the steam generator OFF be fore connecting the control to the generator Failure to turn the power off will result in an inoperable control e Do not operate iTempo Plus Tempo Home Wizard or iGenie controls with anything other than a Mr Steam iTempo compatible steam generator Mr Steam residential steam genera tors with serial numbers lower than 9
5. LS AN Installation Operation amp Maintenance Manual iITEMPO amp iTEMPO PLUS CONTROLS mr steam Feel Good Inc www mrsteam com Table of Contents General Information ccsccsssecsesesseesesstesseesses 1 Before Installing s s s 1 2 Dimensional Information c scccsccseseeeseesses 3 lnstallations isns eaten a 4 7 Installing the Remote Temperature Probe ou 8 10 Tempo Operating Instruction 11 12 iTempo Plus Operating Instruction 13 16 Care and Maintenance 17 Warranter e a a a 17 General Information As you follow these instructions you will notice warning and caution symbols This blocked information is important for the safe and efficient installation and operation of this control These are types of potential hazards that may occur during installation and operation ANSOAIN states a hazard may cause serious injury or death if precautions are not followed XSAN signals a situation where minor injury or product damage may occur if you do not follow instructions IMPORTANT NOTE This highlights information that is especially relevant to a problem free installation mr St amMs Sussman Automatic Corporation hello mrsteam com www mrsteam com 43 20 34th Street Long Island City NY 11101 1 800 76 STEAM Fax 718 472 3256 9410 S La Cienega Blvd Inglewood CA 90301 1 800 72 STEAM Fax 310 216 2944 mr steam BEFORE INSTALLING Carefully insp
6. STEAM West Coast 2013 Sussman Automatic Corporation Mr Steam and des AromaFlo AutoFlush Au toSteam Butler Package ChromaSteam Clean Steam Every Time Club Therapy Digital 1 Express Steam From Bathroom to Spa iSizing iSteam iSteam Plus MusicTherapy Spa Pack age Steam Genie Steam on Demand Steam Home iTempo iTempo Plus Steam Therapy Sussman Valet Package Virtual Spa System Voice Genie and Voice Wizard are reg istered trademarks of Sussman Automatic Cor poration AudioWizard Home Wizard iButler iGenie iTempo iTempo Plus MySteam Smart Sizing SteamStart SteamStop The Intelligent Steambath are trademarks of Sussman AutomaticCorporation 100474 rev 2 13
7. arp blade Sealant skins in 5 minutes dries to touch in 1 hour Fully cures and bonds in 24 hrs Drawings for Illustrative Purposes Only mr steam Installation amp Operating Instructions IMPORTANT NOTE Do not apply excessive amounts of silicone Do not apply silicone to any other parts of the control including the adhesive gasket STEP 7 Diagram 6 Insure the mounting surface is clean and dry as required for good adhesion Hold the control with the LED display in the 12 o clock position and press the control against the wall until the adhesive sticks and holds firmly Control may have to be supported or secured until the silicone fully cures and bonds DIAGRAM 6 Drawings for Illustrative Purposes Only mr steam Installing the Remote Temperature Probe PN MSTS The Remote Temperature Probe is required when the iTempo or Tempo Plus Controls are installed outside the steam room The Remote Temperature Probe P N MSTS is for use with iTempo and iTempo Plus Controls only Do not use with any other controls Do not use any other temperature probe with the iTempo and iTempo Plus controls Noncompatible products may result in an inoperative con trol and a hazardous condition NeMbuife S Install the iTempo or iTempo Plus controls according to the in stallation instructions on pages 3 5 Failure to do so may result in an inoperative con trol and a hazardous condition 1 Determine the loca
8. d inside the steam room If the control is installed inside the steam room the control must be located e 4 5 feet above the floor near the bather seating area e The control features an integral temperature sensor Locate the control in a location repre presentative of the desired steambathing temperatures Do not locate the control above or near the steam head or direct steam emissions Locating the controls near the steamhead or near direct steam emissions may result in poor steam room temperature control DIAGRAM 1 e On a vertical wall IMPORTANT NOTE The control cable length is 30 feet Insure that the control See installation instructions for and or steam generator are located accordingly the MSTS Temperature Probe Contact a Mr Steam technical service representative if a before rough in or installation longer cable is required 60 ft cable PN 103990 60 of control pg 8 9 Drawings for Illustrative Purposes Only mr steanrY STEP 2 Diagram 1 Make a 2 98 wide by 3 7 8 high cutout in the desired control location Do not oversize or undersize the cutout STEP 3 Diagram 2 Route the control cable provided with the control from the wall cutout to the steam generator Connect one end of the cable to the steam generator connector NOTE The connector is keyed with the flat facing up The control cable is the same at both ends IMPORTANT NOTE Be careful not to strain staple pinch or otherwise damage t
9. d temperature settings will be used when the steambath is turned on PROG 1 AND PROG 2 Diagram 8 Use the P1 P2 key program to store preferred settings To program preferred settings Press ON OFF key to turn generator on Press P1 P2 key once to program PROG Press it twice to program PROGZ The selected parameter will be displayed Enter the preferred time and temperature settings The iTempo Plus will store the following settings set point time duration amp aroma state To select PROG1 or PROG2 Press ON OFF key then press P1 P2 key once to select PROG1 press it twice to select PROG2 The steambath will begin to operate at the stored settings jE DIAGRAM 8 mr steam CHANGING THE TEMPERATURE UNITS F C When the generator is Off Press and hold ON OFF key for 10 seconds The temperature units will be displayed as Fahrenheit TuF or Celsius TuC Use the UP DOWN keys to choose between TuF and TuC Press ON OFF key to accept the new value and exit AROMASTEAM Diagram 9 The AromaSteam is an optional accessory that automatically injects aromatic oil into the steam Press the ON OFF key to turn the steam generator on Then press the AROMA key The Aroma indicator will be displayed The AromaSteam turns off auto matically when the steam generator stops heating Press the AROMA key to turn it off during a steam session The indicator will turn off CHROMASTEAM Diagram 10 The C
10. ect the control and packaging for shipping damage In the event of ship ping damage please contact the carrier for claim information Our customer service de partment can assist you with any missing or damaged parts AXAN To avoid unintentional steam bath operation do not locate the control where other controls accessories shower heads valves body sprays or similar within the shower could cause confusion or inter fere with the Mr Steam control s intended use and function Do not use any iTempo Plus iTempo Home Wizard or iGenie controls without reading and understanding the respective Installation and Operation Manual and Mr Steam steam generator Installation and Operation Manual PN 101289 Revision number 10 0 08 or higher Failure to read and understand these instructions may result in an inopera tive or hazardous installation Installation amp Operating Instructions A peel and stick warning ticker is provided in the MrSteam steam generator Installation Operation and Main tenance Manual This manual is provided ith every steam generator The warning ticker must be read and permanently affixed n a conspicuous location near the steam oom Failure to read and affix this warning sticker in a conspicuous location may result in serious injury or death Please call MrSteam at 800 767 8326 for a free replace ment or if you have any questions regarding the warning sticker v a g ns mr steam BEFORE
11. he control cable Route cable as required to permit replacement Do not route cable inside conduit together with power lines or close to hot water or steam piping STEP 4 Diagram 3 Firmly connect the other end of the cable to the control Turn on power to the steam generator and test the control to verify correct connections Test per the instructions on pages 10 15 With verification of proper control function proceed to Step 5 uo Installation amp Operating Instructions DIAGRAM 2 DIAGRAM 3 Drawings for Illustrative Purposes Only mr steam Installation amp Operating Instructions A DIAGRAM 4 If the generator is on for more than a few minutes steam will start coming out of the steamhead Insure that steamroom is not occupied STEP 5 Diagram 4 Remove and discard peel off paper to expose adhesive liner STEP 6 Diagram 5 Run a bead of silicone provided as shown to the outer edge of the control faceplate following the contour of the circle or square shape Use silicone as required to create a moisture seal NOTE The silicone supplied by Mr Steam can DIAGRAM S be used to meet a variety of sealing and gasketing It cures to silicone rubber and adheres to glass wood metal porcelain ceramic tile painted surfaces many plastics and rubber Surfaces must be clean and dry Apply thin layer of product Fit together and support if necessary Allow excess material to cure then trim with a sh
12. hromaSteam is an optional accessory that provides colored light in the steam room Press the CHROMA key to turn light on Press twice to select the next color Press again to turn the light off Note that the light can be turned ON even if the steam genera tor is OFF Installation amp Operating Instructions bug aroma mr steam DIAGRAM 9 chroma mr steam DIAGRAM 10 mr steanr Installation amp Operating Instructions Display mr steam Up Key i Time Display Time Display Adjust Key V Adjust Key h Down Key ag aa AromaSteam ChromaSteam Key Key Care Tips for all Controls and Steamheads 1 Use only mild soap and water on a soft cloth to clean the control and steamhead 2 Do not use abrasive cleansers 3 If the decorative cover is damaged on the iTempo or iTempo Plus call Mr Steam technical service for replacement parts NOTE Replacement of the decorative covers requires removal and reinstallation of the control from the mounting surfaces Warranty To register your steam generator unit online and m m to review the Mr Steam Limited Lifetime Warranty please go to pa blog mrsteam com wr g 17 TEMPLATE FOR CONTROL INSTALLATIO N SEE PG 4 A fo N mr steam Feel Good Inc Products information and specifications are subject to change without notice For more information call Sales amp Support at 1 800 76 STEAM East Coast 1 800 72
13. isplay the steambath dura tion time on the clock The control is pre set and will display a TIME setting of 20 minutes default set ting With the TIME or CLOCK displayed press the UP or DOWN keys Diagram 5 to set the desired duration time 2 60 minutes in two minute incre ments Set the steambath duration according to personal 22 preference however it is highly recommended to DIAGRAM 5 begin steambathing at a very short duration to gauge comfort and safety levels The control will am turn off when the duration period times out Then z the clock time will be displayed A hs mr steam Installation amp Operating Instructions SETTING THE TEMPERATURE Diagram 6 Press TEMP key to set the desired temperature or dis play the temperature setting Diagram 7 The control is preset and will display a temperature setting of 110 F default setting With the temperature displayed press the UP or DOWN keys to set the desired temperature 80 F to 120 F in one degree increments Set the steambathing temperature according to personal prefer ence however it is highly recommended to begin steambathing at a low temperature setting to gauge comfort and safety levels MEMORY FEATURE If the control is turned off manually before it times out then the default settings of 20 minutes and 110 F will be used the next time the control is turned on If the control times out not manually turned off then the previous user time an
14. it is highly recommended to begin steambathing at a low temperature setting for a very short duration to gauge comfort and safety levels POWERING UP THE UNIT Diagram 1 OSS When the generator is first powered up or after a power interruption the clock display flashes and the clock is DIAGRAM 1 ready to be set up NOTE Pressing the ON OFF will start the generator even if the clock has not been set ON OFF Diagram 2 Press the ON OFF key to start or stop the flow of steam The Temperature Set Point is displayed Steam will begin to flow a few minutes after the control is turned ON The duration required for the steam room to reach steambathing temperatures depends on the steam room construction and steam generator specifications Steam may continue to flow for a short time after the control is turned OFF mr steam mr steam CN Jaona anona gR i DIAGRAM 2 Drawings for Illustrative Purposes Only mr steam Installation amp Operating Instructions iTempo Plus Operating Instructions cont SETTING THE CLOCK Diagram 3 When the display is not flashing Press and hold the DIAGRAM 3 TIME key until the display starts flashing Use the UP DOWN keys to select the desired time at this time the AM PM logo will be displayed Press the TIME key to save changes NOTE The clock can only be set when the generator is off SETTING THE STEAMBATH DURATION Diagram 4 DIAGRAM 4 Press TIME key to set or d
15. re _ Probe Connection Teinperature Probe Cable 30 feet Mr Steam Steam Generator shown with cover removed and NOT installed 1 DIAGRAM Drawings for Illustrative Purposes Only mr steam 5 Route the end of the probe cable with the tem perature probe through the wall into the steam room as shown in Diagram 2 IMPORTANT NOTE Do not strain staple pinch or otherwise damage the probe cable 6 With a minimal length of the cable exposed apply silicone provided to the hole in the wall as required to create a moisture seal as shown in Diagram 2 7 Push the temperature cable and probe into hole as required to leave minimum 1 4 maximum 1 2 of the bulb exposed as shown in Diagram 3 Insure a minimum of 1 4 of the temperature probe is exposed to the air Failure to do so may interfere with the ability to sense temperature and may result in excessive steam room temperatures The exposed area of the tempera ture probe must be free of silicone or any materials or obstructions that prevent direct exposure to the steam room air Failure to do so may interfere with the ability to sense temperature and may result in excessive steam room temperatures NOTE For Illustrative Purposes Only Drawings Not to Scale Installation amp Operating Instructions STEAM ROOM INTERIOR YN DIAG RASS T Im DIAGRAM a Sectional View 1 4 minimum 1 Ya maximum ZZ Silicone Sealant
16. tion of the Remote Temperature Probe Ss The Remote Temperature Probe must be installed a On a vertical surface b 4 5 feet above the floor Installation amp Operating Instructions c in a location representative of the desired steam bathing temperature Locating the MSTS near the steamhead or near direct steam emis sions may result in poor steamroom temperature control d The probe has an integral 30 cable Insure that the probe and or steam generator are located ac cordingly 2 Drill a 5 16 inch diameter hole in the wall Do not oversize or undersize the hole Clean area thoroughly NOTE The silicone supplied by Mr Steam can be used to meet a variety of sealing and gasketing It cures to silicone rubber and adheres to glass wood metal porcelain ceramic tile painted sur faces many plastics and rubber Surfaces must be clean and dry Apply thin layer of product Fit to gether and support if necessary Allow excess mate rial to cure then trim with a sharp blade Sealant skins in 5 minutes dries to touch in 1 hour Fully cures and bonds in 24 hrs 3 Remove the knock out from the steam generator jacket as shown in Diagram 1 4 Insert the probe cable through the knock out and connect to the connector on the steam generator printed circuit board marked EXT TEMP as shown in Diagram 1 8 mr steanrY Installation amp Operating Instructions Temperature Sensor Probe Temperatu

Mr. Steam MSITPLUSSQ-ORB Installation Guide

Contents

Download Pdf Manuals

Related Search

Related Contents