Ariel ZAA212 Installation Guide
Contents
1. panel and 1 side panel together using the M5x30mm 11 64 x 1 bolts and corresponding nuts and washers of SCREW PACK 1 Note which side you place the nut on so that you can easily reach it with a wrench Tighten the panels together just enough for the tip of calking gun can fit in between both panels Caulk along one panel passing over each bolt and screw holes and then tighten the panels together Make sure the bottoms of panels are aligned along a flat surface Press in and wipe away any excess sealant Allowing sealant to cover the screws bolts threads and nuts will help ensure they will not come loose Repeat this step to the remaining panel on the appropriate side Please note that any screw hole that is on an acrylic fiberglass panel can be slightly enlarged modified or completely moved and re drilled in a nearby location so that the panels can fasten more tightly together Seal any hole that is not used or use another type of screw bolt to make use of it 92. 5 4 is equal to inches Example 1016 mm 25 4 40 inches or 0 5 inch x 25 4 12 7 mm e Screw Bolt dimension M stands for metric the first value is the thread diameter and the second is the overall length M Thread diameter x Overall length Example M5 x 25 screw Metric 11 64 x 1 screw or M6 x 50 bolt Metric 1 4 x 2 bolt FEATURES 7 S pew Golem te 1X Ei h Ae G ie 9 6 N J 1 Monsoon Head 2 Loudspeaker 3 Shower Head 4 Glass 5 Diverter 6 Thermostatic faucet 7 Taps 8 Steam outlet 9 Steamer drain 10 Overflow 11 Backwater 12 Light 13 Exhaust Fan 14 Control Panel 15 Towel Rail 16 Jets 17 Handles 18 Air control knob 19 Whirlpool Jets 20 Drain 16 if 18 19 20 INSTALLATION OF CEILING PANEL First drv fit test the ceiling panel onto the shower enclosure to understand how the panels assemble together Note screw hole locations and sealing edges Panels may be adjusted or screw holes enlarged or re drilled so that the panels can fasten tightly together After sealing along the screw holes and adjoining edges use the M4x35mm 1 8 x 1 5 16 self tapping screws and corresponding washers of SCREW PACK 5 to screw down the front of the ceil
3. ARIEL STEAM CABIN INSTALLATION INSTRUCTIONS MODEL ZAA212 Door handles Unscrew the door knob from the door handle remove one vinyl washer but leave the plastic tube and the last vinyl washer place threaded section with plastic tube through one door handle hole of a door reinstall the vinyl washer and then reinstall door knob onto the door handle and glass door If the threads are too short to re screw these items together over the glass remove the fully threaded rod from either the door handle or doorknob whichever side it stuck to and then reinstall it into the door knob with 2 to 3 full turns Inside the bag of door handle hardware there should also be 2 more vinyl washers 2 hard plastic washers and 2 decorative caps Use 1 vinyl washer place it in between the unscrewed end of the door handle and glass door take 1 screw place it through the rounded side of the hard plastic washer and then screw into the door handle through the glass door Place decorative cap over the hard plastic washer to cover the screw Repeat to the remaining door Handheld shower wand and hose Install the hexagonal end of the hose with a rubber gasket onto the wall panel water junction on the left wall panel Install the opposite end of the hose the tapered and rounded end with a rubber gasket onto the handheld shower wand Adjustable shower wand holder Remove screw cover caps from the end mounts of the bar Place s
4. ealant onto the screw and screw holes Screw lower mount into place install bar and then screw upper mount into place replace the screw cover caps Mirror Place a cap anchor then a soft washer onto a screw and then put sealant onto the screw and screw holes and screw mirror onto the rear panel Place decorative cap onto cap anchor covering the screw 16 INTRODUCTION Thank you for choosing AMERISTEAM bathroom products Please read these instructions to help safely and properly assembly use and maintenance this product Keep these instructions for future use This multi functional shower and steam cabin is easy to assemble and use featuring a centralized computer system that will control the aromatherapy steam hydro massage shower jets overhead lighting exhaust fan FM radio and auxiliary CD input It is the first choice for multifunctional steam shower systems for both household and commercial usage The high speed and highly efficient steam generator can save time and energy It can start producing steam within a few short seconds of starting Steam systems can expose your skin to controlled high temperatures that will open skin pours expand capillaries improve blood and lymph circulation virtually eliminate fatigue relax and refresh your body It can also thoroughly help flush dirt grease and bacteria from your skin to help absorb oxygen and moisture for soft elastic and healthy skin Aromatherapy can help relax yo
5. eferably the base Watch out for possible collisions or strong vibrations Do not permanently block in the enclosure for ease of serviceability This steam cabin is designed for indoor use only To prevent any unwanted movement of the steam cabin the enclosure should be installed on a flat level and non slippery surface A sealing agent must be used on all seams of adjoining pieces A caulking gun is highly recommended for this task While wiping away any excess sealant be sure to press in the sealant into the seams they will be sealing If done properly this will help create a positive seal that will ensure a leak free installation Wipe away any excess sealant If any surface has extra silicone residue a soft cloth and soap water mixture or mineral spirits can be used to clean it If the cabinet surface becomes dirty use a wet towel to clean it Daily cleaning of the enclosure is recommended to prevent heavy build ups of deposits Do not use detergents that contain chemical solutions granules or tools with a rough surface to clean the steam cabinet INSTALLING OF OTHER HARDWARE Es Monsoon 15 INSTALLATION OF SLIDING GLASS DOORS AND GASKETS Bef
6. ing to the top door rail of the enclosure Then using the M4 x 30mm 1 8 x 1 1 8 bolts and corresponding washers and nuts bolt the ceiling to the rear panels Fine adjustments of the rear panels can be easily made with moderate pressure Press in and wipe away any excess sealant from around all adjoining seams 13 INSTALLATION OF SPECIFICATIONS FRONT GLASS PANEL ASSEMBLY i SCREW PACK 4 4 K Q Lo c 3 E Z x gt l 5 Zu m n L K UL Nr dil Ib i 1 SI III Ml be 46 5 ll i UP at p L gt por e e al i Ii lt 110VAC 30AMP Lie ii 60HZ 10AWG ee HOT COLD WATER IN j i re il call e nt Ri vili c ls ai 3 ies S pat jA First drv fit test front glass assembly onto the base and rear panel assembly to understand how Lett inne A the panels assemble Note sealing edges and all screw hole locations at adjoining corners and at At O i the bottom rail and base If holes do not line up immediatelv adjust the panels so that thev do La Holes may be enlarged or re drilled so that the panels can fasten tightly together The most rt important edges to be aligned are the bottom and sides After dry fit test has been concluded apply a generous amount of sealant al
7. l Note the rail with one screw hole in the center of the visible portion of the rail is the bottom rail After dry fit test apply a generous amount of sealant into the groves screw holes and along the sides of adjoining edges Press in and wipe away any excess sealant from around all adjoining seams 11 INSTALLATION OF REAR PANEL ASSEMBLY SUPPLIED PARTS SCREW PACK E n 2 aie pi q 9 hee lt A l Q ED q First dry fit test the rear panel assembly onto the base Check panel and screw hole alignment ping L If modifying screw hole s at this location do not modify the hole that the screw is threading ie into tub but only modify the screw hole that the screw thread is passing through panel tia Moving screw holes or adding additional screws not supplied are okay Remember to pilot drill D new screw holes before threading screws into place Using similar techniques as the assembly of the rear panels install seal and bolt the rear panels onto the base using M5x35 11 64 x 1 5 16 bolts and corresponding nuts and washers of SCREW PACK 2 10 7 INSTALLATION OF BASE sic ia drain bodv DRAIN ASSEMBLV OPTIONAL Drain compressi
8. on nut LAI CARICHI MOIO e J r A Flex drain hose J Drain hose gasket Lower drain body Temporarily placing the base into the exact location of usage place a leveling tool along the top ledges of the base to ensure it is level Remove the base and adjust the leveling legs underneath the base to level the top ledges as needed Generally a slight bias toward the drain is better than a slight bias away from the drain Tighten the nuts on the leveling legs to ensure they do not move Make sure all the leveling legs are touching the ground as it may cause the enclosure to bind or rock if they are not OPTIONAL Drain assembly Attach the flexible drain hose and gasket onto the drain assembly Sealant is recommended to be used at this connection Place compression nut onto flex hose then place flex hose gasket onto flex hose and then apply generous amount of sealant onto both sides of the gasket Place the flex hose into lower drain body and tighten the compression nut sealing the flex hose to the drain assembly While wiping away any excess sealant press the sealant into seams they will be sealing If done properly this will help create a positive seal that will ensure a leak free installation 8 ASSEMBLY OF REAR AND SIDE PANELS SCREW PACK o E A i 7 AL Va Li Working on a flat surface align and loosely bolt the center
9. ong all adjoining edges and screw holes Screw the panels together using SCREW PACK 4 AES Ley eee SS 2 WATER SUPPLY SIZE 42 inch Male NPT 3 DRAIN PIPE SIZE 1 inch Note M4x16mm 1 8 x 9 16 self tapping screws and corresponding washers are for the side 4 POWER RATING 3 KW panels and eet n La 1 oA iaia countersunk screw and plastic decorative 5 VOLTAGE RATING 110 120 V screw cover cap are lor the center om rall 6 FREQUENCY 60 HZ Press in and wipe away any excess sealant from around all adjoining seams 12 5 SUPPLIED HARDWARE SCREW PACK 1 M5x30 mm S M5x35 j 9 M4x50 Dimmi 8 SCREW PACK 3 w4x60 Sure 4 SCREW PACK M5x40 chemin 3 4 M4x16 ut 12 M4x30 Som 9 SCREW PACK kl ia N4x35 Arme 3 DRAIN ASSEMBLY PICTURE OPTIONAL ESILI MMI A ASSEMBLY OF FRONT GLASS PANEL SCREW PACK 3 First dry fit test all the panels and rails together to understand how the pieces assemble Assemble both glass panels first onto one rail and then assemble the last rail onto the open end of the glass panels using SCREW PACK 3 Note that each corner of each glass panel will require 1 M4x60mm 1 8 x 1 3 8 self tapping screw from the top and bottom of each rail or 2 M4x50mm 1 8 x 2 self tapping screws from the side of each rai
10. ore installing the doors it is recommended to go over and seal all adjoining seams with sealant from the inside to ensure there are not any broken seals or unsealed corners from working with multiple pieces sealed at different stages during the assembly process For example seal the base to panels panels to panels panels to rails base to rails rails to glass etc Partially disassemble the door rollers from door rail Note in which order the decorative metal nut main metal nut and plastic washer come off the door roller assembly Leave the plastic tube and last plastic washer on the door roller Starting with two center holes for the door handle toward the center of the enclosure partially install the door onto two top door rails Ensure that the plastic tubes are within the glass holes Reinstall the plastic washers and lightly screw in the main metal nuts Repeat this step to lower door rollers and then last door After both doors are loosely installed from the inside of the enclosure close both doors and adjust the door rollers so that the doors align evenly Tighten all the main metal nuts and then reinstall the decorative metal nuts Place on the vinyl door seals F type gaskets onto the outermost edges of the sliding glass doors with the flaps facing the stationary glass panels 14 e Do not use harsh chemicals or rough abrasives or liquids such as ketone acetone or chlorine e Never expose the steam cabin near an
11. organic solution like formic acid or formaldehyde e If there is a scratch found on the acrylic surface polish with 1500 to 2000 grit sandpaper and then apply a polishing compound or toothpaste and rub with a soft clothe e Do not impact the enclosure with a hard object or scratch the surface with a knife e Adjust the water temperature control valve mixer valve slowly to avoid scalding e Be cautious not to touch the steam nozzle when it is in use or just after it has been used as it is very hot and may scald e Keep the steam cabinet ventilated if not being used for long periods of time e Ifthe door does not slide smoothly adjustments of the door rollers may need to be made or lubricants can be placed on the wheels Waterproof grease 1s recommended e Waterproof grease can also be used on any gaskets or movable seals to reduce squeaking protect prolong and improve overall function e Power requirement 110 120 VAC 60 HZ 30 AMP 10 AWG e The electrical and metal components of the steam cabin should be well electrically grounded e Do not try to disassemble the control box or modify the steam cabin without contacting your dealer for professional help e When showering do not use outside electrical appliances inside the shower enclosure for risk of electrical shock e Children should not use this steam cabinet without adult supervision e 25 4 millimeters is equal to 1 inch or the value of mm divided by 2
12. ur body and mind It can help smooth muscle sores and help you sleep more easily It can also help you recover from minor illnesses help regulate your respiratory system and help delay the aging physiology Please consult your physician for more details of how steam aromatherapy can help you The computerized steam system is also equipped with a temperature and timer function that will allow you to set your preferred temperature and duration of usage of the steam system INSTALLATION AND USAGE TIPS Major assembly required While receiving this product check condition and inventory of all accessories hardware and parts Report any damage s to the carrier if applicable and dealer immediately Contact your dealer if you have any questions Please double check that you are using the correct screws of the marked screw packs during the install process If a mistake is made it may result in damage to some parts The waste pipe should be placed about 6 inches from the drain assembly of the enclosure if using the flex hose Although the flex hose can be stretched a long distance in times of servicing the unit the drain assembly and waste pipe should be kept within a reasonable distance to maximize flow efficiency Also the flex hose should always be kept on an even or downward slope never an upward slope When moving the assembled enclosure make sure there is no extra weight on it and push pull from the lowest possible position pr
Download Pdf Manuals
Related Search