Kenroy Home HDP11962 Installation Guide
Contents
1. 7 Determine the length of Chain 16 required to hang the fixture at the desired height using pliers open one end link of chain and attach to the Chain Loop 1 on top of the fixture remove or add chain as desired at this time lace fixture wire and ground wire up through every other link of Chain 16 GLASS SHADE AND BULB INSTALLATION 1 Place a Glass Shade 6 over each Socket 5 and secure with a Socket Ring 7 2 Install a 100 watt max medium base type A bulb not included into each Socket 5 Page 4 ASSEMBLY 1 Chain Loop 2 Pole 3 Upper Arm Assembly 4 Lower Arm 5 Socket x2 B 10 Nipple 6 Glass Shade J 11 Finial TmT Socket Ring x2 100 watt Max type A bulb not included x2 ADDITIONAL PARTS FOR INSTALLATION included INSTALLATION n Om Qa W 13 Wire Nut 14 Cross Bar 15 Ground Screw 16 Nipple 17 Lock Nut x3 Black Wire wz i 18 Outlet Box 19 Canopy 20 Screw Collar 21 Screw Collar 22 Chain Screw x2 Loop Nut round Wire 17 Lock Nut 18 Outlet Box Screw x2 INSTALLATION INSTRUCTIONS 1 Turn off power at main fuse box 19 Canopy 2 Install Cross Bar 14 with Nipple 16 Lock Nut 17 and Screw Collar Loop 20 to Outlet Box 12 using two Outlet Box Screws 18 3 Slide the Screw Collar Nut 21 and then the Canopy 19 onto the end of the Chain 22 then fasten the end link of Chain 22 to the Screw Collar Loop 202. to a failure of the product as a result of an accident misuse abuse negligence alteration or faulty installation or any other failure not relating to faulty material or workmanship This warranty shall not apply to the finish on any portion of the product such as surface and or weathering as this is considered normal wear and tear The manufacturer does not warrant and specially disclaims any warranty whether express or implied of fitness for a particular purpose other than the warranty contained herein The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage including but not limited to any labor expense costs involved in the replacement or repair of said product Page 8 Home Depot x 1962 UPC 053392119621 Aruba Teak Finish Thank you for purchasing this Hampton Bay interior decorative lighting This CAUTION product has been manufactured to the highest standards of safety and quality ar a 1 Before starting installation of this fixture or removal of a previous fixture disconnect the power by turning off the circuit breaker or by removing the fuse as the fuse box QUESTIONS PROBLEMS MISSING PARTS Important Inspect the wire insulation for any cuts abrasions or exposed copper that may have resulted during shipping If there is a defect in the wire Before returning to your local Home Depot please call our Customer Service DO NOT continue
3. Care and Cleaning 1 Use a dry soft cloth to dust or wipe carefully 2 Do not clean with chemicals solvents or harsh abrasives TROUBLESHOOTING Problem Possible Cause Corrective Action The bulb will not light The bulb is burned out 1 Replace light bulb The power is off Faulty wire connection 3 Check wiring 4 Make sure circuit breaker is to the on position The circuit breaker is off The fuse blows or a There is an exposed wire 1 Discontinue use of the circuit breaker trips fixture when the light is 2 Contact a qualified turned on electrician or call the Customer Service Team at 1 877 527 0313 LIMITED WARRANTY The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of one 3 years from date of purchase This warranty applies only to the original consumer purchaser and only to products used in normal use and service If this product is found to be defective the manufacturer s only obligation and your exclusive remedy is the repair or replacement of the product at the manufacturer s discretion provided that the product has not been damaged through misuse abuse accident modifications alterations neglect or mishandling This warranty shall not apply to any product that is found to have been improperly installed set up or used in any way not in accordance with the instructions supplied with the product This warranty shall not apply
4. Screw Collar Nut 22 Chain 4 Insert the fixture wires up through the Nipple 16 5 Install the fixture ground wire under the Ground Screw 15 on the Cross Bar 14 then connect the fixture ground wire to the supply ground wire in the Outlet Box 12 using the Wire Nut 13 Refer to Figure 1 Figure 1 6 Connect the ribbed fixture wire to the white or ribbed supply wire in the Outlet Box 12 using Wire Nut 13 WHITE OR RIBBED WIRE RIBBED WIRE 7 Connect the smooth fixture wire to the black or red supply wire in the FROM HOUSE TROMTIKTURE Outlet Box 12 using Wire Nut 13 NOTE Alway use Wire Nuts 13 to connect wires and push all excess wires and connections back into Outlet Box 12 FROM HOU FROM FIXTURE GROUND W GROUND WIR 8 Raise the Canopy 19 to the ceiling and secure in place by screwing the Screw Collar Nut 21 onto the Screw Collar Loop 20 BLACK OR RED WIRE SMOOTH WIRE FROM HOU FROM FIXTU Page 6
5. the assembly operation Please call our Customer Service Team at 1 877 527 0313 or visit www homedepot com Please reference your Team at 1 877 527 0313 SKU 11962 or UPC 053392119621 when speaking to a Customer Service agent 2 CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS 3 If you have any non electrical questions about this fixture please contact our Customer Service Team at 1 877 527 0313 or visit www homedepot com Please reference your i 1962 or UPC 053392119621 4 Keep your receipt and these Instructions for Proof of Purchase TOOLS REQUIRED FOR ASSEMBLY amp INSTALLATION not included v Ss Safety goggles Wire Strippers Wire Cutters Flathead Screwdriver A Phillips Screwdriver Electrical Tape Ladder 100 watt Max type A bulb not included x2 ADDITIONAL PARTS FOR ASSEMBLY included 1 Chain Loop serene ane v 6 Glass Shade 7 Socket Ring 10 Nipple 11 Finial x2 x2 ASSEMBLT INSTRUCTIONS 1 Carefully unpack the fixture lay out all parts on clean surface 2 The Lower Arms 4 have been turned to lay flat for shipping turn the Lower Arms 4 carefully so that they are evenly spaced apart 3 Place Upper Arm Assembly 3 on top of Distributor 8 and secure by screwing Pole 2 to top of the Distributor 8 4 Screw Chain Loop 1 to top of the Pole 2 5 Screw Nipple 10 to the Coupling 9 6 Screw Finial 11 to the Nipple 10
Download Pdf Manuals
Related Search