Illumine CLI-EMM023903 Instructions / Assembly
Contents
1. 44 WARNING Check to see that ali connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result i 3 Screw the two threaded studs supplied into the tapped holes in the hanger bracket 4 Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover Figure 18 NOTE If you are not sure If the outlet box is 5 Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs supplied Figure 18 Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling and the hole in the ceiling cover is clear of the downrod Your fan is now wired to be turned on and off from the fan switch CEILING f OVER THREADED STUDS 2 segt LOCKWASHERS 2 KNURLED KNOBS 2 Figure 18 4 WARNING To avoid possible fire or shock make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling cover and the ceiling How to Wire Your Ceiling Fan Blue and yellow wires from fan to blue wire from E fanlight control Dual Slide Wall Control Black white wire from fan light control to black NOTE installation of thls control requires that a wire from the 120V AC supply source three conductor ca2. CONTROL Schematic B CONNECTIONS REQUIRED WHEN SUPPLY VOLTAGE IS FED INTO WALL OUTLET BOX GREEN CONDUCTOR CABLE D L W GROUND WIRE BETWEEN CEILING YELLOW AND WALL OUTLET U L BOXES I l I I l E l EG stot SOURCE Figure 22 nan 5 All fans are shipped from the factory with the Operating Your Ceiling Fan reversing switch positioned to circulate air i downward If airflow is desired in opposite with the Wall Control direction turn your fan OFF and wait for the blades to stop turning then slide the reversing switch to l IMPORTANT the opposite position and turn fan on again Fan installation must be completed including the Figure 24 installation of the fan blades before testing of the Ma dirach tamote control 6 The fan blades will turn in the opposite direction and reverse the airflow Your Dual Slide Fan Light Wall Control Figure 23 has full control of your fan and lights Reverse Switch Information w 1 To set the desired fan speed push the fan knob up to operate your fan on low to high speed 1 4 Season Rotation Direction Switch Position settings See Figure 23 Summer Counter Clockwise Right __ 2 To turn your fan off position the knob below the Winter Clockwise Left number 1 setting C 3 To set the level of light brightness push the light knob up to operate your light on low to high settings See Figure 23 To turn the lights off positi
3. wall switch Pull switch out from wall outlet box Install the wall plate using two 6 32 x 1 4 screws supplied Figure 19 9 Installation of the ceiling fan is now complete j 2 Disconnect wire from existing fan wall switch Restore power at the main fuse box or circuit breaker panel WALL OUTLET BOX OUTLET BOX DUAL SLIDE WALL CONTROL SWITCH Figure 19 WALL PLATE Set all knobs on the fan light control in the off down position Figure 20 6 32 x 3 4 SCREW 2 WALL PLATE 6 32 x 1 4 SCREW 2 4 Make the following wire connections Figure 20 and secure with wire connectors supplied Figure 21 Black wire from fan to black wire from fan light control White wire from fan to white wire from the 120V AC supply source 10 NOTE Refer to Schematic A or B depending upon the location of your 120V AC supply source Figure 22 NOTE This wirlng configuration will control accent light and accessory downlight together For other possible wiring switch combinations to contro accent light and downlight consult a licensed electriclan or see other Emerson accessory control Schematic A CONNECTIONS REQUIRED WHEN SUPPLY VOLTAGE IS FED INTO CEILING OUTLET BOX ve CEILING OUTLET BOX 120V AC SUPPLY SOURCE K DASH LINES ARE 3 C a CONDUCTOR CABLE W GROUND WIRE YELLOW BETWEEN CEILING U L AND WALL OUTLET l BOXES WALL OUTLET BOX GROUND
4. be sure that the flanges are installed in a clockwise manner to engage the interlocking feature Be sure alf the flanges are properly engaged and then tighten the flange screws If one of the flanges do not seat properly on the motor hub loosen the adjacent flange screws re engage and reseat the flanges then tighten the screws again C 3 Attach the blade flange assembly using two 1 4 20 x 12mm oval head screws Figure 3 Install the remaining four fan blades assemblies using the same procedure C 4 Gently snug all flange screws to the motor housing working around the housing in a clockwise sequence Failure to follow this procedure could result in fan wobble This completes the blade installation 1 4 20 x 12mm OVAL HEAD BLADE SCREW 2 per flange LS BLADE FLANGE Figure 3 4m WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades 8 amp Hemove and retain one of the switch housing mounting screws Figure 4 from the motor hub Loosen the two remaining switch housing screws Position the switch housing adapter onto the motor hub Rotate the switch housing adapter clockwise to engage the key hole slots Figure 4 Secure the switch housing adapter to the fan motor housing by reinstalling the previously removed screw into the r
5. could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects In between rotating fan blades WARNING To reduce the risk of electrical shock this fan must be installed with a general use isolating wall control switch FOR CANADA THIS FAN MUST BE SECURED DIRECTLY TO THE BUILDING STRUCTURE CEILING JOIST DO NOT SECURE THIS FAN TO AN OUTLET BOX DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep itin a safe place for future use This Manual Is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One stepladder One wire stripper One Phillips head screwdriver MATERIALS Wiring outlet box and box connectors must be of type required by the local code The minimum wire would be a 3 conductor 2 wire with ground of the wire size to right L Wire Size A W G Up to 50 ft 14 50 100 ft 12 A WARNING If you feel you do not have enough wiring knowledge or experience have your fan installed by a licensed electrician Unpacking Instructions For your convenience check off boxes are provided next to each step As each step is completed place a check mark in the box This wi
6. two setscrews must be properly installed as described above or fan wobble could result WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened Failure to verify that the pin and setscrew are properly installed could result In the fan falling MOTOR COUPLING DOWNROD CLEVIS PIN HAIRPIN CLIP Figure 8 NOTE If installing ceiling fan on shorter ceilings and using the 4 5 downrod proceed to Step 16 and then onto Step 21 lf installing ceiling fan on a minimum recommended floor to fan clearance for a 9 foot ceiling using the 10 downrod proceed to Step 17 16 4 5 Downrod Installation Be sure the grommet is properly installed in the coupling cover then slide the coupling cover on the downrod until it rests on the motor housing Be sure that the coupling cover is oriented correctly Figure 9 Proceed to Step 21 to complete assembly f p CHD 4 5 DOWNROD GROMMET COUPLING COVER f D n NL Figure 9 wr NW 17 10 Downrod Installation Hemove the grommet L 22 from the coupiing cover then slide the coupling cover on the downrod until it rests on the motor housing Be sure that the coupling cover is oriented correctly Figure 10 18 Slide the decorative lower scroll onto the 10 downrod positioning the lower lip of the scroll into the hole of the coupling cover Figure 10 L 19 Slide the decorative
7. upper scroll onto the 10 downrod positioning the three interlocking tabs of the decorative upper scroll into the interlocking C 23 tabs of the decorative lower scroll Figure 10 20 Tighten the decorative upper scroll to the 10 downrod using the supplied 2mm hex wrench Figure 10 10 DOWNROD DECORATIVE UPPER SCROLL HEX SCREW INTERLOCKING TABS 3 ON EACH SCROLL DECORATIVE LOWER SCROLL COUPLING COVER WITH GROMMET REMOVED Figure 10 5 21 Position the ceiling cover over the downrod Be sure the cover is oriented correctly with the large opening at the top Figure 11 24 TIGHTEN HEX SCREW 25 Figure 11 40 WATT CANDELABRA BASE LIGHT BULB 4 Figure 13 Reinstall the hanger ball on the downrod as follows Route the motor leads through the hanger ball and slide the hanger ball over the downrod Figure 12 Install the pin through the holes at the top of the downrod and slide the hanger ball up the downrod aligning the ball so the pin is captured in the groove in the top of the hanger ball Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball A loose setscrew could create fan wobble The blue black white and yellow leads exiting the downrod are 80 inches long Before installing the fan measure up approximately 6 to 9 inches above the ball downrod assembly Cut off excess leads and strip back insulation 1 2 inch from end of
8. READ AND SAVE THESE INSTRUCTIONS A WARNING WARNING To avold fire shock and serious personal Injury follow these instructions Safety Instructions 1 Read your owner s manual carefully and keep it for future reference 2 Before attempting installatlon servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accldentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel 3 Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the celling fan before servicing 4 Do not put anything into the fan blades while they are turning Additional Safety Instructions for Installation 1 To avoid possible shock be sure efectricity is turned off at the fuse box before wiring and do not operate fan without blades 2 All wiring must be in accordance with the National Electrical Code ANSI NFPA 70 2008 and Local Electrical Codes Use the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licensed electrician 3 The outlet box and joist must be securely mounted and capable of reliably supporting a least 50 pounds Use only U L outlet boxes liste
9. ble wlth ground wire be run between the contro wall box and the celling fan PUE ee oe EAD outlet YELLOW LIGHT TO HOT BLACK WHITE SWITCH LEAD A WARNING Turning off wall switch is not sufficlent To avoid possible electrical shock be sure electricity is turned off at the main fuse or clrcuit breaker box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precautlon against possible electrical shock WARNING To avold possible fire or shock follow all wiring instructlons carefully Any Electrical work not described in these instructions should be done or approved by a licensed electrician A WARNING To avold possible electrica shock be sure electricity is turned off at the main fuse or circuit breaker panel BACK VIEW SWITCH BLACK SPEED CONTROL LEAD Figure 20 a WARNING Check to see that all connections are tight inctuding ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result NOTE if you are not sure if the outlet box is grounded contact a licensed electrician for advise as it must be grounded for safe operation BE Attach the fandight control to the outlet wall box 1 Remove the wall plate and screws from the existing using two 6 32 x 3 4 screws supplied Figure 21
10. d as Acceptable for Fan Support of 50 ibs or Less and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt 4 The longer downrod 10 furnished with the ceiling fan provides the minimum recommended floor to fan blade clearance for a 9 foot celllng The 4 5 downrod supplied is to be used for shorter ceilings 5 The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with th fan blades 6 Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician NOTE This fan is suitable for use with solid state speed controls WARNING To reduce the risk of fire or electric shock this fan should only be used with fan speed control Model No SW90 U L No UC9031 manufactured by Rhine Electric Co Ltd WARNING To avoid fire shock or injury do not use an Emerson or any other brand of control not specifically approved for this fan WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessorles not designated for use with this product by Emerson Electric Co
11. d electrician for advice as it must be grounded for safe operatlon 1 Connect the green grounding lead from the hanger ball and the green grounding Jead from the hanger bracket to the grounding conductor of supply this may be a bare wire or wire with green colored insulation Securely connect wires with wire connectors supplied NOTE CEILING COVER OMITTED FOR CLARITY BLACK GROUND FAN WIRE BLACK CONTROL WIRE WIRE BLUE AND YELLOW LEAD i WIRES FROM LIGHT WHITE FAN WIRE GREEN WIRE GROUND FROM WHITE SUPPLY HANGER BRACKET NEUTRAL GREEN WIRE GROUND FROM BLUE LEAD WIRE HANGER BALL FROM FAN CONTROL Figure 17 NOTE If you are using an Emerson Light Fixture with your fan see Light Fixture Owner s Manual for wiring 2 Securely connect the fan motor white wire to the supply white neutral wire using wire connector supplied Figure 17 Securely connect the fan motor black wire to the control black wire using wire connector supplied Figure 17 Securely connect light lead blue and light lead yellow wires to blue of fan control After connections have been made turn leads upward and carefully push leads into the outlet box with the white and green leads on one side of the outlet box and the black and blue leads on the other side of the outlet box NOTE See next section How to Wire Your Ceiling Fan Dual Slide Wall Control and Figure 22 to complete wiring connectlons for your fan
12. emaining hole Tighten the three screws at this time SWITCH HOUSING ADAPTER SWITCH HOUSING MOUNTING SCREW Figure 4 gt Be Engage the connector of the switch housing to the switch housing adapter connector Figure 5 The two connectors are keyed and color coded and must be mated correctly color to color before they can be engaged Be sure the connector latch closes properly SWITCH HOUSING SWITCH HOUSING ADAPTER SWITCH HOUSING ADAPTER COLOR amp CODED CONNECTORS N poo SWITCH HOUSING COLOR CODED CONNECTOR Figure 5 CAUTION Before installing and tightening the screws be sure there are no wires pinched between the switch housing adapter and the switch housing 8 Make sure all wires and connectors are inside the switch housing then position the switch housing on the switch housing plate aligning the three holes for installation Secure the switch housing by installing the four 8 32 x 10mm pan head screws Figure 6 SWITCH HOUSING A WARNING To avoid possible fire or shock do not pinch wires between the switch housing and the switch housing adapter 10 Carefully turn partially assembled fan upside down and place gently in the styrofoam from carton in preparation of final installation i i 11 Obtain the 10 hanger ball downrod assembly and remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down t
13. ews 8 Twenty one 10 32 x 22mm oval head CR screws 9 Five 8 32 x 10mm pan head CR screws 10 One 2mm hex wrench 11 One balancing kit NOTE Place the parts from the loose parts bags in small containers to keep them from being lost If any parts are missing contact your local retailer or catalog outlet for replacement before proceeding SSS e SN IMPORTANT Your celling fan is supplled with an Fan Light Dual Slide Wall Control transmitter This allows you to regulate your ceiling fan speed airflow direction and light intensity Optional Emerson Electric Remote and Wall Control may also be used see store or catalog IMPORTANT Your celling fan will not function properly and may be damaged if used with any wall dimmer switch or control other than the Emerson controls listed above Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds 4 WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support of 50 Ibs or Less and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt lf your fan is to replace an e
14. he downrod Figure 7 Remove the pin from the downrod then remove the hanger ball Retain the pin and hanger ball for reinstallation in Step 22 Discard the 10 downrod if using the 4 5 downrod HANGER BALL DOWNROD SETSCREW v NOTE The longer downrod 10 furnished with the ceiling fan provides the minimum recommended floor to fan biade clearance for a 9 foot ceiling The 4 5 downrod supplled Is to be used for shorter ceilings Figure 7 C 12 Separate untwist and unkink the black white and blue motor 80 motor leads Route these wires through the desired downrod 13 Loosed the two setscrews in the motor coupling Slide the downrod down the wires and seat the downrod in the motor coupling Figure 8 14 Align the clevis pin holes in the downrod with the holes in the motor coupling Install the clevis pin and secure with the hairpin clip Figure 8 The clevis pin must go through the holes in the motor coupling and the holes in the downrod Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin The hairpin clip must be properly installed to prevent the clevis pin from working loose Pull on the downrod to make sure the clevis pin is properly installed a 15 While pulling up on the downrod securely tighten the two setscrews in the motor coupling Figure 8 NOTE The
15. leads It Is critical that the pin in the hanger bail is properly Installed and the setscrew securely tightened Failure to verify that the pln and setscrew are properly Installed could result in the fan falling Install four 40 watt candelabra base light bulbs supplied in the uplight sockets Figure 13 UPLIGHT SOCKET 4 You have now completed the initial assembly of your new ceiling fan You can now proceed with hanging and wiring your fan How to Hang Your Ceiling Fan 44 WARNING S HANGER BRACKET TWO SCREWS The fan must be hung with at least 7 of clearance SUE Dot from floor to blades Figure 14 Do NOT hang this fan on an 8 celllng when using the 10 downrod CEILING Figure 15 Carefully lift the fan and seat the hanger ball downrod assembly on the hanger bracket that was just attached to the outlet box Figure 16 Be sure the groove in the ball is lined up with tab on AT LEAST the hanger bracket Figure 15 7 a WARNING Failure to seat tab In groove could cause damage to electrical wires and possible shock or fire hazard FLOOR d Figure 14 4 WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 Ibs Use only a U L outiet box listed as Acceptable for Fan Support of 50 Ibs or Less HANGER a 1 Securely attach the hanger bracket to the outlet box BRACKET using the two screws supplied with the outlet b
16. ll insure that all steps have been completed and will be helpful In flnding your place should you be interrupted Aa WARNING Do not install or use fan if any part is damaged or missing 4 WARNING This product is designed to use only those parts supplied with thls product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage 1 Open styrofoam unit containing fan Remove upper and center sections of styrofoam unit Remove parts and check to see that you have received the following One Fan Motor and Housing Assembly One Ceiling Cover Five Fan Blades Five Flange Assemblies Five Flange Medallion Assemblies One Coupling Cover One Hanger Bracket One 10 Downrod Hanger Ball Assembly One 4 5 Downrod One Decorative Upper Scroll One Decorative Lower Scroll One Switch Housing Adapter m One Switch Cup Finial Nut Assembly n One Fan Light Dual Slide Wall Control transmitter o Four 40 Watt Candelabra Base Bulbs p One loose parts bag containing One clevis pin One hairpin clip Five 12 Ga wire nut connectors Two 8 32 x 1 14 threaded studs Two 8 32 knurled knobs Pii arene ea el ena a O E E ce DA moo move 6 Two 8 external tooth lockwashers 7 Eleven 1 4 20 x 12mm oval head CR scr
17. on the knob below the number bottom setting Figure 24 Figure 23 12
18. ox Figure 15 a WARNING DOWNROD ASSEMBLY To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support of 50 Ibs or Less and use screws supplied with outlet box Most outlet boxes Figure 16 A WARNING commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician If in doubt 44 WARNING Hanger bracket must seat firmly against outlet box If the outlet box is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall To avold possible fire or shock do not pinch wires between the hanger ball downrod assembly and the hanger bracket How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience have your fan Installed by a licensed electrician A WARNING Turning off wall switch Is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring All wirlng must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution agalnst possible electrical shock A WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring grounded contact a license
19. xisting ceiling light fixture turn electricity off at the main fuse box at this time and remove the existing light fixture A WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electriclty Is turned off at the main fuse box before wiring All wiring must be in accordance with national and local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock 4 WARNING To avold possible fire or shock follow all wiring instructions carefully Any electrical work not described in these instructions should be done or approved by a licensed electrician Ceiling Fan Assembly Procedures IMPORTANT Remove the five motor retainers from the motor hub and discard the retainers and retainer screws before installation of flange blade assembly Figure 1 Figure 1 1 Position the flange medallion upside down on a soft clean surface Place the blade with the decorative side facing down onto the flange medallion Attach the flange assembly to the blade and flange medallion using the four 10 32 x 22mm oval head screws as shown in Figure 2 Repeat for the four remaining blades FLANGE MEDALLION ASSEMBLY I pa ac FAN BLADE FAN FLANGE 70 40 32 x 22mm OVAL HEAD BLADE SCREW Figure 2 4 per blade flange NOTE Take care not to scratch fan housing when installing blades L 2 The flange assemblies have interlocking tabs
Download Pdf Manuals
Related Search