Illumine CLI-EMM027611 Installation Guide
Contents
1. HANGER P SAFE BALL DOWNROD J pe RAEE ASSEMBLY CEILING COVER Align the clevis pin holes in the downrod with the holes in the motor yoke Install the clevis pin and secure with the hairpin clip Figure 3 The clevis pin must go through the holes in the motor yoke It is critical that the clevis pin in the motor yoke is properly installed and the setscrews securely tightened Failure to verify that the pin and setscrews are properly installed could result in the fan falling oo LN _ 8 Securely attach the hanger bracket to the outlet A WARNING It is critical that the clevis pin in the motor coupling is properly Installed and the setscrews securely tightened Failure to verify that the pin and setscrews are properly installed as shown in Figure 3 could result in the fan falling Install two setscrews previously removed in Step 2 in the motor yoke Figure 3 While pulling up on the hanger ball securely tighten both setscrews using the setscrew wrench supplied NOTE The setscrews must be properly installed as described above or fan wobble could result 4 WARNING The fan must be hung with at least 10 of clearance from floor to blades Figure 4 mena ee AT LEAST 10 FLOOR Figure 4 A WARNING The outlet box and Joist must be securely mounted and capable of supporting at least 50 Ibs Use only a U L outlet box listed as Acceptable for Fan Support of 50 Ibs or less 44 WAR2. dlack leads on the other side of the outlet box El Check to see that ali connections are tight including ground and that no bare wire is visible at the wire connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result 13 Screw the two 3 4 threaded studs supplied into the tapped holes in the hanger bracket Figure 8 Lift the ceiling cover up to the threaded studs and turn until studs protrude through the holes in the ceiling cover Figure 9 Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the two knurled knobs supplied Figure 9 Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling Your fan is now wired to be turned on and off from the wall switch SAFETY CABLE CEILING COVER STUDS 2 8 LOCKWASHER KNURLED KNOB Figura 9 To avoid possible fire or shock make sure that the electrical wires are compietely inside the outlet box and not pinched between the ceiling cover and the ceiling Ei 16 Pass the end of the safety cable through the two cable clamps supplied Figure 10 Pass the end of the safety cable through the eye screw and then back through the two cable clamps Pesse pis Sh 4 277273 TY EYE SCREW CABLE CLAMP Figure 10 CAUTION H is important to note the proper installation position of the cable clamps as il
3. joist must be securely mounted and capable of reliably supporting at least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support of 50 Ibs or less and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt 4 The fan must be mounted with the fan blades at teast 10 feet from the floor to prevent accidental contact with the fan blades 5 Suitable for use with solld state speed controls 6 Always properly connect the safety cable Included with this fan follow the installation Instructions section carefully 7 The support beam or joist must be secure and capable of supporting at least 50 pounds 8 Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician WARNING To avoid fire shock or injury do not use an Emerson or any other brand of control not specifically approved for this fan WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in persona
4. NING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support of 50 tbs or less and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt box using the two screws supplied with the outlet box Figure 5 44 WARNING Hanger bracket must seat firmly against outlet box If the outlet box is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or fall SUPPLIED WITH HANGER OUTLET BOX BRACKET Figure 5 Screw the eye screw supplied into the joist 7 inches from the center of the ceiling outlet box Figure 6 cs EYE SCREW Figure 6 _ 10 Carefully lift the fan and seat the hanger ball downrod assembly on the hanger bracket that was just attached to the outlet box Figure 7 Be sure the groove in the bali is lined up with the tab on the hanger bracket Figure 5 4 WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard NOTE C SUPPLY FAN WI OUTLET FOR CL BOX HANGER BRACKET NGER BALL WNROD Figure 8 SSEMBLY 44 WARNING To avoid possible fire or shock do not pinch wires between the hanger ball downrod assembly and hang
5. READ AND SAVE THESE INSTRUCTIONS Ee 60 Industrial Heat Fan Owner s Manual Net Weight 19 8 Lbs 44 WARNING WARNING To avoid fire shock and serious personal injury follow these instructions Safety Instructions 1 Read your owner s manual carefully and keep it for future reference 2 Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel 3 Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing 4 Suitable for use with solid state speed controls 5 Do not bend the blade flanges when installing the blades balancing the blades or cleaning the fan Do not insert foreign objects in between the rotating blades Additional Safety Instructions for Installation 1 To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades 2 All wiring must satisfy National and Local Electrical Codes Use the Nationa Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution agalnst possible electrical shock Electrical Installation should be made or approved by a licensed electrician 3 The outlet box and
6. ck Assembly Instructions CAUTION The blade assemblies must be mounted on the motor assembly so that the This Side Up label is visible at the top of the motor Figure 1 Install one blade assembly on the top of the motor assembly using two M6 1 0 x 12mm Phillips hex head screws two split lockwashers and two flat washers supplied Figure 1 Repeat this procedure for the remaining two blade assemblies M6 1 0 x 12mm PHILLIPS HEX HEAD SCREW SPLIT LOGKWASHER FLAT WASHER SETSCREW 2 Figure 1 BE Using the setscrew wrench supplied remove the two setscrews from the top of the motor yoke Figure 1 Retain the setscrews for future use Route the three 48 motor leads and the safety cable through the center hole in the motor cover Align the two holes in the motor cover with the threaded holes in the motor yoke and secure by installing two M4 7 x 10mm pan head knurled screws and two M4 external tooth lockwashers supplied Figure 2 M4 7 x 10mm PAN HEAD KNURLED SCREW 4 J5 Figure 3 Bi Figure 2 M4 EXTERNAL TOOTH LOCKWASHER Route the three motor leads and the safety cable through the center hole in the ceiling cover and position the ceiling cover over the motor yoke Figure 3 Separaie untwist and unkink the three motor leads and the safety cable then route them through the hanger ball downrod assembly and seat the downrod in the motor yoke Figure 3
7. er bracket If you feel that you do not have enough electrical wiring Knowledge or experience have your fan installed by a licensed electrician A WARNING To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring NOTE If you are not sure if the outlet box is grounded contact a licensed electrician for advice as it must be grounded for safe operation Connect the green grounding wire from the hanger ball the green grounding wire from the hanger bracket and the green grounding wire from the fan to the grounding conductor of the supply this may be a bare wire or wire with green colored insulation Securely connect wires with wire connectors supplied Figure 8 BLACK WHITE SUPPLY SUPPLY HOT NEUTRAL eaa T BREEN WIRE E i GROUND FROM FAN h AADA SUPPLY GROUND WIRE HANGER GREEN WIRE p BRACKET GROUND FROM HANGER BALL THREADED GREEN WIRE GROUND a STUD 2 FROM HANGER BRACKET LISTED WIRE Figure 8 CONNECTOR 3 Securely connect the fan motor white wire to the supply white neutral wire using wire connector supplied Figure 8 Securely connect the fan motor black wire to the supply black hot wire using wire connector supplied Figure 8 After connections have been made turn leads upward and carefully push the leads into the outlet box with the wires spread apart and the white and green leads on one side of the outlet box and the
8. issing 4 WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage Ji 3 Electrical Requirements Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds A WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support of 50 Ibs or less and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if In doubt If your fan is to replace an existing ceiling light fixture turn electricity off at the main fuse box at this time and remove the existing light fixture n WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be In accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical sho
9. l injury or property damage WARNING To Reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep itin a safe place for future use Checking Contents of Package 1 Unpack the items carefully to avoid damage to any of the components Check to see that you have received the following parts NOTE If you are uncertain of part description refer to the exploded view illustration a Fan motor assembly b One ceiling cover c One motor cover d Three fan blade assemblies e One hanger bracket f One hanger ball downrod assembly g One loose parts bag containing 1 One clevis pin 2 One hairpin clip 3 Three wire connectors 4 Seven M6 1 0 x 12mm Phillips hex head screws 5 Seven split lockwashers 6 Seven flat washers 7 Two M4 0 7 x imm pan head knurled screws 8 Two M4 external tooth lockwashers 9 Two 8 32 knurled nuts 10 Two 8 external tooth lockwashers 11 Two 8 32 x 0 75 threaded studs 12 Two safety wire clamps 13 One eye screw 14 One setscrew wrench NOTE Intermixing blades between fans can cause excessive wobble Keep blades in original sets of three 4 WARNING Do not install or use fan if any part is damaged or m
10. lustrated in Figure 10 TO obtain maximum holding power install U bolt section of clip on dead or short end of cable and saddle on long end of cable Improper installation reduces the efficiency of the connection by as much as 40 percent 17 After verifying that the cable clamps are positioned properly on the safety cable tighten the nuts on the U bolts Leave one or two inches of slack in the safety cable before tightening the nuts Cut off the excess cable 18 If a remote speed control is to be used refer to the Owner s Manual included with the control for proper installation and wiring E 19 After completing the installation restore the power and test run the fan NOTE When any solid state motor speed control is used a humming noise may be present in the fan on low speed This hum in no way affects the operation of the fan and is acceptable in most industrial installations Maintenance IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed When cleaning use only a soft brush or lint free cloth to avoid scratching the finish Abrasive cleaning agents are not required and should be avoided to prevent damage to finish A WARNING Do not use water when cleaning your ceiling fan It could damage the motor or the blades and create the posslbility of an electrical shock Accessories 1 Ceiling Fan Controls see store
11. or catalog 2 Downrod Extension Kits see store or catalog 4 WARNING The use of any other control not specifically approved for this fan could result in fire shock and personal injury A WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with thls product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage
Download Pdf Manuals
Related Search